The impact of channel fin width on electrical characteristics of Si-FinFET

<span>This paper studies the impact of fin width of channel on temperature and electrical characteristics of fin field-effect transistor (FinFET). The simulation tool multi-gate field effect transistor (MuGFET) has been used to examine the FinFET characteristics. Transfer characteristics with various temperatures and channel fin width (W_F=5, 10, 20, 40, and 80 nm) are at first simulated in this study. The results show that the increasing of environmental temperature tends to increase threshold voltage, while the subthreshold swing (SS) and drain-induced barrier lowering (DIBL) rise with rising working temperature. Also, the threshold voltage decreases with increasing channel fin width of transistor, while the SS and DIBL increase with increasing channel fin width of transistor, at minimum channel fin width, the SS is very near to the best and ideal then its value grows and going far from the ideal value with increasing channel fin width. So, according to these conditions, the minimum value as possible of fin width is the preferable one for FinFET with better electrical characteristics.</span>

THE MEMBRANE DISTILLATION ABILITY TO REMOVE CALCIUM ION FROM DAIRY WASTEWATER

In this research the membranes distillation were used to remove calcium ions from heavy sewers at dairy plants in Iraq. This method is easy to operate, easy to manage and has many economic benefits. A chemical treatment was carried out on it using alum as a coagulant, different tests achieved samples before and after passing MD, according to APHA, AWWA, WEF. The results showed that obtained in water treatment trust that has been manufactured and edited according to the characteristics of the water waste the interests of the dairy capacity of this method to remove the calcium ion to a certain extent it is when the concentration reaches the inside of this ion to 1428.57 mg per liter, where to start the composition of hydroxides of calcium responsible for pain. The optimal working temperature ranges from 20-22 ° C and the flow is around 0.66 kg.m-2.h-1, here was the result of a layer of plaster that led to clogged membrane and folding and was stopped for washing and cleaning.

Local chemical fluctuation mediated ultra-sluggish martensitic transformation in high-entropy intermetallics

Superelasticity associated with the martensitic transformation has found a broad range of engineering applications such as low-temperature devices in aerospace industry. Nevertheless, the narrow working temperature range and strong temperature...

Review on Sol-Gel Synthesis of Perovskite and Oxide Nanomaterials

Sol-Gel is a low cost, well-established and flexible synthetic route to produce a wide range of micro- and nanostructures. Small variations in pH, temperature, precursors, time, pressure, atmosphere, among others, can lead to a wide family of compounds that share the same molecular structures. In this work, we present a general review of the synthesis of LaMnO3, SrTiO3, BaTiO3 perovskites and zinc vanadium oxides nanostructures based on Sol-Gel method. We discuss how small changes in the parameters of the synthesis can modify the morphology, shape, size, homogeneity, aggregation, among others, of the products. We also discuss the different precursors, solvents, working temperature, reaction times used throughout the synthesis. In the last section, we present novel uses of Sol-Gel with organic materials with emphasis on carbon-based compounds. All with a perspective to improve the method for future applications in different technological fields.

Flexible Low-Temperature Ammonia Gas Sensor Based on Reduced Graphene Oxide and Molybdenum Disulfide

Owing to harsh working environments and complex industrial requirements, traditional gas sensors are prone to deformation damage, possess a limited detection range, require a high working temperature, and display low reliability, thereby necessitating the development of flexible and low-temperature gas sensors. In this study, we developed a low-temperature polyimide (PI)-based flexible gas sensor comprising a reduced graphene oxide (rGO)/MoS2 composite. The micro-electro-mechanical system technology was used to fabricate Au electrodes on a flexible PI sheet to form a “sandwiched” sensor structure. The rGO/MoS2 composites were synthesized via a one-step hydrothermal method. The gas-sensing response was the highest for the composite comprising 10% rGO. The structure of this material was characterized, and a PI-based flexible gas sensor comprising rGO/MoS2 was fabricated. The optimal working temperature of the sensor was 141 °C, and its response-recovery time was significantly short upon exposure to 50–1500 ppm NH3. Thus, this sensor exhibited high selectivity and a wide NH3 detection range. Furthermore, it possessed the advantages of low power consumption, a short response-recovery time, a low working temperature, flexibility, and variability. Our findings provide a new framework for the development of pollutant sensors that can be utilized in an industrial environment.

Numerical evaluation of expansion loops for pipe subjected to thermal displacements

The thermal expansion can lead to the high stress on the pipe. The problem can be overcome using expansion loops in a certain length depending on the material’s elastic modulus, diameter, the amount of expansion, and the pipe’s allowable stresses. Currently, there is no exact definition for the dimension of expansion loops design both for loop width (W) and loop footing height (H) sizes. In this study, expansion loops were investigated with using ratio of width and height (W/H) variations to understand pipe stress occurring on the expansion loops and the expansion loops’ safety factor. Relationship between non dimensional stress on the expansion loop pipe was studied numerically by finite element software on several working temperatures of 400oF, 500oF, 600oF, and 700oF. It can be found that stress occurring on the pipes increases as the increases of W/H of the expansion loops and results in a lower safety factor. The safety factor of the expansion loops pipe has a value of 1 when the ratio of loop width and loop footing height (W/H) value was 1.2 for a 16-inch diameter pipe. Stress occurring on the pipe increases with the increase of the working temperature. Expansion loops pipe designed for 400oF can still work well to handle thermal extension pipe occurring on 500oF.

