scholarly journals Effects of Chemical State of the Pd Species on H2 Sensing Characteristics of PdOx/SnO2 Based Chemiresistive Sensors

Sensors ◽  
2019 ◽  
Vol 19 (14) ◽  
pp. 3131 ◽  
Author(s):  
Tianjiao Qi ◽  
Jie Sun ◽  
Xi Yang ◽  
Fanfan Yan ◽  
Ji Zuo
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Sno2 Nanoparticles ◽  
X Ray ◽  
Transmission Electron ◽  
Response Change ◽  
Hydrogen Response ◽  
Chemical States ◽  
Sensing Characteristics

In this paper, the PdOx nanoparticles modified SnO2 are prepared using sputtering and wet chemical methods. The SnO2 nanoparticles are separately added to a concentration of 0.75% to 10% PdCl2 to obtain a PdCl2/SnO2 composite material, which is calcined for 1 to 2 h at the temperatures of 120 °C, 250 °C, 450 °C and 600 °C. The PdOx/SnO2 nanocomposite was characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffractometry (XRD) and transmission electron microscopy (TEM). Microstructural observations revealed PdOx with different chemical states attached to the surface of SnO2. Hydrogen response change tests were performed on the obtained PdOx/SnO2 gas sensing materials. The results show that the high gas sensing performance may be attributed to the contribution of the PdOx-loaded SnO2. In hydrogen, the best sensitivity response was attained at 80 °C, which is 60 times that of pristine SnO2. It clarifies the role of PdOx in the gas sensing mechanisms.

scholarly journals Defective TiO2 Core-Shell Magnetic Photocatalyst Modified with Plasmonic Nanoparticles for Visible Light-Induced Photocatalytic Activity

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 672 ◽  
Author(s):  
Zuzanna Bielan ◽  
Agnieszka Sulowska ◽  
Szymon Dudziak ◽  
Katarzyna Siuzdak ◽  
Jacek Ryl ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Phenol Degradation ◽  
Magnetic Core ◽  
Magnetic Photocatalyst ◽  
X Ray ◽  
Transmission Electron ◽  
First Time

In the presented work, for the first time, the metal-modified defective titanium(IV) oxide nanoparticles with well-defined titanium vacancies, was successfully obtained. Introducing platinum and copper nanoparticles (NPs) as surface modifiers of defective d-TiO2 significantly increased the photocatalytic activity in both UV-Vis and Vis light ranges. Moreover, metal NPs deposition on the magnetic core allowed for the effective separation and reuse of the nanometer-sized photocatalyst from the suspension after the treatment process. The obtained Fe3O4@SiO2/d-TiO2-Pt/Cu photocatalysts were characterized by X-ray diffractometry (XRD) and specific surface area (BET) measurements, UV-Vis diffuse reflectance spectroscopy (DR-UV/Vis), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Further, the mechanism of phenol degradation and the role of four oxidative species (h+, e−, •OH, and •O2−) in the studied photocatalytic process were investigated.

One-Pot Hydrothermal Synthesis of Sulfur-Doped SnO2 Nanoparticles and their Enhanced Photocatalytic Properties

NANO ◽  
2016 ◽  
Vol 11 (03) ◽  
pp. 1650035 ◽  
Author(s):  
Lin Ma ◽  
Limei Xu ◽  
Xuyao Xu ◽  
Xiaoping Zhou ◽  
Lingling Zhang
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Sno2 Nanoparticles ◽  
Light Response ◽  
One Pot ◽  
X Ray ◽  
Transmission Electron ◽  
Light Region ◽  
Vis Spectroscopy

