scholarly journals Possibilities for Groundwater Flow Sensing with Fiber Bragg Grating Sensors

Sensors ◽  
2019 ◽  
Vol 19 (7) ◽  
pp. 1730 ◽  
Author(s):  
Sandra Drusová ◽  
Wiecher Bakx ◽  
Adam D. Wexler ◽  
Herman L. Offerhaus
Keyword(s):  
Groundwater Flow ◽  
Fiber Bragg Grating ◽  
Optical Fibers ◽  
Flow Direction ◽  
Bragg Grating ◽  
Flow Monitoring ◽  
Flow Sensing ◽  
Well Clogging ◽  
Technical Specifications ◽  
Fbg Sensors

An understanding of groundwater flow near drinking water extraction wells is crucial when it comes to avoiding well clogging and pollution. A promising new approach to groundwater flow monitoring is the deployment of a network of optical fibers with fiber Bragg grating (FBG) sensors. In preparation for a field experiment, a laboratory scale aquifer was constructed to investigate the feasibility of FBG sensors for this application. Multiparameter FBG sensors were able to detect changes in temperature, pressure, and fiber shape with sensitivities influenced by the packaging. The first results showed that, in a simulated environment with a flow velocity of 2.9 m/d, FBG strain effects were more pronounced than initially expected. FBG sensors of a pressure-induced strain implemented in a spatial array could form a multiplexed sensor for the groundwater flow direction and magnitude. Within the scope of this research, key technical specifications of FBG interrogators for groundwater flow sensing were also identified.

scholarly journals Femtosecond-Laser-Assisted Fabrication of Radiation-Resistant Fiber Bragg Grating Sensors

2022 ◽  
Vol 12 (2) ◽  
pp. 886
Author(s):  
Hun-Kook Choi ◽  
Young-Jun Jung ◽  
Bong-Ahn Yu ◽  
Jae-Hee Sung ◽  
Ik-Bu Sohn ◽  
...  
Keyword(s):  
Femtosecond Laser ◽  
Fiber Bragg Grating ◽  
Optical Fibers ◽  
Coming Out ◽  
Single Mode ◽  
Femtosecond Laser Irradiation ◽  
Bragg Grating ◽  
Wavelength Shift ◽  
Radiation Resistant ◽  
Fbg Sensors

This paper demonstrates the fabrication of radiation-resistant fiber Bragg grating (FBG) sensors using infrared femtosecond laser irradiation. FBG sensors were written inside acrylate-coated fluorine-doped single-mode specialty optical fibers. We detected the Bragg resonance at 1542 nm. By controlling the irradiation conditions, we improved the signal strength coming out from the FBG sensors. A significant reduction in the Bragg wavelength shift was detected in the fabricated FBG sensors for a radiation dose up to 105 gray, indicating excellent radiation resistance capabilities. We also characterized the temperature sensitivity of the radiation-resistant FBG sensors and detected outstanding performance.

scholarly journals Dynamic Consolidation Measurements in a Well Field Using Fiber Bragg Grating Sensors

Sensors ◽  
2019 ◽  
Vol 19 (20) ◽  
pp. 4403 ◽  
Author(s):  
Sandra Drusová ◽  
R. Martijn Wagterveld ◽  
Adam D. Wexler ◽  
Herman L. Offerhaus
Keyword(s):  
Groundwater Flow ◽  
Fiber Bragg Grating ◽  
Strain Sensors ◽  
Bragg Grating ◽  
Soil Consolidation ◽  
Flow Monitoring ◽  
Well Field ◽  
Term Data

Currently available groundwater flow prediction tools and methods are limited by insufficient spatial resolution of subsurface data and the unknown local heterogeneity. In this field study, fiber Bragg grating (FBG) sensors were installed in an extraction well field to investigate its potential to measure groundwater flow velocity. Reference in-situ pore pressure and temperature measurements were used to identify possible sources of FBG responses. FBG strain sensors were able to detect soil consolidation caused by groundwater extraction from 250 m distance. The results show that FBG responses were influenced by interface friction between soil and FBG packaging. FBG packaging slipped in soil and the effect was more pronounced during higher groundwater flow around a nearby well. These FBG fibers could be applied for indirect flow monitoring that does not require any tracer and provide real-time and long-term data during regular operation of extraction wells.

