scholarly journals Valorization Strategy for Leather Waste as Filler for High-Density Polyethylene Composites: Analysis of the Thermal Stability, Insulation Properties and Chromium Leaching

Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3313
Author(s):  
Eylem Kiliç ◽  
Helena Oliver-Ortega ◽  
Quim Tarrés ◽  
Marc Delgado-Aguilar ◽  
Pere Fullana-i-Palmer ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
High Density Polyethylene ◽  
Low Cost ◽  
Thermo Gravimetric Analysis ◽  
Chemical Exposure ◽  
High Density ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Leather Waste ◽  
Internal Mixer

Leather waste (BF) and high-density polyethylene (HDPE) were compounded in a lab scale internal mixer and processed by means of injection molding. In this study, leather waste and HDPE composites were characterized by instrumental techniques such as differential scanning calorimetry (DSC), thermo-gravimetric Analysis (TGA), and Fourier transform infrared spectroscopy (FTIR). Physical integrity of composites against chemical exposure and chromium-leaching properties of the composites were also investigated. This study shows that the incorporation of 30% leather waste fiber into HDPE composites decreases the thermal conductivity of the composite samples by 17% in comparison to that of neat HDPE samples. Composites showed no thermal degradation during processing cycle. Strong interfacial bonding between leather waste and polymer results in comparable low-leachate levels to maximum allowed concentration for nonhazardous waste, and good chemical resistance properties. The BF/HDPE composites could be a promising low-cost alternative in industrial application areas of HDPE, where high-mechanical strength and low-thermal conductivity is required.

scholarly journals EFFECT OF CaCO3 FILLER ON THE DEGRADATION OF HIGH DENSITY POLYETHYLENE (HDPE) FILM CONTAINING PROOXIDANTS

2018 ◽  
Vol 56 (3B) ◽  
pp. 79
Author(s):  
Khoi Van Nguyen ◽  
Tung Thanh Nguyen ◽  
Duc Trung Nguyen ◽  
Ha Thi Thu Pham
Keyword(s):  
High Density Polyethylene ◽  
Thermo Gravimetric Analysis ◽  
High Density ◽  
Accelerated Weathering ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Elongation At Break ◽  
Twin Screw ◽  
Morphology Of Films ◽  
Uv Lamp

The aim of this work is investigation of effect of CaCO3 filler on the degradation of high density polyethylene (HDPE) films containing stearate salts as prooxidant additves. The films with thickness of 30 µm were prepared by adding 0.3 % (w/w) prooxidant additives mixture (manganese (II) stearate/feric stearate/cobalt (II) stearate ratio of 18:4:1) and CaCO3 filler from 5 to 20 % (w/w) in HDPE resins using twin screw extruder. The films were carried out accelerated weathering treatment according to ASTM G154 standard (340 nm UV lamp, 8 hours UV, 4 hours condensation at 50 0C) for maximum duration of 96 hours. The mechanical properties, FTIR analysis, Differential Scanning Calorimetry (DSC), Thermo gravimetric analysis (TGA) and Scanning Electron Microscope (SEM) were used to assess the changes in the structure and surface morphology of films during accelerated weathering. The results showed that the degradation rate of HDPE films decreased by adding CaCO3 filler and versused with CaCO3 filler content. FTIR traces revealed that CaCO3 filler didn’t affect to the mechanism of polyethylene degradation. After 96 hours of aceelerated weathering treatment, the elongation at break of the HDPE film with 5 % CaCO3 almost unchanged while this value of the HDPE films with 10 and 20 % CaCO3 decreased significantly (96 % and 100 %, respectively).

Sepiolite as a nanofiller to improve mechanical and thermal behavior of recycled high-density polyethylene

2020 ◽  
Vol 36 (3) ◽  
pp. 185-195 ◽  
Author(s):  
Negin Farshchi ◽  
Yalda K Ostad
Keyword(s):  
Thermal Behavior ◽  
High Density Polyethylene ◽  
Low Cost ◽  
Process Condition ◽  
Softening Temperature ◽  
High Density ◽  
Plastic Pollution ◽  
Scanning Calorimetry ◽  
Melt Flow Rate ◽  
Recycled Hdpe

Regarding the current demand for controlling plastic pollution, recycling of polymer sounds a promising solution. However, recycling causes mechanical and thermal shortcomings in polymers. Addition of nanoparticles to recycled materials may overcome these shortcomings. Nanocomposites can be achieved either by blending or through polymerization. Sepiolite as a nanoparticle enhances the thermal properties of polymers. In this study, the effect of sepiolite as a nanoparticle has been investigated on the thermal and mechanical behavior of recycled high-density polyethylene (HDPE). Hardness, density, Vicat softening temperature, melt flow rate (MFR), and differential scanning calorimetry has been investigated on recycled HDPE containing different amount of sepiolite. Results showed that both the amount of recycled HDPE and the sepiolite content affect the mechanical and thermal behavior of samples. Increasing the amount of recycled component resulted in increasing of MFR, a slight increase in density, and decrease in Vicat softening point, hardness, melting temperature, and degree of crystallization. As an opposite effect of these to factors on crystallinity of HDPE, sepiolite content has better effects to be considered separately for each recycle content. Sepiolite can be introduced as a low-cost reinforcement filler in recycling industry for tuning new compositions based on process condition, or vice versa.

