scholarly journals Investigation of the Wind-Induced Airflow Pattern Near the Thies LPM Precipitation Gauge

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4880
Author(s):  
Enrico Chinchella ◽  
Arianna Cauteruccio ◽  
Mattia Stagnaro ◽  
Luca G. Lanza
Keyword(s):  
Navier Stokes ◽  
Strong Wind ◽  
Simulation Framework ◽  
Airflow Velocity ◽  
Airflow Pattern ◽  
Recirculating Flow ◽  
Sst Turbulence Model ◽  
Computational Fluid Dynamics Cfd ◽  
Precipitation Gauge ◽  
The Ideal

The airflow velocity pattern generated by a widely used non-catching precipitation gauge (the Thies laser precipitation monitor or LPM) when immersed in a wind field is investigated using computational fluid dynamics (CFD). The simulation numerically solves the unsteady Reynolds-averaged Navier–Stokes (URANS) equations and the setup is validated against dedicated wind tunnel measurements. The adopted k-ω shear stress transport (SST) turbulence model closely reproduces the flow pattern generated by the complex, non-axisymmetric outer geometry of the instrument. The airflow pattern near the measuring area varies with the wind direction, the most intense recirculating flow and turbulence being observed when the wind blows from the back of the instrument. Quantitative parameters are used to discuss the magnitude of the airflow perturbations with respect to the ideal configuration where the instrument is transparent to the wind. The generated airflow pattern is expected to induce some bias in operational measurements, especially in strong wind conditions. The proposed numerical simulation framework provides a basis to develop correction curves for the wind-induced bias of non-catching gauges, as a function of the undisturbed wind speed and direction.

scholarly journals Snow Particle Collection Efficiency and Adjustment Curves for the Hotplate© Precipitation Gauge

2021 ◽  
Author(s):  
Arianna Cauteruccio ◽  
Enrico Chinchella ◽  
Mattia Stagnaro ◽  
Luca G. Lanza
Keyword(s):  
Wind Speed ◽  
Bluff Body ◽  
Stokes Equations ◽  
Collection Efficiency ◽  
Navier Stokes ◽  
Strong Wind ◽  
Navier Stokes Equations ◽  
Relevant Role ◽  
Tracking Model ◽  
Precipitation Gauge

AbstractThe hotplate precipitation gauge operates by means of a thermodynamic principle. It is composed by a small size disk with two thin aluminium heated plates on the upper and lower faces. Each plate has three concentric rings to prevent the hydrometeors from sliding off in strong wind. As for the more widely used tipping-bucket and weighing gauges, measurements are affected by the wind-induced bias due to the bluff-body aerodynamics of the instrument outer shape. Unsteady Reynolds-Averaged Navier-Stokes equations were numerically solved, using a k-ω shear stress transport closure model, to simulate the aerodynamic influence of the gauge body on the airflow. Wind tunnel tests were conducted to validate simulation results. Solid particle trajectories were modelled using a Lagrangian Particle Tracking model to evaluate the influence of the airflow modification on the ability of the instrument to collect the incoming hydrometeors. A suitable parameterization of the particle size distribution, as a function of the snowfall intensity, was employed to calculate the Collection Efficiency (CE) under different wind conditions. Results reveal a relevant role of the three rings in enhancing the collection performance of the gauge. Below 7.5 m s-1, the CE curves linearly decrease with increasing the wind speed, while beyond that threshold, the blocking caused by the rings counter effects the aerodynamic induced undercatch, and the CE curves quadratically increase with the wind speed. At high wind speed, the undercatch vanishes and the instrument exhibits a rapidly increasing overcatch. For operational purposes, adjustment curves were formulated as a function of the wind speed and the measured snowfall intensity.

scholarly journals Design-Assisted of Pitching Aerofoils through Enhanced Identification of Coherent Flow Structures

Designs ◽  
2021 ◽  
Vol 5 (1) ◽  
pp. 11 ◽  
Author(s):  
Filippo Avanzi ◽  
Francesco De Vanna ◽  
Yin Ruan ◽  
Ernesto Benini
Keyword(s):  
Pressure Field ◽  
Navier Stokes ◽  
Flow Structures ◽  
Coupled Modes ◽  
Spectral Reconstruction ◽  
Sst Turbulence Model ◽  
Coherent Flow Structures ◽  
Highly Correlated ◽  
Naca 0012 ◽  
Proper Orthogonal

