An integrated toolchain for the design of aeroacoustic metamaterials: the AERIALIST H2020 project.

2021 ◽  
Vol 263 (4) ◽  
pp. 2699-2707
Author(s):  
Umberto Iemma
Keyword(s):  
Additive Manufacturing ◽  
Wind Tunnel ◽  
Proof Of Concept ◽  
Experimental Proof ◽  
Acoustic Metamaterial ◽  
Design And Manufacturing ◽  
Final Design ◽  
Application Potential ◽  
Manufacturing Technologies ◽  
Breakthrough Innovation

The project AERIALIST (AdvancEd aicRaft-noIse-AlLeviation devIceS using meTamaterials), funded within the Breakthrough Innovation topic of the H2020 program, has closed its activity on May 2020. The objective of the project was the disclosure of the potential of metamaterials in developing disruptive devices for the mitigation of aircraft noise, in order to contribute to the identification of the breakthrough technologies targeted at the achievement of the noise reduction targets foreseen by the ACARE Flightpath 2050. Although targeted to low TRL, AERIALIST has been focused on the development of an integrated toolchain capable to address the entire design loop, from the early conception to the numerical and experimental proof of concept, up to the final design and manufacturing. The toolchain was founded onto four pillars: i) the extension of the acoustic metamaterial theory to aeroacoustics; ii) the exploitation of the latest additive manufacturing technologies; iii) the wind-tunnel assessment of the selected concepts; iv) the identification of a development roadmap towards higher TRL. After three years of activity, the project has attained all its objectives. The present paper is a review of the main outcomes of the project, their application potential and relevance to the ACARE objectives.

scholarly journals 3D Digitization and Additive Manufacturing Technologies in Medicine

2018 ◽  
Vol 26 (42) ◽  
pp. 165-170
Author(s):  
Ivan Molnár ◽  
Ladislav Morovič
Keyword(s):  
Additive Manufacturing ◽  
Manufacturing Processes ◽  
Design And Manufacturing ◽  
Medical Aids ◽  
Manufacturing Methods ◽  
Manufacturing Technologies ◽  
Design And Manufacture ◽  
3D Digitization ◽  
The Given

Abstract The paper discusses the use of 3D digitization and additive manufacturing technologies in the field of medicine. In addition, applications of the use of 3D digitization and additive manufacturing methods are described, focusing on the design and manufacture of individual medical aids. Subsequently, the process of designing and manufacturing of orthopedic aids using these technologies is described and the advantages of introducing the given technologies into the design and manufacturing processes in the medicine sector are presented.

Rapid Investment Casting: Design and Manufacturing Technologies

2019 ◽  
Author(s):  
Christopher T. Richard ◽  
Tsz-Ho Kwok
Keyword(s):  
Additive Manufacturing ◽  
Fatigue Strength ◽  
3D Printing ◽  
Surface Finish ◽  
Investment Casting ◽  
Biomedical Engineering ◽  
Design And Manufacturing ◽  
Manufacturing Methods ◽  
Manufacturing Technologies ◽  
Casting Design

Abstract With the emergence of new metal AM (additive manufacturing) methods, rapid IC (investment casting), a variation of conventional investment casting has been a popular topic of research in the fields of: aerospace, dentistry and biomedical engineering. RIC (Rapid investment casting) takes advantage of the additive nature of 3D printing for pattern making which allows for more complex castings than traditional investment casting. RIC is a manufacturing process that combines the casting knowledge accumulated over five thousand years with relatively novel AM knowledge. The result is a process that can compete with newer metal AM methods with the added benefits of excellent surface finish, fatigue strength and the ability to create parts from almost any metal or metal alloy. This article will focus on research advancements in investment casting, AM and all the topics that are closely related to optimizing these two processes. Beyond that, aerospace, dentistry and biomedical engineering advancements using investment casting will be reviewed.

scholarly journals Optimization Methodology for Additive Manufacturing of Customized Parts by Fused Deposition Modeling (FDM). Application to a Shoe Heel

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2119 ◽  
Author(s):  
Amabel García-Dominguez ◽  
Juan Claver ◽  
Miguel A. Sebastián
Keyword(s):  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Parametric Design ◽  
General Structure ◽  
Visual Programming ◽  
Application Development ◽  
Fused Deposition ◽  
Final Design ◽  
Optimization Methodology ◽  
Manufacturing Technologies

