scholarly journals A New Hybrid Sensitive PANI/SWCNT/Ferrocene-Based Layer for a Wearable CO Sensor

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1801
Author(s):  
Mihaela Savin ◽  
Carmen-Marinela Mihailescu ◽  
Viorel Avramescu ◽  
Silviu Dinulescu ◽  
Bogdan Firtat ◽  
...  
Keyword(s):  
Electrochemical Impedance ◽  
Wearable Sensor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Concentration ◽  
Good Potential ◽  
Co Sensor ◽  
Co Detection ◽  
Conductive Properties ◽  
Walled Carbon Nanotubes

Developing a sensing layer with high electroactive properties is an important aspect for proper functionality of a wearable sensor. The polymeric nanocomposite material obtained by a simple electropolymerization on gold interdigitated electrodes (IDEs) can be optimized to have suitable conductive properties to be used with direct current (DC) measurements. A new layer based on polyaniline:poly(4-styrenesulfonate) (PANI:PSS)/single-walled carbon nanotubes (SWCNT)/ferrocene (Fc) was electrosynthesized and deposed on interdigital transducers (IDT) and was characterized in detail using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoemission spectroscopy (XPS), and X-ray diffraction (XRD). The sensor characteristics of the material towards carbon monoxide (CO) in the concentration range of 10–300 ppm were examined, showing a minimal relative humidity interference of only 1% and an increase of sensitivity with the increase of CO concentration. Humidity interference could be controlled by the number of CV cycles when a compact layer was formed and the addition of Fc played an important role in the decrease of humidity. The results for CO detection can be substantially improved by optimizing the number of deposition cycles and enhancing the Fc concentration. The material was developed for selective detection of CO in real environmental conditions and shows good potential for use in a wearable sensor.

Effect of Zn Content on Structure, Roughness and Corrosion Behavior of Zn-Ni Alloys

2019 ◽  
Vol 17 (17) ◽  
pp. 17-22
Author(s):  
Hayette Faid
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Stripping Voltammetry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Alloys ◽  
Sulfate Bath ◽  
Zn Content ◽  
Polarization Test ◽  
Δ Phase

AbstractIn this work, Zn-Ni alloys have been deposited on steel from sulfate bath, by electrodeposition method. The effect of Zn content on deposits properties was studied by cyclic voltammetry (CV), chronoaperometry (CA), linear stripping voltammetry (ALSV) and diffraction (XRD) and scanning electronic microscopy (SEM). The corrosion behavior in 3.5 wt. NaCl solution was examined using anodic polarization test and electrochemical impedance spectroscopy. X-ray diffraction of show that Zn-Ni alloys structure is composed of δ phase and γ phase, which increase with the decrease of Zn content in deposits. Results show that deposits obtained from bath less Zn2+ concentration exhibited better corrosion resistance.

Characterizations of Synthetic 8mol% YSZ with Comparison to 3mol %YSZ for HT-SOFC

2020 ◽  
Vol 38 (4A) ◽  
pp. 491-500
Author(s):  
Abeer F. Al-Attar ◽  
Saad B. H. Farid ◽  
Fadhil A. Hashim
Keyword(s):  
Ionic Conductivity ◽  
Electrochemical Impedance ◽  
Structural Information ◽  
Impedance Analysis ◽  
High Energy ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Powder Morphology ◽  
X Ray

In this work, Yttria (Y2O3) was successfully doped into tetragonal 3mol% yttria stabilized Zirconia (3YSZ) by high energy-mechanical milling to synthesize 8mol% yttria stabilized Zirconia (8YSZ) used as an electrolyte for high temperature solid oxide fuel cells (HT-SOFC). This work aims to evaluate the densification and ionic conductivity of the sintered electrolytes at 1650°C. The bulk density was measured according to ASTM C373-17. The powder morphology and the microstructure of the sintered electrolytes were analyzed via Field Emission Scanning Electron Microscopy (FESEM). The chemical analysis was obtained with Energy-dispersive X-ray spectroscopy (EDS). Also, X-ray diffraction (XRD) was used to obtain structural information of the starting materials and the sintered electrolytes. The ionic conductivity was obtained through electrochemical impedance spectroscopy (EIS) in the air as a function of temperatures at a frequency range of 100(mHz)-100(kHz). It is found that the 3YSZ has a higher density than the 8YSZ. The impedance analysis showed that the ionic conductivity of the prepared 8YSZ at 800°C is0.906 (S.cm) and it was 0.214(S.cm) of the 3YSZ. Besides, 8YSZ has a lower activation energy 0.774(eV) than that of the 3YSZ 0.901(eV). Thus, the prepared 8YSZ can be nominated as an electrolyte for the HT-SOFC.