Sulfur-doped SnO2 nanoparticles with ultrafine sizes have been successfully prepared by a one-pot hydrothermal method. The obtained samples are characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (HRTEM), thermogravimetric (TG), analyzer UV-Vis spectroscopy, photoluminescence (PL) and electrochemical impedance spectroscopy (EIS). The experimental results indicate that the doping level of sulfur element as well as the bandgaps of SnO2 can be controlled to a certain extent by varying the amount of L-cysteine (L-cys). When evaluated as photocatalysts in the degradation of rhodamine B (RhB) and reduction of Cr(VI) under visible light region, the resultant sulfur-doped SnO2 nanoparticles demonstrate obviously enhanced photocatalytic activities due to the markedly improved visible light response and effective separation of the photo-generated electron–hole pairs.

scholarly journals Liquid petroleum gas sensing performance enhanced by CuO modification of nanocrystalline ZnO-TiO2

2016 ◽  
Vol 34 (3) ◽  
pp. 571-581
Author(s):  
R.B. Pedhekar ◽  
F.C. Raghuwanshi ◽  
V.D. Kapse
Keyword(s):  
Thick Film ◽  
Gas Sensing ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molar Ratios ◽  
Transmission Electron ◽  
Liquid Petroleum Gas ◽  
Synthesized Materials ◽  
Sensing Characteristics

AbstractNanocrystalline ZnO-TiO2 (with molar ratios 9:1, 7:3, 1:1, 3:7 and 1:9) were successfully synthesized by hydrothermal method. Synthesized materials were examined with the help of X-ray diffraction and transmission electron microscope. Liquid petroleum gas sensing characteristics of the ZnO-TiO2 films were investigated at different operating temperatures. The ZnO-TiO2 thick film (with 1:1 molar ratio) exhibited good response toward liquid petroleum gas as compared to other investigated compositions. Further, liquid petroleum gas sensing characteristics of CuO modified ZnO-TiO2 thick films were investigated. 0.2 M CuO modified ZnO-TiO2 thick film exhibited excellent liquid petroleum gas sensing characteristics such as higher response (~ 1637.49 at 185 °C) with quick response time (~30 s), low recovery time (~70 s), excellent repeatability and stability at low operating temperature.

scholarly journals Highly sensitive and selective sensing of H2S gas using precipitation and impregnation-made CuO/SnO2 thick films

2021 ◽  
Author(s):  
Pimpan Leangtanom ◽  
Anurat Wisitsoraat ◽  
Kata Jaruwongrangsee ◽  
Narong Chanlek ◽  
Adisorn Tuantranont ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Fast Response ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cu Content ◽  
Transmission Electron ◽  
Highly Sensitive

Abstract In this work, CuO-loaded tetragonal SnO2 nanoparticles (CuO/SnO2 NPs) were synthesized using precipitation/impregnation methods with varying Cu contents of 0–25 wt% and characterized for H2S detection. The material phase, morphology, chemical composition and specific surface area of NPs were evaluated using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and Brunauer-Emmett-Teller analysis. From gas-sensing data, the H2S responses of SnO2 NPs were greatly enhanced by CuO loading particularly at the optimal Cu content of 20 wt%. The 20 wt%CuO/SnO2 sensor showed an excellent response of 1.36⋅105 towards 10 ppm H2S and high H2S selectivity against H2, SO2, CH4 and C2H2 at a low optimum working temperature of 200°C. In addition, the sensor provided fast response and a low detection limit of less than 0.15 ppm. The CuO-SnO2 sensor could therefore be a potential candidate for H2S detection in environmental applications.

scholarly journals Effects of Niobium-Loading on Sulfur Dioxide Gas-Sensing Characteristics of Hydrothermally Prepared Tungsten Oxide Thick Film

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Viruntachar Kruefu ◽  
Anurat Wisitsoraat ◽  
Sukon Phanichphant
Keyword(s):  
Spin Coating ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Sensor Response ◽  
X Ray Diffraction ◽  
Optimal Operating ◽  
Impregnation Process ◽  
X Ray ◽  
Transmission Electron ◽  
Sensing Characteristics

