scholarly journals Petrological, Chemical, and Mineralogical Characterization of Anka (Zamfara State) Manganese Ore

NanoNEXT ◽  
2021 ◽  
pp. 7-12
Author(s):  
Gbadamosi Y.E ◽  
Alabi O.O ◽  
Ola-Omole O.O ◽  
Adetula Y.V
Keyword(s):  
Silicon Oxide ◽  
Raw Materials ◽  
Microscopy Study ◽  
Industrial Applications ◽  
Manganese Ore ◽  
X Ray Diffraction ◽  
Mineralogical Characterization ◽  
X Ray ◽  
Grinding Machine

Manganese deposit reserves exist in Nigeria, which have potentials as raw materials for industrial applications such as batteries, steel and electrical appliances. The present level of exploitation of Manganese is very low and, in most cases, appropriate processing would be necessary to attain desirable qualities. This paper provides petrological, chemical and mineralogical characterization of manganese ore in Anka area of Zamfara state, Nigeria. A chip of about 1/8 of an inch and about 1 inch by 1 inch was cut from the lumps of Anka (Zamfara state) manganese sample using rock cutter, after which their surfaces were trimmed and the chip was mounted on a grinding machine to make the surface smooth. The samples were mounted on a slide and viewed using Leica Petrological Microscope. 500 g of the ore was weighed using digital weighing balance. The sample was crushed and ground until 80% passing of 250µm is achieved. The ground ore was blended homogenously before the analysis while for the ore microscopy study, true fraction representative of the manganese ore samples were prepared, polished mounts and characterized using Scanning Electron Microscope-energy dispersed X-ray (SEM/EDX). However, X-ray Fluorescence was used to determine the chemical composition while identification of the associate mineral phase was done using X-ray Diffraction. From the petrological analysis carried out on the crude samples reveals the presence of heavy mineral and segregation distribution of the mineral. The XRF results shows 77.81% MnO, 60.26% Mn, 10.9% Fe2O3, 4% Al2O3 while Spessartine (3MnO.Al2O3, 0.830), Silicon oxide (SiO2, 1.122), Quartz (SiO4, 0.728), Pyrolusite (MnO, 1.543), and Almandine (Fe3Al2SiO12, 1.583) were identified as the major phases in the ore.

Metallographic Characterization of a Ti-Containing Low-Density Fe-Mn-Al-C Steel in As-Cast Condition

2016 ◽  
Vol 1812 ◽  
pp. 47-52
Author(s):  
Ignacio Mejía ◽  
Gladys Y. Díaz-Martínez ◽  
Arnoldo Bedolla-Jacuinde
Keyword(s):  
Raw Materials ◽  
Specific Weight ◽  
Industrial Applications ◽  
Low Density ◽  
X Ray Diffraction ◽  
Dendritic Microstructure ◽  
X Ray ◽  
Metallographic Technique ◽  
Cast Condition

ABSTRACTLow-density steels, with an excellent combination of outstanding mechanical properties, ultimate tensile strength and specific weight reduction, have been attracting great attention as a new group of materials in many industrial applications, particularly in the automotive industry. The aim of this work was to characterize the microstructure of a Ti-containing low-density Fe-Mn-Al-C steel in the as-cast condition. For this purpose, Ti-containing low-density steel was melted in an induction furnace using high purity raw materials and cast into a metal ingot mold. Chemical composition of the studied steel was Fe-32Mn-7.0Al-2.2C-0.5Ti (wt%). Samples were prepared by standard metallographic technique (grinding and polishing) and chemically etched with 2% nital solution, in order to reveal the dendritic microstructure. Microstructure observations were performed by scanning electron microscopy and the chemical nature of the present phases was determined by energy-dispersive X-ray. X-ray diffraction was performed at room temperature using a diffractometer with Cu Kα radiation. Phase equilibria by thermodynamic calculations for the studied steel were performed using JMatPro® software package. In general, results revealed a finer dendritic microstructure composed of ferritic matrix and austenite islands. The presence of ferrite and austenite in the steel was also confirmed by X-ray diffraction.