scholarly journals Effect of Molybdenum Content on the Corrosion and Microstructure of Low-Ni, Co-Free Maraging Steels

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 852
Author(s):  
Asiful H. Seikh ◽  
Hossam Halfa ◽  
Mahmoud S. Soliman
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Microstructural Analysis ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Alloying Element ◽  
X Ray ◽  
Maraging Steels ◽  
Eds Analysis ◽  
Electroslag Refining

Molybdenum (Mo) is an important alloying element in maraging steels. In this study, we altered the Mo concentration during the production of four cobalt-free maraging steels using an electroslag refining process. The microstructure of the four forged maraging steels was evaluated to examine phase contents by optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. Additionally, we assessed the corrosion resistance of the newly developed alloys in 3.5% NaCl solution and 1 M H2SO4 solution through potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Furthermore, we performed SEM and energy-dispersive spectroscopy (EDS) analysis after corrosion to assess changes in microstructure and Raman spectroscopy to identify the presence of phases on the electrode surface. The microstructural analysis shows that the formation of retained austenite increases with increasing Mo concentrations. It is found from corrosion study that increasing Mo concentration up to 4.6% increased the corrosion resistance of the steel. However, further increase in Mo concentration reduces the corrosion resistance.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Structure and Electrochemical Behavior of Plasma-Sprayed LSGM Electrolyte Films

2002 ◽  
Vol 756 ◽  
Author(s):  
H. Zhang ◽  
X. Ma ◽  
J. Dai ◽  
S. Hui ◽  
J. Roth ◽  
...  
Keyword(s):  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
Amorphous Structure ◽  
Solid Oxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spray Process ◽  
Plasma Spray Process ◽  
Electrolyte Film ◽  
Plasma Sprayed

ABSTRACTAn intermediate temperature solid oxide fuel cell (SOFC) electrolyte film of La0.8Sr 0.2Ga0.8Mg0.2O2.8 (LSGM) was fabricated using a plasma spray process. The microstructure and phase were investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical behavior of the thermal sprayed LSGM film was investigated using electrochemical impedance spectroscopy (EIS). The study indicates that thermal spray can deposit a dense LSGM layer. It was found that the rapid cooling in the thermal process led to an amorphous or poor crystalline LSGM deposited layer. This amorphous structure has a significant effect on the performance of the cell. Crystallization of the deposited LSGM layer was observed during annealing between 500–600 °C. After annealing at 800 °C, the ionic conductivity of the sprayed LSGM layer can reach the same level as that of the sintered LSGM.

scholarly journals Electroless Deposition of Cu-SWCNT Composites

2019 ◽  
Vol 5 (4) ◽  
pp. 61 ◽  
Author(s):  
Raja ◽  
Esquenazi ◽  
Jones ◽  
Li ◽  
Brinson ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Electroless Deposition ◽  
Reaction Times ◽  
Phase Identification ◽  
X Ray Diffraction ◽  
Copper Surfaces ◽  
X Ray ◽  
Dispersing Agent ◽  
Defect Sites ◽  
Walled Carbon Nanotubes

In this work, as-received HiPCO single walled carbon nanotubes (SWCNTs) are incorporated in a controllable manner at various concentrations into Cu-SWCNT composites via electroless plating, by varying the related reaction times, with polyethylene glycol (PEG) used as a dispersing agent. The resultant samples were analyzed using scanning electron microscopy (SEM) for morphology assessment, energy dispersive X-ray analysis (EDX) and X-ray photoelectron spectroscopy (XPS) for elemental analysis, X-ray diffraction (XRD) for the assessment of crystal phase identification, and Raman spectroscopy for the confirmation of the presence of the incorporated SWCNTs. The Cu-SWCNT composites were found to contain carbon, catalytic iron (associated with the raw, as-received SWCNTs), oxygen, and copper; the latter was found to be inversely proportional to carbon and iron contents. The oxygen (associated with both the SWCNT defect sites and oxidized copper surfaces) remained more or less constant regardless of the proportion of SWCNTs in the composites. The Raman IG:ID ratio remains within the experimental error constant, indicating that the electroless deposition does not have a deleterious effect on the SWCNTs. At short deposition times, SEM revealed a relatively dense structure comprising a distinctive fibrous morphology, suggestive of an underlying SWCNT substrate coated with copper; however, with increasing deposition, a more porous morphology is observed. The size of the granular particles increases up until 10 min of reaction, after which time it remains unchanged.