Palm Kernel Shell Filled Recycled High-Density Polyethylene: Effect of Filler Loading

2016 ◽  
Vol 857 ◽  
pp. 191-195 ◽  
Author(s):  
A. Nadiatul Husna ◽  
Bee Ying Lim ◽  
H. Salmah ◽  
Chun Hong Voon
Keyword(s):  
Thermal Stability ◽  
High Density Polyethylene ◽  
Thermo Gravimetric Analysis ◽  
Palm Kernel ◽  
Filler Loading ◽  
High Density ◽  
Gravimetric Analysis ◽  
Melt Mixing ◽  
Palm Kernel Shell ◽  
Thermal Stability Of

Palm kernel shells (PKS) filled recycled high density polyethylene (rHDPE) biocomposites were produced using melt mixing. The biocomposites were prepared on Brabender Plasticorder at temperature of 185 °C and rotor speed of 50 rpm by varying filler loading (0 to 40 phr). In this study, the effect of PKS loading on rheological properties and thermal stability of rHDPE/PKS were investigated. Rheological study of the biocomposites was carried out by means of capillary rheometer under temperature of 190 °C, 200 °C and 210 °C. Thermal properties of biocomposites were studied by using thermo gravimetric analysis (TGA). The rheological results showed that the flowability of the composite increased with increasing temperature. Meanwhile, the result of TGA showed that at higher PKS loading, rHDPE/PKS biocomposites had lower total weight loss. The thermal stability of the biocomposites was reduced due to the addition of filler loading.

scholarly journals Thermal and Structural Properties of High Density Polyethylene/Carbon Nanotube Nanocomposites: A Comparison Study

Chemosensors ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 136
Author(s):  
Ayat Bozeya ◽  
Yahia F. Makableh ◽  
Rund Abu-Zurayk ◽  
Aya Khalaf ◽  
Abeer Al Bawab
Keyword(s):  
Carbon Nanotubes ◽  
Polymer Matrix ◽  
High Density Polyethylene ◽  
High Density ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Melt Compounding ◽  
Multi Walled Carbon Nanotubes ◽  
Functionalization Of Carbon Nanotubes ◽  
Walled Carbon Nanotubes

The effects of functionalization of carbon nanotubes on the properties of nanocomposite sheets prepared from high-density polyethylene (HDPE) and carbon nanotubes (CNTs) were investigated. Carbon nanotubes were first oxidized, followed by amine group functionalization. The Fourier transform-infrared (FTIR) spectroscopy results confirm the presence of oxygenated and amide groups at the surface of the CNTs after each treatment. The HDPE/CNT nanocomposites sheets were prepared using a melt compounding method. Six types of CNTs were used; pristine Single-walled Carbon nanotubes (SWCNT) and pristine Multi-walled Carbon nanotubes (MWCNT), oxidized (O-SWCNT and O-MWCNT) and amide (Amide-SWCNT and Amide-MWCNT). All prepared nanocomposite sheets were characterized using Thermal gravimetric analysis (TGA), Differential scanning calorimetry (DSC), X-ray diffraction (XRD) and scanning electronic microscope (SEM). TGA results measured increased thermal stability of the polymer with the addition of CNTs, O-MWCNT showed the best enhancement. XRD measurements confirmed that the addition of CNTs did not change the crystal structure of the polymer, although the crystallinity was decreased. The maximum crystallinity decrease resulted from O-SWNTs addition to the polymer matrix. SEM imaging showed that oxidized and functionalized CNTs have more even dispersion in the polymer matrix compared with pristine CNTs.

scholarly journals Biocomposites of Bio-Polyethylene Reinforced with a Hydrothermal-Alkaline Sugarcane Bagasse Pulp and Coupled with a Bio-Based Compatibilizer

Molecules ◽  
2020 ◽  
Vol 25 (9) ◽  
pp. 2158
Author(s):  
Nanci Vanesa Ehman ◽  
Diana Ita-Nagy ◽  
Fernando Esteban Felissia ◽  
María Evangelina Vallejos ◽  
Isabel Quispe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Water Absorption ◽  
Sugarcane Bagasse ◽  
Thermo Gravimetric Analysis ◽  
Decomposition Temperature ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Cradle To Gate ◽  
Bagasse Pulp

