scholarly journals 60–700 K CTAT and PTAT Temperature Sensors with 4H-SiC Schottky Diodes

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 942
Author(s):  
Razvan Pascu ◽  
Gheorghe Pristavu ◽  
Gheorghe Brezeanu ◽  
Florin Draghici ◽  
Philippe Godignon ◽  
...  
Keyword(s):  
Low Cost ◽  
Schottky Diodes ◽  
Schottky Contact ◽  
High Sensitivity ◽  
Xrd Analysis ◽  
Absolute Temperature ◽  
Lower Sensitivity ◽  
Readout Circuit ◽  
Sensing Element ◽  
High Performing

A SiC Schottky dual-diode temperature-sensing element, suitable for both complementary variation of VF with absolute temperature (CTAT) and differential proportional to absolute temperature (PTAT) sensors, is demonstrated over 60–700 K, currently the widest range reported. The structure’s layout places the two identical diodes in close, symmetrical proximity. A stable and high-barrier Schottky contact based on Ni, annealed at 750 °C, is used. XRD analysis evinced the even distribution of Ni2Si over the entire Schottky contact area. Forward measurements in the 60–700 K range indicate nearly identical characteristics for the dual-diodes, with only minor inhomogeneity. Our parallel diode (p-diode) model is used to parameterize experimental curves and evaluate sensing performances over this far-reaching domain. High sensitivity, upwards of 2.32 mV/K, is obtained, with satisfactory linearity (R2 reaching 99.80%) for the CTAT sensor, even down to 60 K. The PTAT differential version boasts increased linearity, up to 99.95%. The lower sensitivity is, in this case, compensated by using a high-performing, low-cost readout circuit, leading to a peak 14.91 mV/K, without influencing linearity.

scholarly journals Integrating high-performing electrochemical transducers in lateral flow assay

2021 ◽  
Author(s):  
Antonia Perju ◽  
Nongnoot Wongkaew
Keyword(s):  
High Performance ◽  
Point Of Care ◽  
Low Cost ◽  
High Sensitivity ◽  
Lateral Flow ◽  
Analytical Performance ◽  
Label Free ◽  
High Performing ◽  
Lateral Flow Assays ◽  
Electrochemical Transducers

AbstractLateral flow assays (LFAs) are the best-performing and best-known point-of-care tests worldwide. Over the last decade, they have experienced an increasing interest by researchers towards improving their analytical performance while maintaining their robust assay platform. Commercially, visual and optical detection strategies dominate, but it is especially the research on integrating electrochemical (EC) approaches that may have a chance to significantly improve an LFA’s performance that is needed in order to detect analytes reliably at lower concentrations than currently possible. In fact, EC-LFAs offer advantages in terms of quantitative determination, low-cost, high sensitivity, and even simple, label-free strategies. Here, the various configurations of EC-LFAs published are summarized and critically evaluated. In short, most of them rely on applying conventional transducers, e.g., screen-printed electrode, to ensure reliability of the assay, and additional advances are afforded by the beneficial features of nanomaterials. It is predicted that these will be further implemented in EC-LFAs as high-performance transducers. Considering the low cost of point-of-care devices, it becomes even more important to also identify strategies that efficiently integrate nanomaterials into EC-LFAs in a high-throughput manner while maintaining their favorable analytical performance.

scholarly journals Simulation and performance analysis of Multiple PCS sensors system

2017 ◽  
Vol 20 (2) ◽  
pp. 85
Author(s):  
Pawan Whig ◽  
Syed Naseem Ahmad ◽  
Surinder Kumar
Keyword(s):  
Low Cost ◽  
Reference Electrode ◽  
Oxygen Demand ◽  
High Sensitivity ◽  
Readout Circuit ◽  
Active Components ◽  
Multiple Sensors ◽  
Quality Of Water ◽  
Voltage Signal ◽  
And Performance

In this paper, a novel circuit is presented which overcome a serious limitation found in case of multiple sensors system. In this novel system design only one reference electrode and few active components used that makes the implementation of a low-cost system for the supervision of water quality. Photo Catalytic Sensor (PCS) estimates the parameter BOD (Biological Oxygen Demand) which is generally used to estimate quality of water. The system proposed in this paper involves a balanced bridge approach using few electronic components that provides a correlation in the input-output signals of low-cost sensors. The main reason of employing a readout circuit to PCS circuitry, is the fact that the fluctuation of O2 influences the threshold voltage, which is internal parameter of the FET and can manifest itself as a voltage signal at output but as a function of the trans conductance gain. The trans-conductance is a passive parameter and in order to derive voltage or current signal from its fluctuations the sensor has to be attached to readout circuit. This circuit provides high sensitivity to the changes in percentage of O2 in the solution.