Clays from Southern Brazil: Physical, Chemical and Mineralogical Characterization

2005 ◽  
Vol 498-499 ◽  
pp. 447-452 ◽  
Author(s):  
Sivaldo Leite Correia ◽  
K.A.S. Curto ◽  
Dachamir Hotza ◽  
Ana M. Segadães
Keyword(s):  
Raw Materials ◽  
X Ray Diffraction ◽  
Rational Analysis ◽  
Porto Alegre ◽  
Mineralogical Characterization ◽  
X Ray ◽  
Muscovite Mica ◽  
Production Stages ◽  
Ceramics Industry

Fore knowledge of the characteristics of ceramic raw materials is of utmost importance during the development, processing and production stages of any ceramic product. This work describes the characterization of clays commonly used in the ceramics industry. Two different clays were selected: clay A, from Tubarão-SC and clay B, from Porto Alegre-RS. Their chemical composition was obtained by X-ray fluorescence and their mineralogy by X-ray diffraction, coupled with numerical rational analysis. Their thermal behaviour was studied by differential thermal analysis and thermogravimetry. Their particle size distribution and plasticity were also determined. Clay A showed circa 47.5 % quartz (by weight), 40.2 % kaolinite and 9.9 % muscovite mica. Clay B showed a high kaolinite content (circa 72 wt.%), accompanied by montmorillonite (circa 10 %) and potash feldspar (circa 10 % microcline). Clay B was found to be much more plastic than clay A, and both are suitable for pottery, tiles and brick making.

Characterization of Kaolin Residues from the Jarí Valley Reservations Provided by Cadam S/A Company

2018 ◽  
Vol 930 ◽  
pp. 14-19
Author(s):  
Alexsandra Cristina Chaves ◽  
I.V. da Silva ◽  
A.L. da Silva ◽  
G.A. Neves ◽  
Danielle Nascimento Silva Oliveira
Keyword(s):  
Environmental Issues ◽  
Industrial Applications ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Medium Size ◽  
X Ray Diffraction ◽  
Mineralogical Characterization ◽  
X Ray ◽  
A Company

The ceramic industry is one of the most important productive chains of the State of Pará, generating both money and employment. Kaolin has many industrial applications and new uses are constantly surveyed. Although the extraction and processing of kaolin contribute to the economy growth, the activity also provokes serious environmental issues. Being aware of the environmental problem caused by the inadequate decomposition of kaolin residues from the beneficiation process of these minerals, which pollute and attack the environment, this paper aims the chemical, physical and mineralogical characterization of the kaolin residue from the post-treatment disposal provided by CADAM S/A company. The main oxides in the residues were SiO2and Al2O3. In the X-ray diffraction analysis it was verified that the kaolin residue is basically formed by kaolinite and quartz, in the particle size analysis it was observed that the medium size of the particle was of 1,77 μm.

Bentonite Clays Characterization in the Town of Sossego – Paraiba State

2015 ◽  
Vol 820 ◽  
pp. 65-70
Author(s):  
I.D.S. Pereira ◽  
V.N.F. Lisboa ◽  
I.A. Silva ◽  
J.M.R. Figueirêdo ◽  
G.A. Neves ◽  
...  
Keyword(s):  
Industrial Applications ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Drilling Fluids ◽  
X Ray Diffraction ◽  
Mineralogical Characterization ◽  
Bentonite Clays ◽  
The Town ◽  
Petroleum Drilling

Bentonite exhibt a range of industrial applications moving millions of dollars on the market per year. Among several applications if highlights it is use for petroleum drilling fluids. Thus, this work aims to characterize physical, mineralogical and technologically, the bentonitics clays of Sossego County, Paraíba, Brazil. Mineralogical characterization of clays was done through the following techniques: particle size analysis by laser diffraction, thermogravimetric and differential thermal analysis, chemical analysis and x-ray diffraction. The clays were turned in by treatment with sodium in Na2CO3 and then determined whether the apparent viscosity, plastic and volume of filtrate of clay-water dispersions. The results showed that the samples are of polycationic, showing levels of MgO, CaO and K2O, similar to those from Boa Vista County, Paraíba, Brazil, and consist of clay mineral kaolinite, quartz and esmec. The clays showed rheological properties that indicate potential for use in drilling fluids.

