scholarly journals Efficient Removal of Levofloxacin by Activated Persulfate with Magnetic CuFe2O4/MMT-k10 Nanocomposite: Characterization, Response Surface Methodology, and Degradation Mechanism

Water ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 3583
Author(s):  
Junying Yang ◽  
Minye Huang ◽  
Shengsen Wang ◽  
Xiaoyun Mao ◽  
Yueming Hu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Photoelectron Spectroscopy ◽  
Degradation Mechanism ◽  
Sol Gel ◽  
Combustion Method ◽  
Copper Ferrite ◽  
X Ray ◽  
Rsm Model

In this study, a magnetic copper ferrite/montmorillonite-k10 nanocomposite (CuFe2O4/MMT-k10) was successfully fabricated by a simple sol-gel combustion method and was characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), the Brunner–Emmett–Teller (BET) method, vibrating sample magnetometer (VSM), and X-ray photoelectron spectroscopy (XPS). For levofloxacin (LVF) degradation, CuFe2O4/MMT-k10 was utilized to activate persulfate (PS). Due to the relative high adsorption capacity of CuFe2O4/MMT-k10, the adsorption feature was considered an enhancement of LVF degradation. In addition, the response surface methodology (RSM) model was established with the parameters of pH, temperature, PS dosage, and CuFe2O4/MMT-k10 dosage as the independent variables to obtain the optimal response for LVF degradation. In cycle experiments, we identified the good stability and reusability of CuFe2O4/MMT-k10. We proposed a potential mechanism of CuFe2O4/MMT-k10 activating PS through free radical quenching tests and XPS analysis. These results reveal that CuFe2O4/MMT-k10 nanocomposite could activate the persulfate, which is an efficient technique for LVF degradation in water.

scholarly journals Enhanced Photocatalytic Activity of CuWO4 Doped TiO2 Photocatalyst Towards Carbamazepine Removal under UV Irradiation

Separations ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 25
Author(s):  
Chukwuka Bethel Anucha ◽  
Ilknur Altin ◽  
Emin Bacaksız ◽  
Tayfur Kucukomeroglu ◽  
Masho Hilawie Belay ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Component Part ◽  
Energy Yield ◽  
Mechanical Agitation ◽  
X Ray

Abatement of contaminants of emerging concerns (CECs) in water sources has been widely studied employing TiO2 based heterogeneous photocatalysis. However, low quantum energy yield among other limitations of titania has led to its modification with other semiconductor materials for improved photocatalytic activity. In this work, a 0.05 wt.% CuWO4 over TiO2 was prepared as a powder composite. Each component part synthesized via the sol-gel method for TiO2, and CuWO4 by co-precipitation assisted hydrothermal method from precursor salts, underwent gentle mechanical agitation. Homogenization of the nanopowder precursors was performed by zirconia ball milling for 2 h. The final material was obtained after annealing at 500 °C for 3.5 h. Structural and morphological characterization of the synthesized material has been achieved employing X-ray diffraction (XRD), Fourier transform infra-red (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) N2 adsorption–desorption analysis, Scanning electron microscopy-coupled Energy dispersive X-ray spectroscopy (SEM-EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) for optical characterization. The 0.05 wt.% CuWO4-TiO2 catalyst was investigated for its photocatalytic activity over carbamazepine (CBZ), achieving a degradation of almost 100% after 2 h irradiation. A comparison with pure TiO2 prepared under those same conditions was made. The effect of pH, chemical scavengers, H2O2 as well as contaminant ion effects (anions, cations), and humic acid (HA) was investigated, and their related influences on the photocatalyst efficiency towards CBZ degradation highlighted accordingly.

scholarly journals Y3+ substituted Sr-hexaferrites: sol-gel synthesis, structural, magnetic and electrical characterization

Cerâmica ◽  
2019 ◽  
Vol 65 (374) ◽  
pp. 274-281 ◽  
Author(s):  
S. S. Satpute ◽  
S. R. Wadgane ◽  
S. R. Kadam ◽  
D. R. Mane ◽  
R. H. Kadam
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Electrical Characterization ◽  
Combustion Method ◽  
Hexagonal Structure ◽  
Strontium Hexaferrite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Studies ◽  
Auto Combustion

