scholarly journals The Self-Enforcing Starch–Gluten System—Strain–Dependent Effects of Yeast Metabolites on the Polymeric Matrix

Polymers ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 30
Author(s):  
Thekla Alpers ◽  
Viviane Tauscher ◽  
Thomas Steglich ◽  
Thomas Becker ◽  
Mario Jekle
Keyword(s):  
Strain Hardening ◽  
Polymer System ◽  
Rheological Behaviour ◽  
Rate Dependency ◽  
Lower Strain ◽  
End Point Rate ◽  
The Impact ◽  
Elongational Rheometry ◽  
Strain Dependent ◽  
Strain Hardening Index

The rheological behaviour of dough during the breadmaking process is strongly affected by the accumulation of yeast metabolites in the dough matrix. The impact of metabolites in yeasted dough-like concentrations on the rheology of dough has not been characterised yet for process-relevant deformation types and strain rates, nor has the effect of metabolites on strain hardening behaviour of dough been analysed. We used fundamental shear and elongational rheometry to study the impact of fermentation on the dough microstructure and functionality. Evaluating the influence of the main metabolites, the strongest impact was found for the presence of expanding gas cells due to the accumulation of the yeast metabolite CO2, which was shown to have a destabilising impact on the surrounding dough matrix. Throughout the fermentation process, the polymeric and entangled gluten microstructure was found to be degraded (−37.6% average vessel length, +37.5% end point rate). These microstructural changes were successfully linked to the changing rheological behaviour towards a highly mobile polymer system. An accelerated strain hardening behaviour (+32.5% SHI for yeasted dough) was promoted by the pre-extension of the gluten strands within the lamella around the gas cells. Further, a strain rate dependency was shown, as a lower strain hardening index was observed for slow extension processes. Fast extension seemed to influence the disruption of sterically interacting fragments, leading to entanglements and hindered extensibility.

Statistical micromechanical damage model for SH-SFRC under tensile load considering the interfacial slip-softening and matrix spalling effects

2021 ◽  
pp. 105678952110112
Author(s):  
Hehua Zhu ◽  
Xiangyang Wei ◽  
J Woody Ju ◽  
Qing Chen ◽  
Zhiguo Yan ◽  
...  
Keyword(s):  
Strain Hardening ◽  
Steel Fiber ◽  
Damage Model ◽  
Fiber Reinforced Concrete ◽  
Uniaxial Tensile ◽  
Interfacial Slip ◽  
Fiber Reinforced ◽  
Micromechanical Damage ◽  
The Impact ◽  
Micromechanical Damage Model

Strain hardening behavior can be observed in steel fiber reinforced concretes under tensile loads. In this paper, a statistical micromechanical damage framework is presented for the strain hardening steel fiber reinforced concrete (SH-SFRC) considering the interfacial slip-softening and matrix spalling effects. With a linear slip-softening interface law, an analytical model is developed for the single steel fiber pullout behavior. The crack bridging effects are reached by averaging the contribution of the fibers with different inclined angles. Afterwards, the traditional snubbing factor is modified by considering the fiber snubbing and the matrix spalling effects. By adopting the Weibull distribution, a statistical micromechanical damage model is established with the fracture mechanics based cracking criteria and the stress transfer distance. The comparison with the experimental results demonstrates that the proposed framework is capable of reproducing the SH-SFRC’s uniaxial tensile behavior well. Moreover, the impact of the interfacial slip-softening and matrix spalling effects are further discussed with the presented framework.

A NONLINEAR STRAIN-DEPENDENT VARIABLE-ORDER FRACTIONAL MODEL WITH APPLICATIONS TO ALUMINUM FOAMS

Fractals ◽  
2021 ◽  
Author(s):  
WEI CAI ◽  
PING WANG
Keyword(s):  
Power Law ◽  
Variable Order ◽  
Aluminum Foams ◽  
Static Compression ◽  
Fractional Model ◽  
Comparative Results ◽  
The Impact ◽  
Strain Responses ◽  
Strain Dependent ◽  
Quasi Static Compression