This study discusses a general framework to identify the unsteady features of a flow past an oscillating aerofoil in deep dynamic stall conditions. In particular, the work aims at demonstrating the advantages for the design process of the Spectral Proper Orthogonal Decomposition in accurately producing reliable reduced models of CFD systems and comparing this technique with standard snapshot-based models. Reynolds-Averaged Navier-Stokes system of equations, coupled with k−ω SST turbulence model, is used to produce the dataset, the latter consisting of a two-dimensional NACA 0012 aerofoil in the pitching motion. Modal analysis is performed on both velocity and pressure fields showing that, for vectored values, a proper tuning of the filtering process allows for better results compared to snapshot formulations and extract highly correlated coherent flow structures otherwise undetected. Wider filters, in particular, produce enhanced coherence without affecting the typical frequency response of the coupled modes. Conversely, the pressure field decomposition is drastically affected by the windowing properties. In conclusion, the low-order spectral reconstruction of the pressure field allows for an excellent prediction of aerodynamic loads. Moreover, the analysis shows that snapshot-based models better perform on the CFD values during the pitching cycle, while spectral-based methods better fit the loads’ fluctuations.

Computational Fluid Dynamic Using Parallel Loop of Multi-Cores Processor

2014 ◽  
Vol 493 ◽  
pp. 80-85 ◽  
Author(s):  
C.L Siow ◽  
Jaswar ◽  
Efi Afrizal
Keyword(s):  
Fluid Flow ◽  
Early Stage ◽  
Fluid Dynamic ◽  
Visual Basic ◽  
Computer Hardware ◽  
Navier Stokes ◽  
Computer Memory ◽  
Large Size ◽  
Computational Fluid Dynamics Cfd ◽  
Reynolds Average

Computational Fluid Dynamics (CFD) software is often used to study fluid flow and structures motion in fluids. The CFD normally requires large size of arrays and computer memory and then caused long execution time. However, Innovation of computer hardware such as multi-cores processor provides an alternative solution to improve this programming performance. This paper discussed loop parallelize multi-cores processor for optimization of sequential looping CFD code. This loop parallelize CFD was achieved by applying multi-tasking or multi-threading code into the original CFD code which was developed by one of the authors. The CFD code was developed based on Reynolds Average Navier-Stokes (RANS) method. The new CFD code program was developed using Microsoft Visual Basic (VB) programming language. In the early stage, the whole CFD code was constructed in a sequential flow before it is modified to parallel flow by using VBs multi-threading library. In the comparison, fluid flow around the hull of round-shaped FPSO was selected to compare the performance of both the programming codes. Besides, executed results of this self-developed code such as pressure distribution around the hull were also presented in this paper.

Analysis of Hydrodynamic Characteristics in the Process of Autonomous Underwater Vehicle Docking

2015 ◽  
Author(s):  
Xiaoxu Du ◽  
Huan Wang
Keyword(s):  
Drag Coefficient ◽  
Autonomous Underwater Vehicle ◽  
Simple Algorithm ◽  
Underwater Vehicle ◽  
Navier Stokes ◽  
Hydrodynamic Characteristics ◽  
Successful Operation ◽  
Underwater Docking ◽  
Computational Fluid Dynamics Cfd ◽  
Volume Method

The successful operation of an Autonomous Underwater Vehicle (AUV) requires the capability to return to a dock. A number of underwater docking technologies have been proposed and tested in the past. The docking allows the AUV to recharge its batteries, download data and upload new instructions, which is helpful to improve the working time and efficiency. During the underwater docking process, unsteady hydrodynamic interference occurs between the docking device and an AUV. To ensure a successful docking, it is very important that the underwater docking hydrodynamics of AUV is understood. In this paper, numerical simulations based on the computational fluid dynamics (CFD) solutions were carried out for a 1.85m long AUV with maximum 0.2 m in diameter during the docking process. The two-dimensional AUV model without fin and rudder was used in the simulation. The mathematical model based on the Reynolds-averaged Navier-Stokes (RANS) equations was established. The finite volume method (FVM) and the dynamic structured mesh technique were used. SIMPLE algorithm and the k-ε turbulence model in the Descartes coordinates were also adopted. The hydrodynamics characteristics of different docking states were analyzed, such as the different docking velocity, the docking device including baffle or not. The drag coefficients of AUV in the process of docking were computed for various docking conditions, i.e., the AUV moving into the docking in the speed of 1m/s, 2m/s, 5m/s. The results indicate that the drag coefficient increases slowly in the process of AUV getting close to the docking device. When the AUV moves into the docking device, the drag coefficient increases rapidly. Then the drag coefficient decreases rapidly. The drag coefficient decreases with the increase of velocity when AUV enters the docking device. It was also found that the drag coefficient can be effectively reduced by dislodging the baffle of docking device.