Abstract Y3+ substituted strontium hexaferrites having chemical composition SrYxFe12-xO19 (x= 0.0, 0.5, 1.0, 1.5) were successfully synthesized by sol-gel auto-combustion method. The structural and morphological studies of prepared samples were investigated by using X-ray diffraction technique, energy dispersive X-ray spectroscopy, field emission scanning electron microscopy (FE-SEM) and high-resolution transmission electron microscopy. The X-ray diffraction pattern confirmed the single-phase hexagonal structure of yttrium substituted strontium ferrite and the lattice parameters a and c increased with the substitution of Y3+ ions. The crystallite size also varied with x content from 60 to 80 nm. The morphology was studied by FE-SEM, and the grain size of nanoparticles ranged from 44 to 130 nm. The magnetic properties were investigated by using vibrating sample magnetometer. The value of saturation magnetization decreased from 49.60 to 35.40 emu/g. The dielectric constant decreased non-linearly whereas the electrical dc resistivity increased with the yttrium concentration in strontium hexaferrite.

scholarly journals Facile Preparation of Rod-like MnO Nanomixtures via Hydrothermal Approach and Highly Efficient Removal of Methylene Blue for Wastewater Treatment

Nanomaterials ◽  
2018 ◽  
Vol 9 (1) ◽  
pp. 10 ◽  
Author(s):  
Yuelong Xu ◽  
Bin Ren ◽  
Ran Wang ◽  
Lihui Zhang ◽  
Tifeng Jiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Degradation Mechanism ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Transmission Electron ◽  
Degradation Ratio ◽  
Hydrothermal Approach

In the present study, nanoscale rod-shaped manganese oxide (MnO) mixtures were successfully prepared from graphitic carbon nitride (C3N4) and potassium permanganate (KMnO4) through a hydrothermal method. The as-prepared MnO nanomixtures exhibited high activity in the adsorption and degradation of methylene blue (MB). The as-synthesized products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), surface area analysis, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Furthermore, the effects of the dose of MnO nanomixtures, pH of the solution, initial concentration of MB, and the temperature of MB removal in dye adsorption and degradation experiments was investigated. The degradation mechanism of MB upon treatment with MnO nanomixtures and H2O2 was studied and discussed. The results showed that a maximum adsorption capacity of 154 mg g−1 was obtained for a 60 mg L−1 MB solution at pH 9.0 and 25 °C, and the highest MB degradation ratio reached 99.8% under the following optimum conditions: 50 mL of MB solution (20 mg L−1) at room temperature and pH ≈ 8.0 with 7 mg of C, N-doped MnO and 0.5 mL of H2O2.

Multiferroic Bismuth Ferrite Nanoparticles: Rapid Sintering Synthesis, Characterization, and Optical Properties

2010 ◽  
Vol 152-153 ◽  
pp. 81-85
Author(s):  
Xiong Wang ◽  
Yin Lin ◽  
Jin Guo Jiang
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
Optical Properties ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray ◽  
Bifeo3 Nanoparticles ◽  
Rapid Sintering

The homogeneous multiferroic BiFeO3 nanoparticles with average particle size of 85 nm have been successfully synthesized by a simple sol-gel route. The prepared sample was characterized by a variety of techniques, such as X-ray diffractometry, thermogravimetric analysis and differential thermal analysis, differential scanning calorimeter analysis, scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. The obtained results shows that rapid sintering and subsequently quenching to room temperature are the two vital important factors for the preparation of pure BiFeO3. The magnetic phase transition (TN = 369 °C) and the ferroelectric phase transition (TC = 824.5 °C) were determined, revealing the antiferromagnetic and ferroelectric nature of the as-prepared BiFeO3 nanoparticles. The optical properties of the nanopowders were investigated. The strong band-gap absorption at 486 nm (2.55 eV) of the BiFeO3 nanoparticles may bring some novel applications.

scholarly journals Lead-Free BNT–BT0.08/CoFe2O4 Core–Shell Nanostructures with Potential Multifunctional Applications