Nb-loaded hexagonal WO3nanorods with 0–1.0 wt% loading levels were successfully synthesized by a simple hydrothermal and impregnation process and characterized for SO2sensing. Nb-loaded WO3sensing films were produced by spin coating on alumina substrate with interdigitated gold electrodes and annealed at 450°C for 3 h in air. Structural characterization by X-ray diffraction, high-resolution transmission electron microscopy, and Brunauer-Emmett-Teller analysis showed that spherical, oval, and rod-like Nb nanoparticles with 5–15 nm mean diameter were uniformly dispersed on hexagonal WO3nanorods with 50–250 nm diameter and 100 nm–5 µm length. It was found that the optimal Nb loading level of 0.5 wt% provides substantial enhancement of SO2response but the response became deteriorated at lower and higher loading levels. The 0.50 wt% Nb-loaded WO3nanorod sensing film exhibits the best SO2sensing performances with a high sensor response of ~10 and a short response time of ~6 seconds to 500 ppm of SO2at a relatively low optimal operating temperature of 250°C. Therefore, Nb loading is an effective mean to improve the SO2gas-sensing performances of hydrothermally prepared WO3nanorods.

scholarly journals Studies on Sensing Properties and Mechanism of CuO Nanoparticles to H2S Gas

Nanomaterials ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 774 ◽  
Author(s):  
Fang Peng ◽  
Yan Sun ◽  
Yue Lu ◽  
Weiwei Yu ◽  
Meiying Ge ◽  
...  
Keyword(s):  
Low Temperature ◽  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Oxidation Mechanism ◽  
Recovery Process ◽  
Cuo Nanoparticles ◽  
Mechanism Analysis ◽  
X Ray ◽  
Enhanced Sensitivity ◽  
Transmission Electron

In this work, the high crystalline copper oxide (CuO) nanoparticles were fabricated by a hydrothermal method, and their structural properties were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The sensing results show that CuO nanoparticles exhibit enhanced sensitivity and good selectivity for hydrogen sulfide (H2S) gas at a low temperature. There are two working mechanisms involved in the H2S sensing based on CuO nanoparticle sensors. They are the H2S oxidation mechanism and the copper sulphide (CuS) formation mechanism, respectively. The two sensing mechanisms collectively enhance the sensor’s response in the H2S sensing process. The Cu–S bonding is stable and cannot break spontaneously at a low temperature. Therefore, the CuS formation inhibits the sensor’s recovery process. Such inhibition gradually enhances as the gas concentration increases from 0.2 ppm to 5 ppm, and it becomes weaker as the operating temperature rises from 40 °C to 250 °C. The XPS results confirmed the CuS formation phenomenon, and the micro Raman spectra demonstrated that the formation of CuS bonding and its decomposition can be effectively triggered by a thermal effect. Gas-sensing mechanism analysis supplied abundant cognition for the H2S sensing phenomena based on CuO materials.

scholarly journals Structural Characterizations of Palladium Clusters Prepared by Polyol Reduction of [PdCl4]2−Ions

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Loredana Schiavo ◽  
Lucrezia Aversa ◽  
Roberta Tatti ◽  
Roberto Verucchi ◽  
Gianfranco Carotenuto
Keyword(s):  
Photoelectron Spectroscopy ◽  
Chemical Properties ◽  
Nucleating Agent ◽  
X Ray Diffraction ◽  
Palladium Clusters ◽  
X Ray ◽  
Transmission Electron ◽  
Hydrogen Technology ◽  
Physical And Chemical

Palladium nanoparticles are of great interest in many industrial fields, ranging from catalysis and hydrogen technology to microelectronics, thanks to their unique physical and chemical properties. In this work, palladium clusters have been prepared by reduction of [PdCl4]2−ions with ethylene glycol, in the presence of poly(N-vinyl-2-pyrrolidone) (PVP) as stabilizer. The stabilizer performs the important role of nucleating agent for the Pd atoms with a fast phase separation, since palladium atoms coordinated to the polymer side-groups are forced at short distances during nucleation. Quasispherical palladium clusters with a diameter of ca. 2.6 nm were obtained by reaction in air at 90°C for 2 hours. An extensive materials characterization by transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and other characterizations (TGA, SEM, EDS-SEM, and UV-Vis) has been performed in order to evaluate the structure and oxidation state of nanopalladium.