scholarly journals Χαρακτηρισμός πολυμερικών επιστρώσεων με νανοπερίεκτες σε μέταλλα για την προστασία τους από διάβρωση σε θαλάσσιο περιβάλλον

2012 ◽  
Author(s):  
Ανδρόνικος Μπαλάσκας
Keyword(s):  
Electrochemical Impedance Spectroscopy ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Open Circuit ◽  
X Ray Diffraction ◽  
X Ray ◽  
Organically Modified Silicates ◽  
Organically Modified ◽  
Ft Ir ◽  
Scanningelectron Microscopy

Υβριδικές επιστρώσεις οργανικά τροποποιημένων πυριτικών ενώσεων και εποξειδικώνρητινών (Organically Modified Silicates, ORMOSILs – epoxy) εφαρμόστηκαν στο κράμααργιλίου 2024-Τ3 και σε γαλβανισμένο χάλυβα σε υψηλές θερμοκρασίες (Hot Dip GalvanizedSteel, HDGS) προκειμένου αυτές να προστατεύσουν τα υποστρώματα από τη διάβρωση. Για τηνβελτίωση της αντοχής των επιστρώσεων στην διάβρωση ενσωματώθηκαν στην πολυμερικήμήτρα νανοπεριέκτες από μολυβδαινικό δημήτριο (CeMo) και οξείδιο του τιτανίου (TiO2),καθώς και pH-ευαίσθητα οργανικά νανοδοχεία πληρωμένα με τους αναστολείς διάβρωσης 2-μερκαπτοβενζοθειαζόλιο, 8-υδροξυκινολίνη, 1H-βενζοτριαζολο-4-σουλφονικό οξύ καιεξαφλουοροτιτανικό οξύ.Οι υβριδικές επιστρώσεις εφαρμόστηκαν στο υπόστρωμα με τη διαδικασία εμβάπτισης.Η μορφολογία των επιστρώσεων εξετάστηκε με ηλεκτρονική μικροσκοπία σάρωσης (ScanningElectron Microscopy (SEM)). Η σύνθεση και η δομή τους μελετήθηκε με υπέρυθρηΦασματοσκοπία μετασχηματισμού Fourier (FT-IR) και με μικροανάλυση με φθορισμομετρίαακτίνων Χ (Energy Dispersive X-Ray Analysis (EDX)). H ηλεκτροχημική φασματοσκοπίασύνθετης αντίστασης (Electrochemical Impedance Spectroscopy, EIS), η dc-πόλωση (dcpolarization)και η μέτριση ανοικτού δυναμικού (open circuit potential, OCP) χρησιμοποιήθηκανγια την αξιολόγηση των αντι-διαβρωτικών ιδιοτήτων των επιστρώσεων. Τα αποτελέσματαέδειξαν ότι οι επιστρώσεις με πληρωμένα νανοδοχεία έχουν αυξημένες αντιδιαβρωτικέςιδιότητες συγκριτικά με τις υπόλοιπες επιστρώσεις εμφανίζοντας και ιδιότητες αυτο-θεραπείας.Τέλος, συντέθηκαν νανόσφαιρες οξειδίου του χαλκού (Cu2O), οι οποίεςχαρακτηρίστηκαν με SEM, ηλεκτρονική μικροσκοπία διερχόμενης δέσμης (ΤransmissionΕlectron Μicroscopy (TEM)) και περίθλαση ακτίνων Χ (X ray Diffraction (XRD)). Οινανόσφαιρες στη συνέχεια πληρώθηκαν με ουσίες που δρουν ως βιοκτόνα και ενσωματώθηκανσε βαφές εμπορίου και σε επιστρώσεις βασισμένες σε εποξειδικές ενώσεις και μελετήθηκε ηδράση τους ως αντιαποθετικά αντιδραστήρια. Τα αποτελέσματα έδειξαν ότι οι επιστρώσεις μεπληρωμένες νανόσφαιρες Cu2O είχαν μεγαλύτερη αποτελεσματικότητα σε σύγκριση με τιςβαφές εμπορίου με βιοκτόνα μετά από έκθεση σε θαλάσσιο περιβάλλον.

