scholarly journals Ultrasound Standing Wave-Based Cell-to-liquid Separation for Measuring Viscosity and Aggregation of Blood Sample

Sensors ◽  
2020 ◽  
Vol 20 (8) ◽  
pp. 2284
Author(s):  
Gwangho Kim ◽  
Sanghwa Jeong ◽  
Yang Jun Kang
Keyword(s):  
Mechanical Properties ◽  
Blood Sample ◽  
Present Method ◽  
Ex Vivo ◽  
Ultrasonic Transducer ◽  
Excitation Frequency ◽  
Periodic Pattern ◽  
Blood Samples ◽  
Rbc Aggregation ◽  
Dextran Solution

When quantifying mechanical properties of blood samples flowing in closed fluidic circuits, blood samples are collected at specific intervals. Centrifugal separation is considered as a required procedure for preparing blood samples. However, the use of centrifuge is associated with several issues, including the potential for red blood cell (RBC) lysis, clotting activation, and RBC adhesions in the tube. In this study, an ultrasonic transducer is employed to separate RBCs or diluent from blood sample. The ultrasonic radiation force is much smaller than the centrifugal force acting in centrifuge, it can avoid critical issues occurring under centrifuge. Then, the RBC aggregation and blood viscosity of the blood sample are obtained using the microfluidic technique. According to the numerical results, ultrasonic transducers exhibited a maximum quality factor at an excitation frequency of 2.1 MHz. Periodic pattern of acoustic pressure fields were visualized experimentally as a column mode. The half wavelength obtained was as 0.5 λ = 0.378 ± 0.07 mm. The experimental results agreed with the analytical estimation sufficiently. An acoustic power of 2 W was selected carefully for separating RBCs or diluent from various blood samples (i.e., Hct = 20% ~ 50%; diluent: plasma, 1x phosphate-buffered saline (PBS), and dextran solution). The present method was employed to separate fixed blood samples which tended to stack inside the tube while using the centrifuge. Fixed RBCs were collected easily with an ultrasonic transducer. After various fixed blood samples with different base solutions (i.e., glutaraldehyde solution, 1x PBS, and dextran solution) were prepared using the present method, RBC aggregation and the viscosity of the blood sample are successfully obtained. In the near future, the present method will be integrated into ex vivo or in vitro fluidic circuit for measuring multiple mechanical properties of blood samples for a certain longer period.

scholarly journals Experimental Investigation of Air Compliance Effect on Measurement of Mechanical Properties of Blood Sample Flowing in Microfluidic Channels

Micromachines ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 460
Author(s):  
Yang Jun Kang
Keyword(s):  
Mechanical Properties ◽  
Blood Sample ◽  
Time Constant ◽  
Blood Viscosity ◽  
Temporal Variations ◽  
Microfluidic Channels ◽  
Air Cavity ◽  
Blood Samples ◽  
Blood Flows ◽  
Rbc Aggregation

Air compliance has been used effectively to stabilize fluidic instability resulting from a syringe pump. It has also been employed to measure blood viscosity under constant shearing flows. However, due to a longer time delay, it is difficult to quantify the aggregation of red blood cells (RBCs) or blood viscoelasticity. To quantify the mechanical properties of blood samples (blood viscosity, RBC aggregation, and viscoelasticity) effectively, it is necessary to quantify contributions of air compliance to dynamic blood flows in microfluidic channels. In this study, the effect of air compliance on measurement of blood mechanical properties was experimentally quantified with respect to the air cavity in two driving syringes. Under periodic on–off blood flows, three mechanical properties of blood samples were sequentially obtained by quantifying microscopic image intensity (<I>) and interface (α) in a co-flowing channel. Based on a differential equation derived with a fluid circuit model, the time constant was obtained by analyzing the temporal variations of β = 1/(1–α). According to experimental results, the time constant significantly decreased by securing the air cavity in a reference fluid syringe (~0.1 mL). However, the time constant increased substantially by securing the air cavity in a blood sample syringe (~0.1 mL). Given that the air cavity in the blood sample syringe significantly contributed to delaying transient behaviors of blood flows, it hindered the quantification of RBC aggregation and blood viscoelasticity. In addition, it was impossible to obtain the viscosity and time constant when the blood flow rate was not available. Thus, to measure the three aforementioned mechanical properties of blood samples effectively, the air cavity in the blood sample syringe must be minimized (Vair, R = 0). Concerning the air cavity in the reference fluid syringe, it must be sufficiently secured about Vair, R = 0.1 mL for regulating fluidic instability because it does not affect dynamic blood flows.

scholarly journals Blood Viscoelasticity Measurement Using Interface Variations in Coflowing Streams under Pulsatile Blood Flows