Bio-polyethylene (BioPE, derived from sugarcane), sugarcane bagasse pulp, and two compatibilizers (fossil and bio-based), were used to manufacture biocomposite filaments for 3D printing. Biocomposite filaments were manufactured and characterized in detail, including measurement of water absorption, mechanical properties, thermal stability and decomposition temperature (thermo-gravimetric analysis (TGA)). Differential scanning calorimetry (DSC) was performed to measure the glass transition temperature (Tg). Scanning electron microscopy (SEM) was applied to assess the fracture area of the filaments after mechanical testing. Increases of up to 10% in water absorption were measured for the samples with 40 wt% fibers and the fossil compatibilizer. The mechanical properties were improved by increasing the fraction of bagasse fibers from 0% to 20% and 40%. The suitability of the biocomposite filaments was tested for 3D printing, and some shapes were printed as demonstrators. Importantly, in a cradle-to-gate life cycle analysis of the biocomposites, we demonstrated that replacing fossil compatibilizer with a bio-based compatibilizer contributes to a reduction in CO2-eq emissions, and an increase in CO2 capture, achieving a CO2-eq storage of 2.12 kg CO2 eq/kg for the biocomposite containing 40% bagasse fibers and 6% bio-based compatibilizer.

Synthesis, characterization and corrosion protection properties of polyN-(p-bromophenyl)-2-methacrylamide-co-glycidyl methacrylate on low nickel stainless steel

2011 ◽  
Vol 31 (2-3) ◽  
Author(s):  
Sakvai Mohammed Safiullah ◽  
Deivasigamani Thirumoolan ◽  
Kottur Anver Basha ◽  
K. Mani Govindaraju ◽  
Dhanraj Gopi ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Protection ◽  
Glycidyl Methacrylate ◽  
Electrochemical Impedance ◽  
Thermo Gravimetric Analysis ◽  
Gel Permeation Chromatography ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Protection Efficiency ◽  
Ft Ir

Abstract The synthesis of copolymers from different feed ratios of N-(p-bromophenyl)-2- methacrylamide (PBPMA) and glycidyl methacrylate (GMA) was achieved by using free radical solution polymerization technique and characterized using FT-IR, 1H and 13C NMR spectroscopy. The thermal stability of the synthesized copolymers was studied using thermo-gravimetric analysis (TGA) and differential scanning calorimetry (DSC). The molecular weight of the copolymer is determined by gel permeation chromatography (GPC). The corrosion performances of low nickel stainless steel specimens dip coated with different composition of copolymers were investigated in 0.5 M H2SO4 using potentiodynamic polarization and electrochemical impedance spectroscopic (EIS) techniques. The polarization and impedance measurements showed different corrosion protection efficiency with change in composition of the copolymers. It was found that the corrosion protection properties are owing to the barrier effect of the polymer layer covered on the low nickel stainless steel surfaces. However, it is observed that the mole ratio of PBPMA and GMA plays a major role in the protective nature of the copolymer.

Graphene Nanoplates Filled Nylon 6,6 Nanocomposites, Morphological, Thermal, Mechanical and Solvent Uptake Study

2019 ◽  
Vol 41 (3) ◽  
pp. 388-388
Author(s):  
Khalid Saeed Khalid Saeed ◽  
Tariq Shah and Ahmad Hassan Tariq Shah and Ahmad Hassan
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Neutral Red ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Nucleation Effect ◽  
Morphological Studies ◽  
Solvent Uptake ◽  
Nylon 6,6 ◽  
Dsc Analyses ◽  
Graphene Nanoplates

Effect of graphene nanoplates (GNPs) on the properties of Nylon 6,6 (Nyl 6,6) is investigated in present study. The morphological studies presented that the GNPs were dispersed inside the Nyl 6,6 matrix. The thermo gravimetric analysis (TGA) illustrated that the thermal degradation of nanocomposites samples were started at the range of 350-393 oC, which was appreciably higher than neat Nyl 6,6 (360 oC). The differential scanning calorimetry (DSC) analyses revealed that the crystallization temperature (Tc) of GNPs/Nyl 6,6 increased as increased the addition of GNPs, which might be due to the nucleation effect of GNPs. The mechanical properties of Nyl 6,6 was enhanced by incorporation of GNPs upto the addition of an optimal quantity of filler (5%wt GNPs) into the polymer matrix. The stress yield and Young’s modulus of 5%wt GNPs/Nyl 6,6 was 96.79 and 1.54, N/nm2, respectively. Both Nyl 6,6 and nanocomposites samples were also used for the adsorption of Neutral red chloride (NRC) dye, which significantly remove the dye from the aqueous solution. The neat nylon 6,6 and GNPs (5 and 10 wt%)/Nyl 6,6 adsorbed about 88.49, 93.15, and 93.60% within 2 h, respectively.