Investigation on Temperature Compensation of Fiber Bragg Grating Sensors for Hull Monitoring

2018 ◽  
Author(s):  
Ruiqi Ma ◽  
Guoqing Feng ◽  
Huilong Ren ◽  
Peng Fu ◽  
Shuang Wu ◽  
...  
Keyword(s):  
Thermal Expansion ◽  
Fiber Bragg Grating ◽  
Temperature Compensation ◽  
Compensation Method ◽  
Bragg Grating ◽  
Theoretical Derivation ◽  
Temperature Changes ◽  
Hull Girder ◽  
Fbg Sensor ◽  
Fbg Sensors

Hull monitoring system with Fiber Bragg Grating (FBG) sensors increasingly receives people’s attentions. However, for the ship hull monitoring, the deformation of hull girder changes a lot as is subjected to a huge temperature variation. Therefore, the compensation method with only FBG temperature self-correction is not suitable for the hull monitoring sensors because no material thermal expansion effects are reasonably included. In this paper, the new compensation method of hull monitoring FBG sensor based on the sensor theory with both FBG temperature self-correction and steel thermal expansion effects correction is studied. The coupled compensation method suitable for hull monitoring sensor is obtained by theoretical derivation. As the comparison, the coupled compensation experiment was carried out. The results show that the relative error under the temperature compensation method is large in the case of drastic strain and temperature changes, and the correction results of the tested method will be closer to the true level.

Vibration Fatigue Test Based on Fiber Bragg Grating Sensors and HHT

2013 ◽  
Vol 328 ◽  
pp. 193-197
Author(s):  
Si Jin Xin ◽  
Zhen Tong
Keyword(s):  
Titanium Alloy ◽  
Fiber Bragg Grating ◽  
Fatigue Test ◽  
Alloy Sheet ◽  
Bragg Grating ◽  
Metal Fatigue ◽  
Hilbert Huang Transform ◽  
Time Frequency ◽  
Vibration Fatigue ◽  
Fbg Sensors

The metal fatigue is an important factor to cause an accident in machine operation, so metal fatigue test is a significant procedure in manufacturing. Fiber Bragg Grating (FBG), as an innovative sensor, has been applied to the measurement of various rotating machines. In this paper, the time-frequency analysis is used to detect the fatigue feature of a titanium alloy measured by FBG sensors. Furthermore, the Hilbert-Huang transform (HHT) is more effective to observe the fatigue limit of the titanium alloy sheet, compared to the Wavelet transform (WT).

Measurement of the Thermal Expansion for Space Structures Using Fiber Bragg Grating Sensors and Displacement Measuring Interferometers

2008 ◽  
Author(s):  
Hong-Il Kim ◽  
Lae-Hyong Kang ◽  
Jae-Hung Han
Keyword(s):  
Fiber Bragg Grating ◽  
Real Time ◽  
Deformation Monitoring ◽  
Space Environment ◽  
Space Structures ◽  
Bragg Grating ◽  
Environment Change ◽  
Time Deformation ◽  
Fiber Bragg Grating Sensors ◽  
Fbg Sensors

Dimensional stability of the space structures, such as large telescope mirrors or metering substructures, is very important because even extremely small deformations of these structures might degrade the optical performances. Therefore, precise deformation data of the space structures according to environment change are required to design these structures correctly. Also, real-time deformation monitoring of these structures in space environment is demanded to verify whether these structures are properly designed or manufactured. FBG (fiber Bragg grating) sensors are applicable to real time monitoring of the space structure because they can be embedded onto the structures with minimal weight penalty. In this research, therefore, thermal deformation measurement system for the space structures, composed of FBG sensors for real time strain measurement and DMI (displacement measuring interferometers) for accurate specimen expansion data acquisition, is developed. Thermal strains measured by distributed FBG sensors are evaluated by the comparison with the strains obtained by highly accurate DMI.

scholarly journals Study on the Optimal Groove Shape and Glue Material for Fiber Bragg Grating Measuring Bolts