In this paper, a power-law strain-dependent variable order is first incorporated into the fractional constitutive model and employed to describe mechanical behaviors of aluminum foams under quasi-static compression and tension. Comparative results illustrate that power-law strain-dependent variable order is capable of better describing stress–strain responses compared with the traditional linear one. The evolution of fractional order along with the porosities or relative densities can be well qualitatively interpreted by its physical meaning. Furthermore, the model is also extended to characterize the impact behaviors under large constant strain rates. It is observed that fractional model with sinusoidal variable order agrees well with the experimental data of aluminum foams with impact and non-impact surfaces.

scholarly journals Distinct Tumor Microenvironments Are a Defining Feature of Strain-Specific CRISPR/Cas9-Induced MPNSTs

Genes ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 583 ◽  
Author(s):  
Amanda Scherer ◽  
Victoria R. Stephens ◽  
Gavin R. McGivney ◽  
Wade R. Gutierrez ◽  
Emily A. Laverty ◽  
...  
Keyword(s):  
Tumor Microenvironment ◽  
Mouse Models ◽  
Cancer Biology ◽  
Myeloid Cell ◽  
Inbred Strains ◽  
Peripheral Nerve Sheath Tumors ◽  
Tumor Onset ◽  
The Impact ◽  
Strain Dependent

The tumor microenvironment plays important roles in cancer biology, but genetic backgrounds of mouse models can complicate interpretation of tumor phenotypes. A deeper understanding of strain-dependent influences on the tumor microenvironment of genetically-identical tumors is critical to exploring genotype–phenotype relationships, but these interactions can be difficult to identify using traditional Cre/loxP approaches. Here, we use somatic CRISPR/Cas9 tumorigenesis approaches to determine the impact of mouse background on the biology of genetically-identical malignant peripheral nerve sheath tumors (MPNSTs) in four commonly-used inbred strains. To our knowledge, this is the first study to systematically evaluate the impact of host strain on CRISPR/Cas9-generated mouse models. Our data identify multiple strain-dependent phenotypes, including changes in tumor onset and the immune microenvironment. While BALB/c mice develop MPNSTs earlier than other strains, similar tumor onset is observed in C57BL/6, 129X1 and 129/SvJae mice. Indel pattern analysis demonstrates that indel frequency, type and size are similar across all genetic backgrounds. Gene expression and IHC analysis identify multiple strain-dependent differences in CD4+ T cell infiltration and myeloid cell populations, including M2 macrophages and mast cells. These data highlight important strain-specific phenotypes of genomically-matched MPNSTs that have implications for the design of future studies using similar in vivo gene editing approaches.

POSTEROMEDIAL MENISCAL AND ANTERIOR CRUCIATE LIGAMENT STRAINS DURING DYNAMIC ACTIVITIES FOLLOWING ANTERIOR CRUCIATE LIGAMENT RECONSTRUCTION

2020 ◽  
Vol 23 (02) ◽  
pp. 2050010
Author(s):  
Sebastian Tomescu ◽  
Ryan Bakker ◽  
David Wasserstein ◽  
Mayank Kalra ◽  
Micah Nicholls ◽  
...  
Keyword(s):  
Anterior Cruciate Ligament ◽  
Acl Reconstruction ◽  
Strain Difference ◽  
Cruciate Ligament ◽  
Knee Simulator ◽  
Lower Strain ◽  
Healthy Knee ◽  
Anterior Cruciate ◽  
The Impact

Background: Meniscal strain patterns are not well understood during dynamic activities. Furthermore, the impact of ACL reconstruction on meniscal strain has not been thoroughly investigated. The purpose of this study was to characterize ACL and meniscal strain during dynamic activities and investigate the strain difference between ACL-intact and ACL-reconstructed ligament conditions. Methods: ACL and medial meniscal strain were measured in-vitro during gait, a double leg squat, and a single leg squat. For each activity kinematics and muscle forces were applied to seven cadaveric specimens using a dynamic knee simulator. Testing was performed in the ACL-intact and ACL-reconstructed ligament conditions. Results: Both the ACL and meniscus had distinct strain patterns that were found to have a significant interaction with knee angle during gait and double leg squat ([Formula: see text]). During gait, both tissues experienced lower strain during swing than stance (ACL: 3.0% swing, 9.1% stance; meniscus: 0.2% swing, 1.3% stance). Meniscal strain was not found to be different between ACL-intact and ACL-reconstructed conditions ([Formula: see text]). Conclusions: During dynamic activities, the strain in the meniscus was not altered between ACL ligament conditions. This indicates that meniscal mechanics after ACL reconstruction are similar to a healthy knee. These results help further the understanding of osteoarthritis risk after ACL reconstruction.

