scholarly journals Application Design Aiming to Minimize Drivers’ Trip Duration through Intermediate Charging at Public Station Deployed in Smart Cities

2019 ◽  
Vol 10 (4) ◽  
pp. 67
Author(s):  
Ibrahim El-Fedany ◽  
Driss Kiouach ◽  
Rachid Alaoui
Keyword(s):  
Electric Vehicles ◽  
Smart Cities ◽  
Limited Range ◽  
Electric Transport ◽  
Charging Infrastructure ◽  
Vehicle To Grid ◽  
The Road ◽  
Smart Charging ◽  
Grid Applications ◽  
On The Road

Today, smart cities are turning to electric transport, carpooling and zero emission zones. The growing number of electric vehicles on the roads makes it increasingly necessary to have a public charging infrastructure. On the other hand, the main limitations of electric vehicles are the limited range of their batteries and their relatively long charging times. To avoid having problems to recharge, electric vehicle drivers must plan their journeys more thoroughly than others. At the goal of optimizing trip time, drivers need to automate their travel plans based on a smart charging solution, which will require the development of new Vehicle-to-Grid applications that will allow at the charging stations to dynamically interact with the vehicles. In this paper, we propose an architecture based on an algorithm allowing the management of charging plans for electric vehicles traveling on the road to their destination, in order to minimize the duration of the drivers’ journey including waiting and charging times. The decision taken by the algorithm based on the exploration of the data of each public supply station according to its location, number of vehicles in the queue, number of charging sockets, and rates of service.

scholarly journals System architecture to select the charging station by optimizing the travel time considering the destination of electric vehicle drivers in smart cities

2020 ◽  
Vol 9 (1) ◽  
pp. 273-283
Author(s):  
Ibrahim El-fedany ◽  
Driss Kiouach ◽  
Rachid Alaoui
Keyword(s):  
Electric Vehicle ◽  
Electric Vehicles ◽  
Smart Cities ◽  
Time Of Arrival ◽  
Advance Reservation ◽  
The Road ◽  
Charging Station ◽  
Charging Time ◽  
On The Road ◽  
Charging Stations

The main limitations of electric vehicles are the limited scope of the battery and their relatively long charging times. This may cause discomfort to drivers of electric vehicles due to a long waiting period at the service of the charging station, during their trips. In this paper, we suggest a model system based on argorithms, allowing the management of charging plans of electric vehicles to travel on the road to their destination in order to minimize the duration of the drivers' journey. The proposed system decision to select the charging station, during advance reservation of electric vehicles, take into account the time of arrival of electric vehicles at charging stations, the expected charging time at charging stations, the local status of the charging stations in real time, and the amount of energy sufficient for the electric vehicle to arrive at the selected charging station. Furthermore, the system periodically updates the electric vehicule reservations to adjust their recharge plans, when they reach their selected earlier station compared to other vehicules requesting new reservations, or they may not arrive as they were forecast, due to traffic jams on the road or certain reluctance on the part of the driver.

scholarly journals Design & Construction of Electro Magnetic Induction based Roads (EMIR)

2019 ◽  
Vol 8 (9) ◽  
pp. 1340-1344
Keyword(s):  
Electric Vehicles ◽  
Large Population ◽  
Secondary Coil ◽  
Battery Life ◽  
Charging Infrastructure ◽  
The Road ◽  
Dynamic Charging ◽  
On The Road ◽  
Electro Magnetic ◽  
The Cost

Middle-east and especially UAE promotes the use of Electric Vehicles to bring down the carbon emission. Cost of Electric Vehicles (EVs) can be brought down by reducing the cost of its battery. Dynamic charging allows smaller and lighter batteries to be used due to frequent charging, using the charging infrastructure embedded under the roads. Hence this reduces the battery cost and improves the battery life. Reduction in battery cost will bring down the cost of EVs and thus will encourage large population to move toward EVs. This paper presents the design & construction of a prototype EMIR to facilitate dynamic charging of EVs. Aim of this project is to construct 32 feet long and 3 feet wide prototype road with Induction charging facility. Four primary coils with the dimension 164cm x 31 cm with 3 turns and an inductance of 29.1µH are uniformly spaced on the road. Secondary coil of 40 cm x 31 cm with 6 turns with an inductance of 20 µH is attached onto the lower side of the chassis of the EV.

scholarly journals To Represent Electric Vehicles in Electricity Systems Modelling—Aggregated Vehicle Representation vs. Individual Driving Profiles

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 539
Author(s):  
Maria Taljegard ◽  
Lisa Göransson ◽  
Mikael Odenberger ◽  
Filip Johnsson
Keyword(s):  
Electric Vehicles ◽  
Investment Model ◽  
Research Issues ◽  
Charging Infrastructure ◽  
Vehicle To Grid ◽  
Long Term Storage ◽  
Electricity System ◽  
Home Location ◽  
The Individual ◽  
Storage Technologies