Sensors ◽  
2018 ◽  
Vol 18 (6) ◽  
pp. 1799 ◽  
Author(s):  
Yiming Zhao ◽  
Nong Zhang ◽  
Guangyao Si ◽  
Xuehua Li
Keyword(s):  
Fiber Bragg Grating ◽  
Linear Regression Analysis ◽  
Tensile Load ◽  
Tensile Tests ◽  
Bragg Grating ◽  
Engineering Practice ◽  
Direct Tension ◽  
Groove Shape ◽  
Fbg Sensors ◽  
The Impact

Fiber Bragg grating (FBG) measuring bolts, as a useful tool to evaluate the behaviors of steel bolts in underground engineering, can be manufactured by gluing the FBG sensors inside the grooves, which are usually symmetrical cuts along the steel bolt rod. The selection of the cut shape and the glue types could perceivably affect the final supporting strength of the bolts. Unfortunately, the impact of cut shape and glue type on bolting strength is not yet clear. In this study, based on direct tension tests, full tensile load–displacement curves of rock bolts with different groove shapes were obtained and analyzed. The effects of groove shape on the bolt strength were discussed, and the stress redistribution in the cross-section of a rock bolt with different grooves was simulated using ANSYS. The results indicated that the trapezoidal groove is best for manufacturing the FBG bolt due to its low reduction of supporting strength. Four types of glues commonly used for the FBG sensors were assessed by conducting tensile tests on the mechanical testing and simulation system and the static and dynamic optical interrogators system. Using linear regression analysis, the relationship between the reflected wavelength of FBG sensors and tensile load was obtained. Practical recommendations for glue selection in engineering practice are also provided.

scholarly journals Stress Monitoring on GFRP Anchors Based on Fiber Bragg Grating Sensors

Sensors ◽  
2019 ◽  
Vol 19 (7) ◽  
pp. 1507 ◽  
Author(s):  
Hai-Lei Kou ◽  
Wang Li ◽  
Wang-Chun Zhang ◽  
Yuan Zhou ◽  
Xiao-Long Zhou
Keyword(s):  
Fiber Bragg Grating ◽  
Field Test ◽  
Weight Ratio ◽  
Electromagnetic Properties ◽  
Bragg Grating ◽  
Shear Stresses ◽  
Stress Profile ◽  
Stress Monitoring ◽  
Axial Forces ◽  
Fbg Sensors

Glass fiber-reinforced polymer (GFRP) bolts have been widely used in some applications of grouted anchors because of the advantages of better resistance to corrosion, high strength-to-weight ratio, low electromagnetic properties, and so on. This study presents a field test to assess the feasibility of fiber Bragg grating (FBG) sensors in monitoring the stress profile of GFRP anchors during pulling test. Two GFRP anchors were fully instrumented with FBG sensors and then installed into the ground using a drilling and grouting method. To measure the stress profile along test anchors, seven bare FBG sensors were arranged in a single optical fiber and then embedded in the middle of GFRP bolts in the process of extrusion molding. The procedure for embedding bare FBG sensors into GFRP bolts is introduced first. Then, the axial forces and shear stresses that were calculated from the measurements of the FBG sensors are discussed. The field test results indicate that the embedded FBG technology was feasible to monitor the stress state of GFRP anchors during pulling.

Detection of missing fastener based on vibration mode analysis using fiber Bragg grating (FBG) sensors

2003 ◽  
Author(s):  
Akiyoshi Shimada ◽  
Kei Urabe ◽  
Yoshihiro Kikushima ◽  
Jun Takahashi ◽  
Kazuro Kageyama
Keyword(s):  
Fiber Bragg Grating ◽  
Vibration Mode ◽  
Mode Analysis ◽  
Bragg Grating ◽  
Fbg Sensors

A smart insole for monitoring plantar pressure based on the fiber Bragg grating sensing technique

2019 ◽  
Vol 89 (17) ◽  
pp. 3433-3446 ◽  
Author(s):  
Rafique Ahmed Lakho ◽  
Zhang Yi-Fan ◽  
Jiang Jin-Hua ◽  
Hong Cheng-Yu ◽  
Zamir Ahmed Abro
Keyword(s):  
Optical Fiber ◽  
Pressure Distribution ◽  
Fiber Bragg Grating ◽  
Plantar Pressure ◽  
Bragg Grating ◽  
Body Postures ◽  
Plantar Pressure Distribution ◽  
The Subject ◽  
Fbg Sensors ◽  
Smart Insole