Nanomaterials ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 672
Author(s):  
Marin Cernea ◽  
Roxana Radu ◽  
Harvey Amorín ◽  
Simona Gabriela Greculeasa ◽  
Bogdan Stefan Vasile ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Molar Ratio ◽  
Transmission Electron Microscopy Data ◽  
Core Shell ◽  
Shell Nanoparticles ◽  
Two Phase ◽  
X Ray ◽  
Shell Nanostructures

Herein we report on novel multiferroic core–shell nanostructures of cobalt ferrite (CoFe2O4)–bismuth, sodium titanate doped with barium titanate (BNT–BT0.08), prepared by a two–step wet chemical procedure, using the sol–gel technique. The fraction of CoFe2O4 was varied from 1:0.5 to 1:1.5 = BNT–BT0.08/CoFe2O4 (molar ratio). X–ray diffraction confirmed the presence of both the spinel CoFe2O4 and the perovskite Bi0.5Na0.5TiO3 phases. Scanning electron microscopy analysis indicated that the diameter of the core–shell nanoparticles was between 15 and 40 nm. Transmission electron microscopy data showed two–phase composite nanostructures consisting of a BNT–BT0.08 core surrounded by a CoFe2O4 shell with an average thickness of 4–7 nm. Cole-Cole plots reveal the presence of grains and grain boundary effects in the BNT–BT0.08/CoFe2O4 composite. Moreover, the values of the dc conductivity were found to increase with the amount of CoFe2O4 semiconductive phase. Both X-ray photoelectron spectroscopy (XPS) and Mössbauer measurements have shown no change in the valence of the Fe3+, Co2+, Bi3+ and Ti4+ cations. This study provides a detailed insight into the magnetoelectric coupling of the multiferroic BNT–BT0.08/CoFe2O4 core–shell composite potentially suitable for magnetoelectric applications.

Spectroscopic and Morphological Investigation of Copper-Containing Nanocomposites

2015 ◽  
Vol 1091 ◽  
pp. 15-18 ◽  
Author(s):  
V.A. Shmatko ◽  
T.N. Myasoedova ◽  
G.E. Yalovega
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Grain Shape ◽  
Sol Gel ◽  
Oxide Phase ◽  
Morphological Investigation ◽  
X Ray ◽  
Gel Technique ◽  
Shape Changes ◽  
Scanning Electron

In the paper the SiO2CuOx and SiO2(CuOxSnOy) thin films were deposited from the alcoholic solutions employing the sol-gel technique. The films were characterized by means of SEM (scanning electron microscopy) and 2p x-ray photoelectron spectroscopy (XPS). The SEM studies found the grain shape changes from flower-like to regular shaped inorganic agglomerates as result of adding the SnCl4 into the sol. The X-ray photoelectron spectroscopy (XPS) studies showed the presence both CuO and CuO2 phases and formation of a double CuSiO3 oxide phase.

Characterization of Y/TiO2 Nanoparticles and their Reactivity for CO2 Photoreduction

2011 ◽  
Vol 55-57 ◽  
pp. 1506-1510 ◽  
Author(s):  
Jing Wei ◽  
Xin Tan ◽  
Tao Yu ◽  
Lin Zhao
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Chemical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Uv Illumination ◽  
Transmission Electron ◽  
And Chemical Properties

A series of Y/TiO2nanoparticles (NPs) were synthesized via sol-gel method. The crystal structures, morphologies and chemical properties were characterized using X-ray diffraction (XRD), high resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS). We investigated the effects of different doping amounts of Y on the reaction of CO2photoreduction. The results shown that 0.1 wt.%Y/TiO2(0.1YT) performed the highest photocatalytic activity, which yielded 384.62 µmol/g∙cat. formaldehyde after 6 h of UV illumination.