Modeling of Compressor Drum Cavities With Radial Inflow

2016 ◽  
Author(s):  
D. Amirante ◽  
Z. Sun ◽  
J. W. Chew ◽  
N. J. Hills ◽  
N. R. Atkins
Keyword(s):  
Thermal Stratification ◽  
Turbulence Modeling ◽  
Navier Stokes ◽  
Inflow Rate ◽  
Cfd Models ◽  
Flow And Heat Transfer ◽  
Rotating Discs ◽  
Computational Fluid Dynamics Cfd ◽  
Inlet Conditions ◽  
Cooling Air

Reynolds-Averaged Navier-Stokes (RANS) computations have been conducted to investigate the flow and heat transfer between two co-rotating discs with an axial throughflow of cooling air and a radial bleed introduced from the shroud. The computational fluid dynamics (CFD) models have been coupled with a thermal model of the test rig, and the predicted metal temperature compared with the thermocouple data. CFD solutions are shown to vary from a buoyancy driven regime to a forced convection regime, depending on the radial inflow rate prescribed at the shroud. At a high radial inflow rate, the computations show an excellent agreement with the measured temperatures through a transient rig condition. At a low radial inflow rate, the cavity flow is destabilized by the thermal stratification. Good qualitative agreement with the measurements is shown, although a significant over-prediction of disc temperatures is observed. This is associated with under prediction of the penetration of the axial throughflow into the cavity. The mismatch could be the result of strong sensitivity to the prescribed inlet conditions, in addition to possible shortcomings in the turbulence modeling.

URANS Studies of Effect of Eccentricity on Ship–Lock Interactions

2016 ◽  
Vol 13 (04) ◽  
pp. 1641012
Author(s):  
Qingjie Meng ◽  
Decheng Wan
Keyword(s):  
Viscous Flow ◽  
Hydrodynamic Interaction ◽  
Vertical Displacement ◽  
Navier Stokes ◽  
Test Case ◽  
The Third ◽  
Surface Pressure Distribution ◽  
Sst Turbulence Model ◽  
Unsteady Viscous Flow ◽  
Ship Lock

The unsteady viscous flow around a 12000TEU ship model entering the Third Set of Panama Locks with different eccentricity is simulated by solving the unsteady Reynolds averaged Navier–Stokes (RANS) equations in combination with the [Formula: see text]SST turbulence model. Overset grid technology is utilized to maintain grid orthogonality and the effects of the free surface are taken into account. The hydrodynamic forces, vertical displacement as well as surface pressure distribution are predicted and analyzed. First, a benchmark test case is designed to validate the capability of the present methods in the prediction of the viscous flow around the ship when maneuvering into the lock. The accumulation of water in front of the ship during entry into a lock is noticed. A set of systematic computations with different eccentricity are then carried out to examine the effect of eccentricity on the ship–lock hydrodynamic interaction.

Mechanism and Flow Control on the Mismatching of Impeller and Vaned Diffuser Caused by Inlet Prewhirl for Centrifugal Compressors

2016 ◽  
Author(s):  
Qiangqiang Huang ◽  
Xinqian Zheng ◽  
Aolin Wang
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vaned Diffuser ◽  
Inlet Distortion ◽  
Computational Fluid Dynamics Cfd ◽  
Stagger Angle ◽  
Good Agreement ◽  
Matching Relation

Air often flows into compressors with inlet prewhirl, because it will obtain a circumferential component of velocity via inlet distortion or swirl generators such as inlet guide vanes. A lot of research has shown that inlet prewhirl does influence the characteristics of components, but the change of the matching relation between the components caused by inlet prewhirl is still unclear. This paper investigates the influence of inlet prewhirl on the matching of the impeller and the diffuser and proposes a flow control method to cure mismatching. The approach combines steady three-dimensional Reynolds-averaged Navier-Stokes (RANS) simulations with theoretical analysis and modeling. The result shows that a compressor whose impeller and diffuser match well at zero prewhirl will go to mismatching at non-zero prewhirl. The diffuser throat gets too large to match the impeller at positive prewhirl and gets too small for matching at negative prewhirl. The choking mass flow of the impeller is more sensitive to inlet prewhirl than that of the diffuser, which is the main reason for the mismatching. To cure the mismatching via adjusting the diffuser vanes stagger angle, a one-dimensional method based on incidence matching has been proposed to yield a control schedule for adjusting the diffuser. The optimal stagger angle predicted by analytical method has good agreement with that predicted by computational fluid dynamics (CFD). The compressor is able to operate efficiently in a much broader flow range with the control schedule. The flow range, where the efficiency is above 80%, of the datum compressor and the compressor only employing inlet prewhirl and no control are just 25.3% and 31.8%, respectively. For the compressor following the control schedule, the flow range is improved up to 46.5%. This paper also provides the perspective of components matching to think about inlet distortion.