DEVELOPMENT OF ECONOMICAL ASIC FOR PCS FOR WATER QUALITY MONITORING

2014 ◽  
Vol 23 (06) ◽  
pp. 1450079 ◽  
Author(s):  
PAWAN WHIG ◽  
SYED NASEEM AHMAD
Keyword(s):  
Water Quality ◽  
Urban Areas ◽  
Low Cost ◽  
Oxygen Demand ◽  
Computation Time ◽  
High Sensitivity ◽  
Water Quality Monitoring ◽  
Quality Monitoring ◽  
Readout Circuit ◽  
Readout System

In this paper, the design of an ASIC is presented that implement a low-cost system for the supervision of water quality in urban areas or rivers. Photo catalytic sensor (PCS) estimates the parameter biological oxygen demand (BOD) which is generally used to estimate quality of water. The system proposed in this paper involves a simple potentiometric approach that provides a correlation in the input–output signals of low-cost sensors. This approach which is more users friendly and fast in operation is obtained by modeling and optimization of sensor for water quality monitoring. This is to overcome several drawbacks generally found in the previous flow injection analysis method of determining chemical oxygen demand (COD)-like complex designing, nonlinearity and long computation time. The system constitutes a significant cost reduction in the supervision of water quality monitoring. The main reason of employing a readout circuit to PCS circuitry, is the fact that the fluctuation of O 2 influences the threshold voltage, which is internal parameter of the FET and can manifest itself as a voltage signal at output but as a function of the trans-conductance gain. The trans-conductance is a passive parameter and in order to derive voltage or current signal from its fluctuations the sensor has to be attached to readout circuit. This circuit provides high sensitivity to the changes in percentage of O 2 in the solution. In this design simple potentiometric approach with few passive components are used to build a readout circuit. The paper focuses on the electronic implementation of the readout system for the PCS which optimize the circuit performance and increases reliability.

scholarly journals A Stable and Efficient Pt/n-Type Ge Schottky Contact That Uses Low-Cost Carbon Paste Interlayers

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 259
Author(s):  
Pei-Te Lin ◽  
Jia-Wei Chang ◽  
Syuan-Ruei Chang ◽  
Zhong-Kai Li ◽  
Wei-Zhi Chen ◽  
...  
Keyword(s):  
Energy Level ◽  
High Speed ◽  
Schottky Barrier Height ◽  
Low Cost ◽  
Schottky Diodes ◽  
Schottky Contact ◽  
Essential Element ◽  
Carbon Paste ◽  
Ambient Conditions ◽  
Fermi Level Pinning

Ge-based Schottky diodes find applications in high-speed devices. However, Fermi-level pinning is a major issue for the development of Ge-based diodes. This study fabricates a Pt/carbon paste (CP)/Ge Schottky diode using low-cost CP as an interlayer. The Schottky barrier height (ΦB) is 0.65 eV for Pt/CP/n-Ge, which is a higher value than the value of 0.57 eV for conventional Pt/n-Ge. This demonstrates that the CP interlayer has a significant effect. The relevant junction mechanisms are illustrated using feasible energy level band diagrams. This strategy results in greater stability and enables a device to operate for more than 500 h under ambient conditions. This method realizes a highly stable Schottky contact for n-type Ge, which is an essential element of Ge-based high-speed electronics.

Graphene in plastic packages: A low cost construction method for resistive chemical sensors

2012 ◽  
Vol 1407 ◽  
Author(s):  
Silpa Kona ◽  
Cindy K Harnett
Keyword(s):  
Chemical Sensors ◽  
Carbon Materials ◽  
Low Cost ◽  
High Sensitivity ◽  
Cost Effective ◽  
Sensing Element ◽  
Graphene Surface ◽  
Plastic Packages ◽  
Surface Adsorbates ◽  
Gas Molecules

ABSTRACTThe discovery of carbon nanotubes and subsequently graphene has led to an interest in carbon materials as sensing elements due to their unique properties. Graphene is a 2-dimensional material that has a large surface area (~2630 m2g-1) that can be exposed to surface adsorbates from a target gas. This enables studies on the interaction of gas molecules with the graphene surface and resulting changes in its properties, making graphene an excellent sensing element. We present our graphene based sensor with the focus on designing small, cost effective and reliable sensors with high sensitivity towards the target gas, detailing the assembly of graphene/acrylic based devices, their characterization and investigation of their performance as resistive chemical sensors

Schottky diodes based on 2D materials for environmental gas monitoring: a review on emerging trends, recent developments and future perspectives

2021 ◽  
Author(s):  
Minu Mathew ◽  
Chandra Sekhar Rout
Keyword(s):  
Gas Sensing ◽  
2D Materials ◽  
Schottky Diodes ◽  
High Sensitivity ◽  
Future Perspectives ◽  
Working Temperature ◽  
Emerging Trends ◽  
Gas Sensing Properties ◽  
Recent Developments ◽  
Sensitivity And Selectivity

This review details the fundamentals, working principles and recent developments of Schottky junctions based on 2D materials to emphasize their improved gas sensing properties including low working temperature, high sensitivity, and selectivity.