This study describes, applies, and compares three different approaches to integrate electric vehicles (EVs) in a cost-minimising electricity system investment model and a dispatch model. The approaches include both an aggregated vehicle representation and individual driving profiles of passenger EVs. The driving patterns of 426 randomly selected vehicles in Sweden were recorded between 30 and 73 days each and used as input to the electricity system model for the individual driving profiles. The main conclusion is that an aggregated vehicle representation gives similar results as when including individual driving profiles for most scenarios modelled. However, this study also concludes that it is important to represent the heterogeneity of individual driving profiles in electricity system optimisation models when: (i) charging infrastructure is limited to only the home location in regions with a high share of solar and wind power in the electricity system, and (ii) when addressing special research issues such as impact of vehicle-to-grid (V2G) on battery health status. An aggregated vehicle representation will, if the charging infrastructure is limited to only home location, over-estimate the V2G potential resulting in a higher share (up to 10 percentage points) of variable renewable electricity generation and an under-estimation of investments in both short- and long-term storage technologies.

scholarly journals Analysis of Battery Reduction for an Improved Opportunistic Wireless-Charged Electric Bus

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2866
Author(s):  
Andong Yin ◽  
Shenchun Wu ◽  
Weihan Li ◽  
Jinfang Hu
Keyword(s):  
Cost Saving ◽  
Electric Vehicles ◽  
Attractive Alternative ◽  
Wireless Charging ◽  
Charging Infrastructure ◽  
The Road ◽  
Charging System ◽  
Electric Bus ◽  
The Cost ◽  
Operation Cost

As an attractive alternative to the traditional plug-in charged electric vehicles (EVs), wireless-charged EVs have recently been in the spotlight. Opportunistically charged utilizing the wireless-charging infrastructure installed under the road at bus stops, an electric bus can have a smaller and lighter battery pack. In this paper, an improved opportunistic wireless-charging system (OWCS) for electric bus is introduced, which includes the opportunistic stationary wireless-charging system (OSWCS) and opportunistic hybrid wireless-charging system (OHWCS) consisting of stationary wireless-charging and dynamic wireless-charging. A general battery reduction model is established for the opportunistic wireless-charged electric bus (OWCEB). Two different battery-reduction models are built separately for OWCEB on account of the characteristics of OSWCS and OHWCS. Additionally, the cost saving models including the production cost saving, the operation cost saving and total cost saving are established. Then, the mathematical models are demonstrated with a numerical example intuitively. Furthermore, we analyze several parameters that influence the effectiveness of battery reduction due to the application of an opportunistic wireless-charging system on an electric bus. Finally, some points worth discussing in this work are performed.

A Laboratory Method to Comprehensively Evaluate Abrasion, Traction and Rolling Resistance of Tire Tread Compounds

2007 ◽  
Vol 80 (4) ◽  
pp. 580-607 ◽  
Author(s):  
M. Heinz ◽  
K. A. Grosch
Keyword(s):  
Friction Coefficient ◽  
Laboratory Test ◽  
Rolling Resistance ◽  
Limited Range ◽  
Slip Angle ◽  
Testing Conditions ◽  
Side Force ◽  
The Road ◽  
Wide Range ◽  
On The Road

Abstract A laboratory test method has been developed which allows the evaluation of diverse properties of tire tread compounds on the same sample. The laboratory test instrument consists of a rotating abrasive disk against which a rubber sample wheel runs under a given load, slip angle and speed. All three force components acting on the wheel during the tests are recorded. By changing the variable values over a wide range practically all severities encountered in tire wear are covered. The well-known fact that compound ratings depend on the road testing conditions is verified. Most compounds are only significantly distinguishable against a control over a limited range of testing conditions. Using a road test simulation computer program based on the laboratory data shows that not only ratings correspond to practical experience but also calculated absolute tire life times do. Tests on surfaces of different coarseness and sharpness indicate that sharp coarse surfaces give the best results with road tests, which of necessity are mostly carried out on public roads of differing constitution. The abrasive surface can be wetted with water at different temperatures and hence either the friction force at a locked wheel or the side force at a slipping wheel can be measured over a wide range of temperatures and speeds. At small slip angles the side force is dominated by dynamic cornering stiffness of the compound, at large slip angles by the friction coefficient. In this case, too, good correlations to road experience exist over a limited range of testing conditions. Low water temperatures and low slip speed settings in the laboratory produce side force ratings, which correlate closely with ABS braking on the road High and higher slip speeds give ratings in close agreement with locked wheel braking on the road. A heatable/coolable disk enables traction measurements on ice and newly abrasion measurements on surfaces at elevated surface temperature. Ice surface temperatures between −5 °C and −25 °C are possible. Friction measurements show that the difference in compound rating between summer and winter compounds is maintained over the whole temperature range. New investigations show not only a differentiation between different winter tire treads qualities but also an excellent correlation between tire and laboratory results. As a new topic side force measurements on dry surfaces highlight the correlation to dry handling of tires. The tire tread compound contributes to this performance through its shear stiffness and its friction coefficient. The shear stiffness contributes to the response of the tire in directional changes. The friction coefficient determines the maximum force, which can be transmitted. A simple operation possibility for evaluation of determined side forces is demonstrated. In addition to antecedent investigations the rolling resistance of the rubber wheel can be measured over a range of loads and speeds with the slip angle set at zero. Again for these new results good correlations are achieved with practical experience. In particular, the dependence of the rolling resistance on the velocity and loads are pointed out. Ultimately a good correlation between tire test and laboratory test results was demonstrated.

Sign in / Sign up

Export Citation Format

Share Document