The analysis of plantar pressure distribution is essential in the field of biomedical and sports-related applications. In this study, a smart insole was developed for the measurement of plantar pressure distribution and the evaluation of body postures using optical fiber Bragg grating (FBG) sensing technology. Four FBG sensors characterized by four different center Bragg wavelengths, 1528 ± 0.3, 1532 ± 0.3, 1535 ± 0.3 and 1539 ± 0.3 nm, were located at the first metatarsus, third metatarsus, fifth metatarsus and heel position, respectively. The measurement sensitivity of all the FBG sensors was 0.000412 nm/kPa, approximately. Silica gel material of modulus = 10 MPa was selected to incorporate the FBG sensors. All FBG sensors were multiplexed together with one optical fiber cable. The performance and functional properties of all FBG-based pressure sensors were calibrated in the laboratory to evaluate plantar pressure distribution. A male subject was selected for performing four tasks, namely standing in an upright position, leaning forward, squat position and forward fold. During standing tests, plantar pressure observed at the heel position was around 57% higher than that at the first and third metatarsus, while the pressure of the fifth metatarsus position presents minimal pressure, which is only 37% that of the pressure of the heel position. When the subject performs leaning forward, the squat position and forward fold posture, the first and third metatarsi show maximum pressure, while the pressure decreases at the fifth metatarsus position. However, almost zero pressure is observed at the heel position when the subject changes the body postures of leaning forward, squat and forward fold posture. The extreme pressure of the forward fold posture was 1750 kPa acquired at the first metatarsus, which is 52% and 62% higher than those at the fifth and third metatarsi, respectively. Therefore, the smart insole successfully recorded both plantar pressure distribution and body posture changes regarding the wavelength values collected by the FBG sensors.

A fiber Bragg grating-based smart wearable belt for monitoring knee joint postures

2019 ◽  
Vol 90 (3-4) ◽  
pp. 386-394 ◽  
Author(s):  
Zamir Ahmed Abro ◽  
Chengyu Hong ◽  
Nanliang Chen ◽  
Yifan Zhang ◽  
Rafique Ahmed Lakho ◽  
...  
Keyword(s):  
Knee Joint ◽  
Fiber Bragg Grating ◽  
Male Subject ◽  
Bend Angle ◽  
Bragg Grating ◽  
Accurate Information ◽  
Measurement Sensitivity ◽  
Static Tests ◽  
Fbg Sensors ◽  
Smart Wearable

Smart wearable technology is exceedingly desirable in athletic sports due to being lightweight, flexible to bend, soft and comfortable. It can continuously deliver accurate information and deformation. During knee flexion, the upper knee perimeter increases with the shrinkage of the knee joint flexor, and it can be monitored. In this study, a fiber Bragg grating (FBG) smart belt is fabricated by embedding FBG sensors at the center of a special silica gel (with unique adhering characteristics to fix FBG on the surface of the belt) for sensing knee joint movements. Polyvinyl chloride strips were adhered to the surface of the smart wearable belt for better protection. The smart belt was calibrated in the laboratory by a systematical changing knee posture and used to identify body postures at various static and kinematic postures of a male subject. The FBG-based smart wearable belt presented a consistent wavelength change after each step by angle changes at the knee joint position. The wavelength increment of FBG sensors increases linearly with the increasing of the bend angle of the knee joint in static tests, and the related slope ratio was 0.3 nm/°. In a jogging test, the measurement sensitivity achieved by the FBG smart wearable belt was within a range between 0.018/° and 0.021 nm/° for the male subject at the velocities of 2 and 3 km/h, respectively. The smart wearable belt could be a useful index to characterize a simple design and ease of implementation, and could also applied for knee posture circumferential strain measurements, especially for sports activities and monitoring stroke patients. This FBG smart belt can be fabricated to produce smart sensing fabrics.

Sign in / Sign up

Export Citation Format

Share Document