Enhancing the magnetocaloric response of high-entropy metallic-glass by microstructural control

Non-equiatomic high-entropy alloys (HEAs), the second-generation multi-phase HEAs, have been recently reported with outstanding properties that surpass the typical limits of conventional alloys and/or the first-generation equiatomic single-phase HEAs. For magnetocaloric HEAs, non-equiatomic (Gd36Tb20Co20Al24)100−xFex microwires, with Curie temperatures up to 108 K, overcome the typical low temperature limit of rare-earth-containing HEAs (which typically concentrate lower than around 60 K). For alloys with x = 2 and 3, they possess some nanocrystals, though very minor, which offers a widening in the Curie temperature distribution. In this work, we further optimize the magnetocaloric responses of x = 3 microwires by microstructural control using the current annealing technique. With this processing method, the precipitation of nanocrystals within the amorphous matrix leads to a phase compositional difference in the microwires. The multi-phase character leads to challenges in rescaling the magnetocaloric curves, which is overcome by using two reference temperatures during the scaling procedure. The phase composition difference increases with increasing current density, whereby within a certain range, the working temperature span broadens and simultaneously offers relative cooling power values that are at least 2-fold larger than many reported conventional magnetocaloric alloys, both single amorphous phase or multi-phase character (amorphous and nanocrystalline). Among the amorphous rare-earth-containing HEAs, our work increases the working temperature beyond the typical <60 K limit while maintaining a comparable magnetocaloric effect. This demonstrates that microstructural control is a feasible way, in addition to appropriate compositional design selection, to optimize the magnetocaloric effect of HEAs.

Significant effect of SDS on the optimum operating temperature of ZnO nanosheets gas-sensitive materials

Many methods have been used to reduce the operational energy consumption of ZnO gas-sensitive material effectively. In this paper, different morphologies of ZnO nanomaterials are respectively prepared in the anionic hydrophilic surfactant sodium lauryl sulfate (SDS) with different concentrations as soft templates by hydrothermal method. The influence of SDS concentrations is investigated on the morphology of materials under the conditions of a weak alkali environment with the same pH, and their gas sensitivity after annealing with the same temperature and time. The morphologies and phase structures of all samples are characterized by FESEM and XRD, and their gas-sensitive properties are analyzed by CGS-1TP. Interestingly, the experimental results show that the optimal working temperature of ZnO gas-sensitive materials containing low concentration SDS is reduced by nearly 55% than that of containing 10 times this concentration, and its sensitivity is also slightly improved. The possible mechanism by which the SDS concentration affects the gas sensitivity of the material is also proposed.

Preparation of Nanostructured SnO2-NiO Composite Semiconductor for Gas Sensor Applications

Electro spinning technology combined with chemical precipitation method and high-temperature calcination was used to prepare SnO2-NiO composite semiconductor nanofibers with different Sn content. Scanning electron microscope (SEM), X-ray diffractometer (XRD) and energy dispersive X-ray spectrometer (EDS) were used to characterize the morphology, structure and content of various elements of the sample. Using ethanol as the target gas, the gas sensing properties of SnO2-NiO nanofibers and the influence of Sn content on the gas sensing properties of composite nanofibers were explored. The research results show that SnO2-NiO composite nanofibers have a three-dimensional network structure, and the SnO2 composite can significantly enhance the gas sensitivity of NiO nanofibers. With increase of SnO2 content, the response sensitivity of composite fibers to ethanol gas increases, and the response sensitivity of composite nanofibers with the highest response to ethanol gas with a volume fraction of 100×10-6 at the optimal working temperature of 160℃ are13.4;It is 8.38 times the maximum response sensitivity of NiO nanofibers. Compared with the common ethanol gas sensor MQ-3 on the market, SnO2-NiO composite nanofibers have a lower optimal working temperature and higher response sensitivity, which has certain practical application value

Significance of Anisotropic Thermal Expansion in High Speed Electric Machines Employing NdFeB Permanent Magnets

Many high speed applications employ a surface permanent magnet (PM) machine topology with a retaining sleeve due to its robustness and ability to achieve high overall peripheral speeds as well as efficiencies. One often overlooked feature in the mechanical design of such machines, which has not achieved sufficient attention to date is the anisotropic thermal expansion of rare earth magnets, the degree of which varies for different magnet technologies. This paper investigates the effects of the aforementioned on the mechanical design of a high speed PM spindle machine with NdFeB magnets. The maximum allowable interference is found to be limited by the working temperature of the magnets while the minimum required interference is increased due to their anisotropic thermal expansion. Based on this, appropriate conditions are formulated to integrate a Neodymium Iron Boron (NdFeB) PM in high speed rotors. These modifications considering the shaft together with the magnet anisotropic thermal expansion are included in a proposed rotor design and validated using simulations in ANSYS mechanical environment.