Micromachines ◽  
2020 ◽  
Vol 11 (3) ◽  
pp. 245 ◽  
Author(s):  
Yang Jun Kang
Keyword(s):  
Blood Sample ◽  
Flow Rate ◽  
Present Method ◽  
Experimental Results ◽  
Blood Samples ◽  
Constant Flow Rate ◽  
Blood Flows ◽  
The Status ◽  
Sinusoidal Flow ◽  
Linear Differential

Blood flows in microcirculation are determined by the mechanical properties of blood samples, which have been used to screen the status or progress of diseases. To achieve this, it is necessary to measure the viscoelasticity of blood samples under a pulsatile blood condition. In this study, viscoelasticity measurement is demonstrated by quantifying interface variations in coflowing streams. To demonstrate the present method, a T-shaped microfluidic device is designed to have two inlets (a, b), one outlet (a), two guiding channels (blood sample channel, reference fluid channel), and one coflowing channel. Two syringe pumps are employed to infuse a blood sample at a sinusoidal flow rate. The reference fluid is supplied at a constant flow rate. Using a discrete fluidic circuit model, a first-order linear differential equation for the interface is derived by including two approximate factors (F1 = 1.094, F2 = 1.1087). The viscosity and compliance are derived analytically as viscoelasticity. The experimental results showed that compliance is influenced substantially by the period. The hematocrit and diluent contributed to the varying viscosity and compliance. The viscoelasticity varied substantially for red blood cells fixed with higher concentrations of glutaraldehyde solution. The experimental results showed that the present method has the ability to monitor the viscoelasticity of blood samples under a sinusoidal flow-rate pattern.

Monitoring of r-Hirudin Anticoagulation during Cardiopulmonary Bypass – Assessment of the Whole Blood Ecarin Clotting Time

1997 ◽  
Vol 77 (05) ◽  
pp. 0920-0925 ◽  
Author(s):  
Bernd Pötzsch ◽  
Katharina Madlener ◽  
Christoph Seelig ◽  
Christian F Riess ◽  
Andreas Greinacher ◽  
...  
Keyword(s):  
Cardiopulmonary Bypass ◽  
Whole Blood ◽  
Heart Surgery ◽  
Ex Vivo ◽  
Open Heart Surgery ◽  
Clotting Time ◽  
Blood Samples ◽  
Alternative Approach ◽  
Ecarin Clotting Time

SummaryThe use of recombinant ® hirudin as an anticoagulant in performing extracorporeal circulation systems including cardiopulmonary bypass (CPB) devices requires a specific and easy to handle monitoring system. The usefulness of the celite-induced activated clotting time (ACT) and the activated partial thromboplastin time (APTT) for r-hirudin monitoring has been tested on ex vivo blood samples obtained from eight patients treated with r-hirudin during open heart surgery. The very poor relationship between the prolongation of the ACT and APTT values and the concentration of r-hirudin as measured using a chromogenic factor Ila assay indicates that both assays are not suitable to monitor r-hirudin anticoagulation. As an alternative approach a whole blood clotting assay based on the prothrombin-activating snake venom ecarin has been tested. In vitro experiments using r-hirudin- spiked whole blood samples showed a linear relationship between the concentration of hirudin added and the prolongation of the clotting times up to a concentration of r-hirudin of 4.0 µg/ml. Interassay coefficients (CV) of variation between 2.1% and 5.4% demonstrate the accuracy of the ecarin clotting time (ECT) assay. Differences in the interindividual responsiveness to r-hirudin were analyzed on r-hirudin- spiked blood samples obtained from 50 healthy blood donors. CV- values between 1.8% and 6% measured at r-hirudin concentrations between 0.5 and 4 µg/ml indicate remarkably slight differences in r-hirudin responsiveness. ECT assay results of the ex vivo blood samples linearily correlate (r = 0.79) to the concentration of r-hirudin. Moreover, assay results were not influenced by treatment with aprotinin or heparin. These findings together with the short measuring time with less than 120 seconds warrant the whole blood ECT to be a suitable assay for monitoring of r-hirudin anticoagulation in cardiac surgery.

scholarly journals Development of a blood sample detector for multi-tracer positron emission tomography using gamma spectroscopy

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Carlos Velasco ◽  
Adriana Mota-Cobián ◽  
Jesús Mateo ◽  
Samuel España
Keyword(s):  
Positron Emission Tomography ◽  
Blood Sample ◽  
Pet Imaging ◽  
Spectroscopic Analysis ◽  
Gamma Spectroscopy ◽  
Emission Tomography ◽  
Blood Samples ◽  
Positron Emission