Characterization of Novel Solid Dispersions of Moringa oleifera Leaf Powder Using Thermo-Analytical Techniques

Processes ◽  
2021 ◽  
Vol 9 (12) ◽  
pp. 2230
Author(s):  
Nontsikelelo Noxolo Tafu ◽  
Victoria A. Jideani
Keyword(s):  
Solid Dispersion ◽  
Moringa Oleifera ◽  
Solid Dispersions ◽  
Intermolecular Hydrogen Bond ◽  
Thermo Gravimetric Analysis ◽  
Analytical Techniques ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Hydrogen Bond Interactions ◽  
Leaf Powder

Moringa oleifera leaf powder (MOLP) has been identified as the most important functional ingredient owing to its rich nutritional profile and healthy effects. The solubility and functional properties of this ingredient can be enhanced through solid dispersion technology. This study aimed to investigate the effects of polyethylene glycols (PEGs) 4000 and 6000 as hydrophilic carriers and solid dispersion techniques (freeze-drying, melting, solvent evaporation, and microwave irradiation) on the crystallinity and thermal stability of solid-dispersed Moringa oleifera leaf powders (SDMOLPs). SDMOLPs were dully characterized using powder X-ray diffraction (PXRD), differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FTIR). The PXRD results revealed that the solid dispersions were partially amorphous with strong diffraction peaks at 2θ values of 19° and 23°. The calorimetric and thermogravimetric curves showed that PEGs conferred greater stability on the dispersions. The FTIR studyrevealed the existence of strong intermolecular hydrogen bond interactions between MOLP and PEG functional groups. MOLP solid dispersions may be useful in functional foods and beverages and nutraceutical formulations.

Decellularized liver-regenerative 3D printing biomaterials for cell-based liver therapies via a designed procedure combined with papain-containing reagent treatments and supercritical fluids

2021 ◽  
pp. 1-8
Author(s):  
Ching-Cheng Huang
Keyword(s):  
3D Printing ◽  
Thermo Gravimetric Analysis ◽  
Extraction Process ◽  
Gravimetric Analysis ◽  
Collagen Scaffolds ◽  
Scanning Calorimetry ◽  
Porcine Liver ◽  
Good Thermal Stability ◽  
Decellularized Liver ◽  
Liver Collagen

BACKGROUND: The biologic scaffolds derived from decellularized tissues and organs have been successfully developed in a variety of preclinical and/or clinical studies. OBJECTIVE: The new decellularized liver-regenerative 3D printing biomaterials were designed and prepared for cell-based liver therapies. METHODS: An extraction process was employed to remove the tissue and cellular molecules from porcine liver via pretreatment of supercritical fluid of carbon dioxide (ScCO2). Varying porosities of the decellularized liver tissues were created using papain-containing reagent treatments after ScCO2. RESULTS: The resulting liver-regenerative 3D printing biomaterials of decellularized liver collagen scaffolds were characterized by Fourier transform infrared spectroscopy, thermo-gravimetric analysis, differential scanning calorimetry and scanning electron microscopy. CONCLUSIONS: The decellularized liver collagen scaffolds with good thermal stability (>150 °C) were obtained and employed as liver-regenerative 3D printing biomaterials for cell-based liver therapies.

The Influence of Nickel Oxide Nanoparticle Dispersion on the Thermo Stability of Lubricant Oil

2019 ◽  
Vol 19 (01) ◽  
pp. 1850044
Author(s):  
K. Ramachandran ◽  
P. Navaneethakrishnan ◽  
M. Sivaraja
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
Nanoparticle Dispersion ◽  
Nio Nanoparticles ◽  
Scanning Calorimetry ◽  
Lubricant Oil ◽  
Nickel Oxide Nanoparticle ◽  
Nanoparticles Dispersion ◽  
Thermo Stability

The homogeneous and substantial dispersion of nanoparticles into base fluids is vital since the final properties of any nanolubricant are estimated by their quality of stability. This paper addresses the effect of NiO nanoparticles dispersion into SN500 lubricant oil and its nonisothermal thermo stability. The dispersion of NiO nanoparticles is achieved by ultrasonication method. The thermo stability is estimated by Thermo Gravimetric Analysis (TGA), Differential Thermal Analysis (DTA) and Differential Scanning Calorimetry (DSC). The result shows that the thermo stability of base fluid enhances up to 0.3[Formula: see text]wt.% particle concentration then it decreases due to agglomeration of dispersed nanoparticles. The findings recommend that 0.1[Formula: see text]wt.% and 0.3[Formula: see text]wt.% of NiO-nanolubricant can be used for the temperature-dependent applications up to 200∘C.

Sign in / Sign up

Export Citation Format

Share Document