The Effects of a Hydrostatic Pocket Aspect Ratio, Supply Orifice Position, and Attack Angle on Steady-State Flow Patterns, Pressure, and Shear Characteristics

1993 ◽  
Vol 115 (4) ◽  
pp. 678-685 ◽  
Author(s):  
M. J. Braun ◽  
F. K. Choy ◽  
Y. M. Zhou
Keyword(s):  
Stokes Equations ◽  
Staggered Grid ◽  
Navier Stokes ◽  
Computational Error ◽  
Convergence Criteria ◽  
Steady State Flow ◽  
Shear Forces ◽  
Navier Stokes Equations ◽  
Recirculating Flow ◽  
Shear Characteristics

The flow in a hydrostatic pocket is described by a mathematical model that uses the Navier-Stokes equations written in terms of the primary variables, u, v, and p. Using the conservative formulation, a finite difference method is applied through a staggered grid. The power law scheme is applied in the treatment of the convective terms for this highly recirculating flow. The discussion pertaining to the convergence of the numerical scheme and the computational error, shows that the strict convergence criteria applied to both velocities and pressure were successfully statisfied. The numerical model is applied in a parametric mode to the study of the velocities, the pressure patterns, and shear forces that characterize the flow in a square (α = 1), deep (α>1), and shallow (α≪1) hydrostatic pocket. The effects of the variation of the location and angle of the hydrostatic jet are also investigated.

The Effect of Turbulence and Real Gas Models on the Two Phase Spontaneously Condensing Flows in Nozzle

2013 ◽  
Author(s):  
Yogini Patel ◽  
Giteshkumar Patel ◽  
Teemu Turunen-Saaresti
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Nucleation Theory ◽  
Classical Nucleation Theory ◽  
Navier Stokes ◽  
Two Phase ◽  
Real Gas ◽  
Spontaneous Condensation ◽  
Condensing Flows ◽  
Computational Fluid Dynamics Cfd

The aim of the paper is to analyse the effect of turbulence and real gas models on the process of spontaneous condensation in converging diverging (CD) nozzle by using commercial Computational Fluid Dynamics (CFD) code. The calculations were based on the 2-D compressible Navier-Stokes (NS) equations coupled with two-equation turbulence model, and the non-equilibrium spontaneous condensing steam flow was solved on the basis of the classical nucleation theory. The results were validated to the available experimental data.

scholarly journals Three-Dimensional Navier–Stokes Analysis and Redesign of an Imbedded Bellmouth Nozzle in a Turbine Cascade Inlet Section

1996 ◽  
Vol 118 (3) ◽  
pp. 529-535 ◽  
Author(s):  
P. W. Giel ◽  
J. R. Sirbaugh ◽  
I. Lopez ◽  
G. J. Van Fossen
Keyword(s):  
Three Dimensional ◽  
Navier Stokes ◽  
Experimental Measurements ◽  
Inlet Section ◽  
Turbine Cascade ◽  
Blade Cascade ◽  
Inlet Geometry ◽  
Computational Fluid Dynamics Cfd ◽  
Transonic Turbine ◽  
Flow Nonuniformity

Experimental measurements in the inlet of a transonic turbine blade cascade showed unacceptable pitchwise flow nonuniformity. A three-dimensional, Navier–Stokes computational fluid dynamics (CFD) analysis of the imbedded bellmouth inlet in the facility was performed to identify and eliminate the source of the flow nonuniformity. The blockage and acceleration effects of the blades were accounted for by specifying a periodic static pressure exit condition interpolated from a separate three-dimensional Navier–Stokes CFD solution of flow around a single blade in an infinite cascade. Calculations of the original inlet geometry showed total pressure loss regions consistent in strength and location to experimental measurements. The results indicate that the distortions were caused by a pair of streamwise vortices that originated as a result of the interaction of the flow with the imbedded bellmouth. Computations were performed for an inlet geometry that eliminated the imbedded bellmouth by bridging the region between it and the upstream wall. This analysis indicated that eliminating the imbedded bellmouth nozzle also eliminates the pair of vortices, resulting in a flow with much greater pitchwise uniformity. Measurements taken with an installed redesigned inlet verify that the flow nonuniformity has indeed been eliminated.

Sign in / Sign up

Export Citation Format

Share Document