Performance of Precursor Materials and Fired Ceramics for Structural Blocks

2015 ◽  
Vol 820 ◽  
pp. 13-17
Author(s):  
Neila Gondim Azeredo ◽  
Euzébio Barnabé Zanelato ◽  
Jonas Alexandre ◽  
Afonso Rangel Garcez de Azevedo ◽  
Gustavo de Castro Xavier ◽  
...  
Keyword(s):  
Building Construction ◽  
Structural Ceramic ◽  
X Ray Diffraction ◽  
Mineralogical Characterization ◽  
X Ray ◽  
Physical Chemical ◽  
Ceramic Blocks ◽  
Clay Body ◽  
Structural Blocks

The physical, chemical and mineralogical characterization of a precursor clay body before firing is of relevance for understanding the technological performance of the fired clay ceramic. In particular, structural clay ceramic blocks used in building construction need to attend standard properties specified by the norms. In the present work the precursor clay body, typically used to fabricate structural blocks in Campos dos Goytacazes, state of Rio de Janeiro, Brazil, was characterized in terms of particle size distribution, X-ray diffraction, chemical composition and Atterberg limits. In addition, the performance of structural ceramic blocks, fabricated from the extruded clay body and fired at 850oC, was evaluated. The results indicated that the ceramic mechanical strength complies with the Brazilian norm but the water absorption is higher than the maximum specified by the norm. The characteristic of the clay body contribute to justify the structural blocks performance.

scholarly journals Petrographic and Chemical–Mineralogical Characterization of Mortars from the Cistern at Amaiur Castle (Navarre, Spain)

Minerals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 311 ◽  
Author(s):  
Graciela Ponce-Antón ◽  
Maria Cruz Zuluaga ◽  
Luis Angel Ortega ◽  
Juantxo Agirre Mauleon
Keyword(s):  
Organic Additive ◽  
X Ray Diffraction ◽  
Mineralogical Characterization ◽  
X Ray ◽  
Rock Fragments ◽  
Application Techniques ◽  
Aggregate Nature ◽  
Specific Construction ◽  
Selection Of

Mortars from the cistern in Amaiur Castle (Navarre, Spain) were analysed to assess the mortar manufacturing process and application techniques. To this end, optical microscopy, scanning electron microscopy (SEM), thermogravimetric analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), Raman microspectroscopy, and Fourier transform infrared spectroscopy (FTIR) were performed. The study of both structural and plaster mortars from Amaiur Castle cistern show patterns/rules in the mortar manufacture according to the specific construction requirements. A multilayer application technique was used for the construction of the cistern tank. Deliberate selection of the aggregate nature and grading contributed to mortar impermeability. Ceramic and silico-aluminous rock fragments were used as aggregates in the cistern tank to confer hydraulicity to the mortars, instead of carbonated aggregates as used in the vault. Aluminosilicated phases present in the aggregates led to the formation of amesite, which is a magnesium aluminosilicate hydrate (M-A-S-H) phase conferring hydraulicity to the mortar. Two types of additives were identified in the outer pigmented layer of plaster. Beeswax was the identified organic additive used to improve the impermeability of mortar, while hematite was the identified inorganic additive giving rise to the reddish colour of the layer.

Chemical-physical and mineralogical characterization of ceramic raw materials from Moroccan northern regions: Intriguing resources for industrial applications

2019 ◽  
Vol 182 ◽  
pp. 105274 ◽  
Author(s):  
Manal Monsif ◽  
Abdelaziz Zerouale ◽  
Noureddine Idrissi Kandri ◽  
Mirto Mozzon ◽  
Paolo Sgarbossa ◽  
...  
Keyword(s):  
Raw Materials ◽  
Industrial Applications ◽  
Mineralogical Characterization ◽  
Northern Regions

Physico-Mineralogical Characterization: Bentonitic Clays Recently Found in Olivedos, Paraíba, Brazil