Effect of Zirconium Oxide Reinforcement on Microstructural, Electrochemical and Mechanical Properties of TiNi Alloy Produced Via Powder Metallurgy Route

2021 ◽  
pp. 1-22
Author(s):  
Syed Abbas Raza ◽  
Muhammad Imran Khan ◽  
Muhammad Ramzan Abdul karim ◽  
Rashid Ali ◽  
Muhammad Umair Naseer ◽  
...  
Keyword(s):  
Electrochemical Impedance ◽  
Passive Layer ◽  
Charge Transfer Resistance ◽  
Tini Alloy ◽  
X Ray Diffraction ◽  
Zro2 Content ◽  
Transfer Resistance ◽  
X Ray ◽  
Conventional Sintering ◽  
Layer Resistance

Abstract Equiatomic TiNi alloy composites, reinforced with 0, 5, 10 and 15 vol. % ZrO2, were synthesized using conventional sintering approach. Equiatomic TiNi pre-alloyed powder and ZrO2 powder were mixed in planetary ball mill for 6 hours followed by cold compaction and pressure-less sintering, respectively. The sintered density was found to vary inversely with the addition of ZrO2 content. The X-Ray diffraction spectra have shown the formation of multiple-phases which were resulted from the decomposition of the B19'and B2 phases of the equiatomic TiNi alloy due to the addition of ZrO2 and higher diffusion rate of Ni than that of Ti in the alloy composite. An increase in hardness was noted due to the addition of ZrO2, measured by micro and nanoindentation techniques. Potentiodynamic polarization scan revealed a 10% decrease in the corrosion rate of the composite containing 10 vol. % ZrO2. Electrochemical impedance spectroscopy results indicated an increase in passive layer resistance (Rcoat) due to the increase in charge transfer resistance (Rct) caused by the reduced leaching of ions from the surface.

scholarly journals Effect of Graphene Oxide Concentration in Electrolyte on Corrosion Behavior of Electrodeposited Zn–Electrochemical Reduction Graphene Composite Coatings

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 758 ◽  
Author(s):  
Yang ◽  
Zhang ◽  
Wang ◽  
Wang ◽  
Chen ◽  
...  
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Laser Raman Spectroscopy ◽  
304 Stainless Steel ◽  
Sulfate Electrolyte ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tafel Polarization ◽  
Laser Raman

Pure Zn and Zn–ERGO composite coatings were prepared by direct current electrodeposition on 304 stainless steel. Samples were characterized by X-ray diffraction (XRD), scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM/EDS), and laser Raman spectroscopy (Raman). Results obtained have shown that the concentration of GO sheets in zinc sulfate electrolyte has an important effect on the preferred crystal orientation and the surface morphology of Zn–ERGO composite coatings. A study of the corrosion behavior of the coatings by Tafel polarization and electrochemical impedance spectroscopic (EIS) methods leads to the conclusion that the Zn-1.0 g/L ERGO composite coating possesses the best corrosion resistance compared to the pure Zn coating and other composite coatings in this study.

scholarly journals Corrosion Inhibition of Mild Steel by Poly(butylene succinate)-L-histidine Extended with 1,6-diisocynatohexane Polymer Composite in 1 M HCl

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
M. G. Tsoeunyane ◽  
M. E. Makhatha ◽  
O. A. Arotiba
Keyword(s):  
Mild Steel ◽  
Corrosion Inhibition ◽  
Polymer Composite ◽  
Electrochemical Impedance ◽  
Condensation Polymerization ◽  
X Ray Diffraction ◽  
Butylene Succinate ◽  
X Ray ◽  
Atomic Force ◽  
Corrosion Inhibition Efficiency

The ecofriendly poly(butylene succinate) extended with 1,6-diisocynatohexane composted with L-histidine (PBSLH) polymer composite was synthesized by condensation polymerization. The polymer composite was characterized by Fourier transform infrared (FTIR), X-ray diffraction (XRD), and scanning electron microscope (SEM-EDX). The inhibition action of the polymer composite was investigated by conventional weight loss, potentiodynamic polarization, variable amplitude micro (VASP), and electrochemical impedance spectroscopy (EIS). The maximum corrosion inhibition efficiency of 78 % was obtained at concentration level of 600 ppm. The results revealed PBSLH as a mixed type corrosion inhibitor. The thermodynamic and kinetic parameters also revealed adsorption of PBSLH on to mild surface as exothermic and the adsorption was conformed to Langmuir model. The morphology of mild steel coupons was investigated by SEM and atomic force microscope (AFM) and the results showed PBSLH to have inhibited corrosion on mild steel in 1 M HCL.

Sign in / Sign up

Export Citation Format

Share Document