Abstract Background Multi-tracer positron emission tomography (PET) imaging can be accomplished by applying multi-tracer compartment modeling. Recently, a method has been proposed in which the arterial input functions (AIFs) of the multi-tracer PET scan are explicitly derived. For that purpose, a gamma spectroscopic analysis is performed on blood samples manually withdrawn from the patient when at least one of the co-injected tracers is based on a non-pure positron emitter. Alternatively, these blood samples required for the spectroscopic analysis may be obtained and analyzed on site by an automated detection device, thus minimizing analysis time and radiation exposure of the operating personnel. In this work, a new automated blood sample detector based on silicon photomultipliers (SiPMs) for single- and multi-tracer PET imaging is presented, characterized, and tested in vitro and in vivo. Results The detector presented in this work stores and analyzes on-the-fly single and coincidence detected events. A sensitivity of 22.6 cps/(kBq/mL) and 1.7 cps/(kBq/mL) was obtained for single and coincidence events respectively. An energy resolution of 35% full-width-half-maximum (FWHM) at 511 keV and a minimum detectable activity of 0.30 ± 0.08 kBq/mL in single mode were obtained. The in vivo AIFs obtained with the detector show an excellent Pearson’s correlation (r = 0.996, p < 0.0001) with the ones obtained from well counter analysis of discrete blood samples. Moreover, in vitro experiments demonstrate the capability of the detector to apply the gamma spectroscopic analysis on a mixture of 68Ga and 18F and separate the individual signal emitted from each one. Conclusions Characterization and in vivo evaluation under realistic experimental conditions showed that the detector proposed in this work offers excellent sensibility and stability. The device also showed to successfully separate individual signals emitted from a mixture of radioisotopes. Therefore, the blood sample detector presented in this study allows fully automatic AIFs measurements during single- and multi-tracer PET studies.

scholarly journals Predicting chromosome damage in astronauts participating in international space station missions

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Alan Feiveson ◽  
Kerry George ◽  
Mark Shavers ◽  
Maria Moreno-Villanueva ◽  
Ye Zhang ◽  
...  
Keyword(s):  
International Space Station ◽  
Dose Response ◽  
Ex Vivo ◽  
Space Station ◽  
Space Radiation ◽  
Blood Samples ◽  
International Space ◽  
Significant Difference ◽  
Subject Specific

AbstractSpace radiation consists of energetic protons and other heavier ions. During the International Space Station program, chromosome aberrations in lymphocytes of astronauts have been analyzed to estimate received biological doses of space radiation. More specifically, pre-flight blood samples were exposed ex vivo to varying doses of gamma rays, while post-flight blood samples were collected shortly and several months after landing. Here, in a study of 43 crew-missions, we investigated whether individual radiosensitivity, as determined by the ex vivo dose–response of the pre-flight chromosome aberration rate (CAR), contributes to the prediction of the post-flight CAR incurred from the radiation exposure during missions. Random-effects Poisson regression was used to estimate subject-specific radiosensitivities from the preflight dose–response data, which were in turn used to predict post-flight CAR and subject-specific relative biological effectiveness (RBEs) between space radiation and gamma radiation. Covariates age, gender were also considered. Results indicate that there is predictive value in background CAR as well as radiosensitivity determined preflight for explaining individual differences in post-flight CAR over and above that which could be explained by BFO dose alone. The in vivo RBE for space radiation was estimated to be approximately 3 relative to the ex vivo dose response to gamma irradiation. In addition, pre-flight radiosensitivity tended to be higher for individuals having a higher background CAR, suggesting that individuals with greater radiosensitivity can be more sensitive to other environmental stressors encountered in daily life. We also noted that both background CAR and radiosensitivity tend to increase with age, although both are highly variable. Finally, we observed no significant difference between the observed CAR shortly after mission and at > 6 months post-mission.

scholarly journals Microsphere-Based Microfluidic Device for Plasma Separation and Potential Biochemistry Analysis Applications

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 487
Author(s):  
Hongyan Xu ◽  
Zhangying Wu ◽  
Jinan Deng ◽  
Jun Qiu ◽  
Ning Hu ◽  
...  
Keyword(s):  
Blood Sample ◽  
Microfluidic Device ◽  
Biochemical Analysis ◽  
Cost Effective ◽  
Clinical Diagnostics ◽  
Correction Factors ◽  
Separation Device ◽  
Blood Samples ◽  
Plasma Separation ◽  
Blood Biochemical

The development of a simple, portable, and cost-effective plasma separation platform for blood biochemical analysis is of great interest in clinical diagnostics. We represent a plasma separation microfluidic device using microspheres with different sizes as the separation barrier. This plasma separation device, with 18 capillary microchannels, can extract about 3 μL of plasma from a 50 μL blood sample in about 55 min. The effects of evaporation and the microsphere barrier on the plasma biochemical analysis results were studied. Correction factors were applied to compensate for these two effects. The feasibility of the device in plasma biochemical analysis was validated with clinical blood samples.