scholarly journals Highly Sensitive and Selective Sensing of H2S Gas Using Precipitation and Impregnation-Made CuO/SnO2 Thick Films

2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Pimpan Leangtanom ◽  
Anurat Wisitsoraat ◽  
Kata Jaruwongrangsee ◽  
Narong Chanlek ◽  
Adisorn Tuantranont ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Fast Response ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cu Content ◽  
Transmission Electron ◽  
Highly Sensitive

AbstractIn this work, CuO-loaded tetragonal SnO2 nanoparticles (CuO/SnO2 NPs) were synthesized using precipitation/impregnation methods with varying Cu contents of 0–25 wt% and characterized for H2S detection. The material phase, morphology, chemical composition, and specific surface area of NPs were evaluated using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller analysis. From gas-sensing data, the H2S responses of SnO2 NPs were greatly enhanced by CuO loading particularly at the optimal Cu content of 20 wt%. The 20 wt% CuO/SnO2 sensor showed an excellent response of 1.36 × 105 toward 10 ppm H2S and high H2S selectivity against H2, SO2, CH4, and C2H2 at a low optimum working temperature of 200 °C. In addition, the sensor provided fast response and a low detection limit of less than 0.15 ppm. The CuO–SnO2 sensor could therefore be a potential candidate for H2S detection in environmental applications.

Acetylene Sensing Characteristics of SnO2 Nanowires

2015 ◽  
Vol 1119 ◽  
pp. 132-136
Author(s):  
Bing Wang
Keyword(s):  
Electron Microscopy ◽  
Thermal Evaporation ◽  
Gas Adsorption ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Material ◽  
Transmission Electron ◽  
Mems Technology ◽  
Sensing Characteristics

SnO2 nanowires have been fabricated using thermal evaporation of the mixed powders of SnO2 and active carbon with Au catalysts. The morphology and structure of the prepared nanowires are determined on the basis of field-emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectrometer (EDS), x-ray diffraction (XRD) and transmission electron microscopy (TEM). The comb-shape interdigitating electrode made by MEMS technology is used to auxiliary investigating the gas sensing performance of the synthesized SnO2 nanowires. The SnO2 nanowires have sensing response to acetylene concentration of 1000 ppm under operated temperature of 300°C. The gas sensing mechanism is attributed to the gas adsorption and desorption processes occurring on the surface of the gas sensing material.

Hydrothermal synthesis, characterization and gas sensing of Bi2MoxW1−xO6

2020 ◽  
Vol 13 (06) ◽  
pp. 2051032
Author(s):  
Li Zhang ◽  
Chengwen Song ◽  
Xiaoxing Zhang ◽  
Zhemin Shi ◽  
Jingkun Xiao
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Good Sensitivity ◽  
Good Property ◽  
X Ray ◽  
Transmission Electron ◽  
One Step ◽  
Sensing Application

Bi2MoxW[Formula: see text]O6 microspheres are synthesized by simple one-step hydrothermal method and the morphological characterizations are performed by X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS), BET, scanning electron microscopy (SEM), transmission electron microscopy (TEM). The gas sensing of Bi2WO6, Bi2MoO6 and Bi2MoxW[Formula: see text]O6 is investigated. It can be concluded that the sensor of Bi2MoxW[Formula: see text]O6 has the same good sensitivity as pure Bi2MoO6 and Bi2WO6 to alcohol. It is noteworthy that the operating temperature of Bi2Mo[Formula: see text]W[Formula: see text]O6 is 200∘C which is lower than that of pure Bi2WO6 or Bi2MoO6 (240∘C), so Bi2MoxW[Formula: see text]O6 show its good property for alcohol gas sensing application.

Sign in / Sign up

Export Citation Format

Share Document