2015 ◽  
Vol 820 ◽  
pp. 56-59
Author(s):  
F.K.A. Sousa ◽  
I.A. Silva ◽  
W.S. Cavalcanti ◽  
Gelmires Araújo Neves ◽  
Heber Carlos Ferreira
Keyword(s):  
Cation Exchange Capacity ◽  
Petroleum Industry ◽  
Specific Area ◽  
Exchange Capacity ◽  
X Ray Diffraction ◽  
Mineralogical Characterization ◽  
X Ray ◽  
Petroleum Wells ◽  
The Town

Used in various branches of the industry, bentonitic clays are considered a valuable mineral, used specially in the petroleum industry for manufacturing of fluids used the drilling of petroleum wells in long depth. Recently, a deposit of this valuable mineral was discovered in the town of Olivedos-PB. There are data that prove that this is a very poor and underdeveloped town. So, this work aims at the physico-mineralogical characterization of clays recently discovered and, this way, verify if they present similar characteristics which allow them to replace the clays from Boa Vista-PB, and if they can be used by the industry, thus bringing social development for that town. The characterization was made by means of the analysis of chemical composition by X-ray fluorescence (EDX), thermogravimetric and thermal differential analyses (TG and DTA), X-ray diffraction (XRD), cation-exchange capacity (CEC) and specific area (SA). The results show that the clays recently discovered in Olivedos-PB are polycationic clays, presenting MgO, CaO and K2O content, and that they are constituted by smectitic clay mineral, by quartz and kaolinite.

Synthesis and Characterization of New Polyurethane Adhesives

2006 ◽  
Vol 514-516 ◽  
pp. 843-847 ◽  
Author(s):  
Cristina Borges Correia ◽  
João C. Bordado
Keyword(s):  
Raw Materials ◽  
Impact Resistance ◽  
Inert Atmosphere ◽  
Stray Field ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Polyurethane Adhesives ◽  
Dimer Acids

Polyurethane adhesives provide excellent flexibility, impact resistance and durability. Polyurethanes are formed through the reaction of an isocyanate component with polyether or polyester polyols or other active hydrogen compounds. This paper refers to polyurethane adhesives made from polyester polyols with long aliphatic chains (up to 36 carbon atoms) and MDI (diphenylmethane-4,4’-diisocyanate). The polyester polyols have been made from dimer acids obtained from renewable sources and short chain diols. The polyols that were used presented different degrees of unsaturation. The influence of the different raw materials in the adhesives performance is studied. The polyurethanes were produced by reaction between quasi-stoichiometric quantities of polyol and MDI, at several temperatures. The reaction was carried under inert atmosphere and at temperatures below 100°C. Performance of the adhesives was tested by carrying adhesion, hardness and water absorption tests. Characterization of both the polyester polyols and polyurethane adhesives was carried by Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC), Magnetic Nuclear Resonance (NMR), X-Ray Diffraction (WAXD), Scanning RMN Imaging of 1H of Stray- Field b (MRI) and Brookfield viscometry.

scholarly journals Mineralogical, Physicochemical and Morphological Characterization of Okpella Clay

Mining Revue ◽  
2021 ◽  
Vol 27 (4) ◽  
pp. 78-82
Author(s):  
Nurudeen Salahudeen ◽  
Aminat Oluwafisayo Abodunrin
Keyword(s):  
Ph Value ◽  
Chemical Characterization ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Local Clay ◽  
Mineralogical Characterization ◽  
X Ray ◽  
Edo State ◽  
Fluorescence Analyzer

Abstract Local clay mineral was mined from Okpella Town, Etsako Local Government Area of Edo State, Nigeria. Mineralogical characterization of the clay was carried out using X-ray diffraction analyzer. Chemical characterization of the clay was carried out using X-ray fluorescence analyzer and the pH analysis of the clay was carried out using pH meter. The mineralogical analysis revealed that the clay was majorly a dolomite mineral having 72% dolomite. The impurities present are 18% cristobalite, 4.1% garnet, 5% calcite and 1% quicklime. The pH analysis of the clay revealed that the clay was acidic having average pH value of 3.9. The pH determined for the 1:1, 1:2, 1:4, 1:8 and 1:10 samples were 3.61, 3.85, 3.85, 4.05 and 4.09, respectively.

Sign in / Sign up

Export Citation Format

Share Document