Synthesis of TiO2 and ZrO2 nanomaterials for the degradation of nerve agent simulants

2021 ◽  
Vol 11 (1) ◽  
pp. 105-110
Author(s):  
Dung Le Van ◽  
Phuong Dang Tuyet ◽  
Trinh Nguyen Duy ◽  
Manh Nguyen Ba
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Chemical Warfare Agent ◽  
Catalytic Performance ◽  
Sem Images ◽  
X Ray ◽  
Nitrophenyl Phosphate ◽  
Tio2 Nanomaterials ◽  
Adsorption Desorption

TiO2 and ZrO2 nanomaterials were successfully synthesized by sol gel method. Samples were characterized by X-ray difraction (XRD), Fourier-transform infrared spectroscopy (FTIR), N2 adsorption–desorption, Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS),  SEM images and TEM images of TiO2 and ZrO2 samples showed the particle size of 10–20 nm. The results have revealed highly porous structure of ZrO2 and TiO2 nanomaterials with specific surface area of 116 m2g-1 and 125 m2g-1, respectively. The TiO2 and ZrO2 materials were used as the degradation of dimethyl 4-nitrophenyl phosphate (DMNP) chemical warfare agent emulator. The ZrO2 nanomaterial exhibited highly catalytic performance of DMNP degradation and the conversion reached to the value of 90.64 %, after 120 min of reaction.

scholarly journals Physical Characteristics of Titania Nanofibers Synthesized by Sol-Gel and Electrospinning Techniques

2010 ◽  
Vol 5 (1) ◽  
pp. 155892501000500 ◽  
Author(s):  
Soo-Jin Park ◽  
Yong C. Kang ◽  
Ju Y. Park ◽  
Ed A. Evans ◽  
Rex D. Ramsier ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Average Diameter ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Ceramic Nanofibers ◽  
Titania Nanofibers

Titania nanofibers were successfully synthesized by sol-gel coating of electrospun polymer nanofibers followed by calcining to form either the pure anatase or rutile phases. Characterization of these materials was carried out using scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV-vis spectroscopy techniques. The average diameter of these ceramic nanofibers was observed to be around 200 nm for both the rutile and anatase forms. The valence band structure and optical absorption thresholds differ, however, indicating that nanofibrous mats of titania can be selectively developed for different applications in catalysis and photochemistry.

scholarly journals Evaluation for Simultaneous Removal of Anionic and Cationic Dyes onto Maple Leaf-Derived Biochar Using Response Surface Methodology

2020 ◽  
Vol 10 (9) ◽  
pp. 2982 ◽  
Author(s):  
Yong-Keun Choi ◽  
Ranjit Gurav ◽  
Hyung Joo Kim ◽  
Yung-Hun Yang ◽  
Shashi Kant Bhatia
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Photoelectron Spectroscopy ◽  
Pyrolysis Temperature ◽  
Rapid Development ◽  
Maximum Adsorption Capacity ◽  
Aqueous Mixtures ◽  
X Ray ◽  
Anionic Dye ◽  
Adsorption Temperature

Rapid development in the printing and dying industry produces large amounts of wastewater, and its discharge in the environment causes pollution. Keeping in view the carcinogenic and mutagenic properties of various dyes, it is important to treat dyed wastewater. Maple leaf biochars were produced at different pyrolysis temperatures, i.e., 350 °C, 550 °C, and 750 °C, characterized for physicochemical properties and used for the removal of cationic (methylene blue (MB)) and anionic dye (congo red (CR)). Response surface methodology (RSM) using three variables, i.e., pH (4, 7, and 10), pyrolysis temperature (350 °C, 550 °C, and 750 °C), and adsorption temperature (20 °C, 30 °C, and 40 °C), was designed to find the optimum condition for dyes removal. X-ray diffraction (XRD) analysis showed an increase in CaCO3 crystallinity and a decrease in MgCO3 crystallinity with the increase of pyrolysis temperature. RSM design results showed that maple biochar showed maximum adsorption capacity for cationic dye at higher pH (9–10) and for anionic dye at pH 4-6, respectively. Under the selected condition of pH 7 and an adsorption temperature of 30 °C, biochar MB550 was able to remove MB and CR by 68% and 74%, respectively, from dye mixtures. Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses showed that MB550 was able to remove both dyes simultaneously from the aqueous mixtures.

Sign in / Sign up

Export Citation Format

Share Document