scholarly journals Bimetallic Ni-Based Catalysts for CO2 Methanation: A Review

Nanomaterials ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 28
Author(s):  
Anastasios I. Tsiotsias ◽  
Nikolaos D. Charisiou ◽  
Ioannis V. Yentekakis ◽  
Maria A. Goula
Keyword(s):  
Low Temperature ◽  
Noble Metals ◽  
Recent Progress ◽  
Low Cost ◽  
Alloy Formation ◽  
Co2 Methanation ◽  
High Performing ◽  
Mobile Sources ◽  
Low Dispersion ◽  
Made In

CO2 methanation has recently emerged as a process that targets the reduction in anthropogenic CO2 emissions, via the conversion of CO2 captured from point and mobile sources, as well as H2 produced from renewables into CH4. Ni, among the early transition metals, as well as Ru and Rh, among the noble metals, have been known to be among the most active methanation catalysts, with Ni being favoured due to its low cost and high natural abundance. However, insufficient low-temperature activity, low dispersion and reducibility, as well as nanoparticle sintering are some of the main drawbacks when using Ni-based catalysts. Such problems can be partly overcome via the introduction of a second transition metal (e.g., Fe, Co) or a noble metal (e.g., Ru, Rh, Pt, Pd and Re) in Ni-based catalysts. Through Ni-M alloy formation, or the intricate synergy between two adjacent metallic phases, new high-performing and low-cost methanation catalysts can be obtained. This review summarizes and critically discusses recent progress made in the field of bimetallic Ni-M (M = Fe, Co, Cu, Ru, Rh, Pt, Pd, Re)-based catalyst development for the CO2 methanation reaction.

scholarly journals An Ultrahigh-Sensitivity Graphene Resonant Gyroscope

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1890
Author(s):  
Yang Lu ◽  
Zhan-She Guo ◽  
Shang-Chun Fan
Keyword(s):  
Angular Velocity ◽  
High Sensitivity ◽  
Velocity Variation ◽  
Beam Length ◽  
Sensing Element ◽  
Finite Element Software ◽  
Resonant Beam ◽  
Frequency Output ◽  
Length Width ◽  
Ultrahigh Sensitivity

In this study, a graphene beam was selected as a sensing element and used to form a graphene resonant gyroscope structure with direct frequency output and ultrahigh sensitivity. The structure of the graphene resonator gyroscope was simulated using the ANSYS finite element software, and the influence of the length, width, and thickness of the graphene resonant beam on the angular velocity sensitivity was studied. The simulation results show that the resonant frequency of the graphene resonant beam decreased with increasing the beam length and thickness, while the width had a negligible effect. The fundamental frequency of the designed graphene resonator gyroscope was more than 20 MHz, and the sensitivity of the angular velocity was able to reach 22,990 Hz/°/h. This work is of great significance for applications in environments that require high sensitivity to extremely weak angular velocity variation.

scholarly journals A review on allotropes of carbon and natural filler-reinforced thermomechanical properties of upgraded epoxy hybrid composite

2021 ◽  
Vol 60 (1) ◽  
pp. 237-275
Author(s):  
Krushna Gouda ◽  
Sumit Bhowmik ◽  
Biplab Das
Keyword(s):  
Hybrid Composite ◽  
Low Cost ◽  
Extraction Process ◽  
Thermomechanical Properties ◽  
Neat Epoxy ◽  
Inorganic Filler ◽  
Nonrenewable Resource ◽  
High Performing ◽  
Thermosetting Polymers ◽  
Natural Filler

Abstract The scarcity of nonrenewable resource motivated inclination towards the environmental-friendly novel materials and development of waste natural filler-based hybrid composite is encouraged to fulfill the material demand. Epoxy resins-based composites are high-performing thermosetting polymers and have outstanding blending properties, good machinability, and low cost. Due to these advantages, thermoset plastic is largely used in a broad range of engineering applications; however, thermomechanical properties of neat epoxy are low. Thus, to enhance the thermomechanical properties of epoxy, it is interfaced materials such as graphite, graphene nanoplatelet, boron, carbon fiber, aluminium, silver, etc. Among various substances, graphene has been deliberated as an acceptable novel filler because of its exceptional properties. In addition to inorganic filler inclusion, natural filler/fiber like hemp, sisal, flax, bamboo, jute, etc. can be utilized in a higher percentage as biodegradable material. The present article assisted to improve thermomechanical properties of neat epoxy. This work identifies and addresses (i) processes used for graphene modification; (ii) treatment utilized for enhancing the binding properties of natural filler; (iii) various natural filler extraction process employed; (iv) neat epoxy modification; and (v) influence of different dimensions of fillers.

Low-Cost $K$ -Band Patch Array Antenna for High-Sensitivity EM Sensor

2010 ◽  
Vol 9 ◽  
pp. 982-985 ◽  
Author(s):  
Young-Bae Jung ◽  
Jung Han Choi ◽  
Chang Won Jung
Keyword(s):  
Low Cost ◽  
High Sensitivity ◽  
Array Antenna
Sign in / Sign up

Export Citation Format

Share Document