Additive manufacturing technologies offer important new manufacturing possibilities, but its potential is so big that only with the support of other technologies can it really be exploited. In that sense, parametric design and design optimization tools appear as two appropriate complements for additive manufacturing. Synergies existing between these three technologies allow for integrated approaches to the design of customized and optimized products. While additive manufacturing makes it possible to materialize overly complex geometries, parametric design allows designs to be adapted to custom characteristics and optimization helps to choose the best solution according to the objectives. This work represents an application development of a previous work published in Polymers which exposed the general structure, operation and opportunities of a methodology that integrates these three technologies by using visual programming with Grasshopper. In this work, the different stages of the methodology and the way in which each one modifies the final design are exposed in detail, applying it to a case study: the design of a shoe heel for FDM—an interesting example both from the perspectives of ergonomic and mass customization. Programming, operation and results are exposed in detail showing the complexity, usefulness and potential of the methodology, with the aim of helping other researchers to develop proposals in this line.

scholarly journals A STRUCTURED APPROACH TO REDUCE DESIGN ITERATIONS IN ADDITIVE MANUFACTURING

2021 ◽  
Vol 1 ◽  
pp. 231-240
Author(s):  
Laura Wirths ◽  
Matthias Bleckmann ◽  
Kristin Paetzold
Keyword(s):  
Additive Manufacturing ◽  
Spare Parts ◽  
Design Guidelines ◽  
Final Part ◽  
Layer By Layer ◽  
Powder Bed ◽  
Batch Sizes ◽  
Manufacturing Technologies ◽  
Structured Approach ◽  
Design Freedom

AbstractAdditive Manufacturing technologies are based on a layer-by-layer build-up. This offers the possibility to design complex geometries or to integrate functionalities in the part. Nevertheless, limitations given by the manufacturing process apply to the geometric design freedom. These limitations are often unknown due to a lack of knowledge of the cause-effect relationships of the process. Currently, this leads to many iterations until the final part fulfils its functionality. Particularly for small batch sizes, producing the part at the first attempt is very important. In this study, a structured approach to reduce the design iterations is presented. Therefore, the cause-effect relationships are systematically established and analysed in detail. Based on this knowledge, design guidelines can be derived. These guidelines consider process limitations and help to reduce the iterations for the final part production. In order to illustrate the approach, the spare parts production via laser powder bed fusion is used as an example.

scholarly journals Adhesion Studies during Generative Hybridization of Textile-Reinforced Thermoplastic Composites via Additive Manufacturing

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3888
Author(s):  
Johanna Maier ◽  
Christian Vogel ◽  
Tobias Lebelt ◽  
Vinzenz Geske ◽  
Thomas Behnisch ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Polyamide 6 ◽  
Thermoplastic Composites ◽  
Efficient Production ◽  
Angle Measurements ◽  
Small Series ◽  
Contact Angle Measurements ◽  
Static Tensile ◽  
Pre Treatment ◽  
Manufacturing Technologies

Generative hybridization enables the efficient production of lightweight structures by combining classic manufacturing processes with additive manufacturing technologies. This type of functionalization process allows components with high geometric complexity and high mechanical properties to be produced efficiently in small series without the need for additional molds. In this study, hybrid specimens were generated by additively depositing PA6 (polyamide 6) via fused layer modeling (FLM) onto continuous woven fiber GF/PA6 (glass fiber/polyamide 6) flat preforms. Specifically, the effects of surface pre-treatment and process-induced surface interactions were investigated using optical microscopy for contact angle measurements as well as laser profilometry and thermal analytics. The bonding characteristic at the interface was evaluated via quasi-static tensile pull-off tests. Results indicate that both the bond strength and corresponding failure type vary with pre-treatment settings and process parameters during generative hybridization. It is shown that both the base substrate temperature and the FLM nozzle distance have a significant influence on the adhesive tensile strength. In particular, it can be seen that surface activation by plasma can significantly improve the specific adhesion in generative hybridization.