scholarly journals Quantitative Monitoring of Dynamic Blood Flows Using Coflowing Laminar Streams in a Sensorless Approach

2021 ◽  
Vol 11 (16) ◽  
pp. 7260
Author(s):  
Yang Jun Kang
Keyword(s):  
Blood Flow ◽  
Flow Rate ◽  
Blood Viscosity ◽  
Measurement Errors ◽  
Present Method ◽  
Test Fluid ◽  
Constant Flow Rate ◽  
Rbc Aggregation ◽  
Sinusoidal Flow ◽  
Analytical Expressions

Determination of blood viscosity requires consistent measurement of blood flow rates, which leads to measurement errors and presents several issues when there are continuous changes in hematocrit changes. Instead of blood viscosity, a coflowing channel as a pressure sensor is adopted to quantify the dynamic flow of blood. Information on blood (i.e., hematocrit, flow rate, and viscosity) is not provided in advance. Using a discrete circuit model for the coflowing streams, the analytical expressions for four properties (i.e., pressure, shear stress, and two types of work) are then derived to quantify the flow of the test fluid. The analytical expressions are validated through numerical simulations. To demonstrate the method, the four properties are obtained using the present method by varying the flow patterns (i.e., constant flow rate or sinusoidal flow rate) as well as test fluids (i.e., glycerin solutions and blood). Thereafter, the present method is applied to quantify the dynamic flows of RBC aggregation-enhanced blood with a peristaltic pump, where any information regarding the blood is not specific. The experimental results indicate that the present method can quantify dynamic blood flow consistently, where hematocrit changes continuously over time.

scholarly journals Vibrational Stresses of Damaged Steam Turbine Blades After Renovation Repair

2021 ◽  
Vol 24 (1) ◽  
pp. 42-52
Author(s):  
Mykola H. Shulzhenko ◽  
◽  
Anton S. Olkhovskyi ◽  
Keyword(s):  
Mechanical Properties ◽  
Strain State ◽  
Turbine Blades ◽  
Excitation Frequency ◽  
Physical And Mechanical Properties ◽  
Erosion Damage ◽  
Trailing Edges ◽  
Blade System ◽  
Last Stage ◽  
Maximum Stresses

The last-stage blades of K-1000-60/3000 steam turbines operate in a humid steam environment, which causes erosion damage in the blades and reduction in their residual life. The relevance of this work is related to the need to continue the safe operation of such turbine blades. A number of variants of the finite-element models of individual blades and last-stage blades in the disk-blade systems of the above turbines are considered. Results of the numerical study of the influence of blade part removals in erosion damage zones after renovation repair on the vibration characteristics of individual blades and blades in the disk-blade system are presented. An analysis of the stress-strain state under the conditional load from the steam flow during the forced oscillations of individual blades and blades in the disk-blade system is carried out. The loads are given as evenly distributed and linearly variable on blade surfaces. The dependence of the maximum equivalent vibration stresses on excitation frequency is determined. It is assumed that the physical and mechanical properties of the blade material are preserved (as for the original version) after the renovation repair of blades and processing of their surfaces. There is a significantly greater reduction in the vibration stresses of blades in the disk-blade system than in the stresses of individual blades. Graphs of the dependence of the maximum stresses on excitation frequency both for undamaged individual blades and blades in the disk-blade system after their renovation repair are given. Various variants of blade part removals in areas of blade leading and trailing edges are considered. It is shown that with decreasing chords of blades after renovation repair, frequency regions of increased vibration may appear in lower blade parts. In the lower parts of individual blades and blades in the disk-blade system, the maximum stresses increase in comparison with their values in undamaged blades. With the change in the stress-strain state of rotor blades in comparison with the original version of undamaged blades, the possibility of extending their safe lifetime in case of multi-cycle fatigue is assessed. The safe lifetime of the considered blades with a chord of at least 150 mm after their renovation repair can be extended according to their stresses, if the cyclic symmetry of the disk-blade system is not violated, and the physical and mechanical properties of the material are preserved after the processing of damage removal zones on blade trailing edges.

scholarly journals Ex vivo infiltration of fibroblasts into the tendon deteriorates the mechanical properties of tendon fascicles but not those of tendon bundles

2007 ◽  
Vol 22 (1) ◽  
pp. 120-126 ◽  
Author(s):  
Yasunari Ikema ◽  
Harukazu Tohyama ◽  
Ei Yamamoto ◽  
Fuminori Kanaya ◽  
Kazunori Yasuda
Keyword(s):  
Mechanical Properties ◽  
Ex Vivo
Sign in / Sign up

Export Citation Format

Share Document