Strain Dependent Transport and Mechanical Characteristics of High-current and High-Strength Type Ag/Bi2223 Composite Superconductors

2006 ◽  
Vol 946 ◽  
Author(s):  
Malik Idries Adam ◽  
Kozo Osamura
Keyword(s):  
Strain Hardening ◽  
Room Temperature ◽  
Elastic Limit ◽  
Mechanical Characteristics ◽  
High Strength ◽  
High Current ◽  
Composite Superconductors ◽  
Mechanical Stage ◽  
Dependent Transport ◽  
Strain Dependent

ABSTRACTTensile strain dependence of electromechanical characteristics of high-current, (Hic) and high-strength, (Hs) type Ag/Bi2223 composite tapes measured at room temperature, RT and 77K is investigated. Mechanical strength of composites revealed strain-hardening signature in Bi2223 filaments due to plastic strain above the elastic limit. Critical current, Ic maintained constant value up to the elastic limit then decreased slowly before finally dropped to about 10% at 0.19% and 0.39% strain, signaling a three-stage limitation. Microstructure observations and electromechanical response of the composites suggest that a limited longitudinal, transverse, interfacial, granular and transgranular microcracks formed during gradual imposition of strain hardening in Bi2223 filaments may be responsible for the slow reduction of Ic in the medium mechanical stage.

Reliability of Burst Limit States for Damaged and Corroded High Strength Pipelines

2006 ◽  
Author(s):  
Marc A. Maes ◽  
Mamdouh M. Salama ◽  
Markus Dann
Keyword(s):  
Limit State ◽  
High Strength Steels ◽  
High Strength ◽  
Crack Arrest ◽  
Limit States ◽  
Lower Strain ◽  
Margin Of Safety ◽  
Normal Strength ◽  
The Impact

High strength steels (X100 and X120) that are being considered for high pressure gas pipelines differ from conventional steels by exhibiting lower work hardening capacity, lower strain to failure and softening of their HAZ. These differences impact burst limit state and tensile limit state, in addition to crack arrest. In this paper, the impact of the variations in mechanical properties on the reliability of pipe limit states involving ductile burst of damaged or corroded pipe is examined. The paper presents the results of burst limit state analysis using state-of-the-art plastic burst models of strain hardening pipe and considering all the uncertainties that impact the margin of safety of pipes subject to internal pressure. Intact pipes, corroded pipes and externally damaged pipes are considered. A case study comparing the differences between normal strength (X60) pipeline and high strength (X100) pipeline is also presented.

Analysis of Strain Hardening Behaviour of Cast Aluminium Alloy 354 Subjected to Artificial Ageing at Various Temperatures

2013 ◽  
Vol 856 ◽  
pp. 231-235 ◽  
Author(s):  
Aditya Eswar ◽  
Arnav Gupta ◽  
G. Dinesh Babu ◽  
M. Nageswara Rao
Keyword(s):  
Heat Treatment ◽  
Aluminium Alloy ◽  
Strain Hardening ◽  
Automotive Industry ◽  
Mechanical Behaviour ◽  
Artificial Ageing ◽  
Cast Aluminium ◽  
Heat Treated ◽  
Lower Strain ◽  
Wide Scale

Automotive industry makes wide scale use of cast aluminium alloy 354 in the production of crucial components, such as compressor wheels for turbochargers. The compressor wheels undergo T61 heat treatment, involving artificial ageing at 188°C. This study focuses on the possible improvement of the mechanical behaviour of the components by subjecting them to modified heat treatments involving usage of lower artificial ageing temperatures (160, 171 and 177°C). A comparative analysis of tensile properties and strain hardening behaviour has been carried out with different artificial ageing temperatures. Results showed that the heat treatment routinely employed by the industry (aged at 188°C) leads to overageing, thereby resulting in relatively inferior mechanical properties and lower strain hardening rates as compared to the samples heat treated at lower artificial ageing temperatures. It is concluded that lowering of the artificial ageing temperature can lead to a superior state of components with respect to mechanical behaviour.

Sign in / Sign up

Export Citation Format

Share Document