scholarly journals MODEL-BASED DESIGN OF AM COMPONENTS TO ENABLE DECENTRALIZED DIGITAL MANUFACTURING SYSTEMS

2021 ◽  
Vol 1 ◽  
pp. 2127-2136
Author(s):  
Olivia Borgue ◽  
John Stavridis ◽  
Tomas Vannucci ◽  
Panagiotis Stavropoulos ◽  
Harry Bikas ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Manufacturing Systems ◽  
Production Systems ◽  
Data Generation ◽  
Production Networks ◽  
Model Based ◽  
Manufacturing Technologies ◽  
Am Processes ◽  
Final Consumer

AbstractAdditive manufacturing (AM) is a versatile technology that could add flexibility in manufacturing processes, whether implemented alone or along other technologies. This technology enables on-demand production and decentralized production networks, as production facilities can be located around the world to manufacture products closer to the final consumer (decentralized manufacturing). However, the wide adoption of additive manufacturing technologies is hindered by the lack of experience on its implementation, the lack of repeatability among different manufacturers and a lack of integrated production systems. The later, hinders the traceability and quality assurance of printed components and limits the understanding and data generation of the AM processes and parameters. In this article, a design strategy is proposed to integrate the different phases of the development process into a model-based design platform for decentralized manufacturing. This platform is aimed at facilitating data traceability and product repeatability among different AM machines. The strategy is illustrated with a case study where a car steering knuckle is manufactured in three different facilities in Sweden and Italy.

scholarly journals Influence of Deposition Patterns on Distortion of H13 Steel by Wire-Arc Additive Manufacturing

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 485
Author(s):  
Xufeng Li ◽  
Jian Lin ◽  
Zhidong Xia ◽  
Yongqiang Zhang ◽  
Hanguang Fu
Keyword(s):  
Additive Manufacturing ◽  
Temperature History ◽  
H13 Steel ◽  
Deposition Patterns ◽  
Field Distortion ◽  
Set Up ◽  
Manufacturing Technologies ◽  
Inherent Strain ◽  
Inherent Strain Method ◽  
Wire Arc Additive Manufacturing

Wire-arc additive manufacturing (WAAM) has been considered as one of the potential additive-manufacturing technologies to fabricate large components. However, its industrial application is still limited by the existence of stress and distortion. During the process of WAAM, the scanning pattern has an important influence on the temperature field, distortion and final quality of the part. Four kinds of deposition patterns, including sequence, symmetry, in–out and out–in, were designed to deposit H13 steel in this study. An in situ measurement system was set up to record the temperature history and the progress of accumulated distortion of the parts during deposition. An S value was proposed to evaluate the distortion of the substrate. It was shown that the distortion of the part deposited by sequence was significantly larger than those of other parts. The distortion deposited by the out–in pattern decreased by 68.6% compared with sequence. The inherent strain method and strain parameter were introduced to expose the mechanism of distortion reduction caused by pattern variation.

scholarly journals Additive Manufacturing for Effective Smart Structures: The Idea of 6D Printing

2021 ◽  
Vol 5 (5) ◽  
pp. 119
Author(s):  
Stelios K. Georgantzinos ◽  
Georgios I. Giannopoulos ◽  
Panteleimon A. Bakalis
Keyword(s):  
Additive Manufacturing ◽  
Degrees Of Freedom ◽  
Smart Structures ◽  
Interaction Mechanism ◽  
Modeling And Simulations ◽  
Environmental Stimulus ◽  
Material Component ◽  
Design And Manufacturing ◽  
First Time ◽  
Printing Techniques

This paper aims to establish six-dimensional (6D) printing as a new branch of additive manufacturing investigating its benefits, advantages as well as possible limitations concerning the design and manufacturing of effective smart structures. The concept of 6D printing, to the authors’ best knowledge, is introduced for the first time. The new method combines the four-dimensional (4D) and five-dimensional (5D) printing techniques. This means that the printing process is going to use five degrees of freedom for creating the final object while the final produced material component will be a smart/intelligent one (i.e., will be capable of changing its shape or properties due to its interaction with an environmental stimulus). A 6D printed structure can be stronger and more effective than a corresponding 4D printed structure, can be manufactured using less material, can perform movements by being exposed to an external stimulus through an interaction mechanism, and it may learn how to reconfigure itself suitably, based on predictions via mathematical modeling and simulations.

Sign in / Sign up

Export Citation Format

Share Document