The Mechanical Properties of Organic Modified Epoxy Resin

2020 ◽  
Vol 43 (3) ◽  
pp. 10-14
Author(s):  
Georgel MIHU ◽  
Claudia Veronica UNGUREANU ◽  
Vasile BRIA ◽  
Marina BUNEA ◽  
Rodica CHIHAI PEȚU ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Epoxy Resins ◽  
Mechanical Tests ◽  
Organic Modification ◽  
Three Point Bending ◽  
Modified Epoxy

Epoxy resins have been presenting a lot of scientific and technical interests and organic modified epoxy resins have recently receiving a great deal of attention. For obtaining the composite materials with good mechanical proprieties, a large variety of organic modification agents were used. For this study gluten and gelatin had been used as modifying agents thinking that their dispersion inside the polymer could increase the polymer biocompatibility. Equal amounts of the proteins were milled together and the obtained compound was used to form 1 to 5% weight ratios organic agents modified epoxy materials. To highlight the effect of these proteins in epoxy matrix mechanical tests as three-point bending and compression were performed.

scholarly journals MECHANICAL CHARACTERISTICS FOR COMPOSITE MATERIALS USING COMMERCIAL EPOXY RESINS AND DIFFERENT FILLERS

2021 ◽  
Vol 56 (5) ◽  
pp. 179-185
Author(s):  
Omar A. Amin ◽  
S. A. Hassan ◽  
M. A. Sadek ◽  
M. A. Radwan ◽  
Hany A. Elazab
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Three Dimensional ◽  
Mechanical Tests ◽  
Diglycidyl Ether ◽  
Dimensional Structure ◽  
Polymeric Chain ◽  
Hydroxyl Groups ◽  
Different Types

Epoxy resins are thermoset polymers that consist of epoxide groups in their molecular structure. It shows many attractive characteristics like strong adhesion, excellent mechanical strength, low shrinkage, excellent insulator, excellent chemical stability for acidic and basic environments, and microbial resistance due to the presence of hydroxyl groups and ether bonds and its three-dimensional structure. Many of these characteristics can be modified by adding strong bindings in the polymeric chain to give more improved characteristics. This research aims to prepare a composite material using epoxy resin and different types of fillers to achieve resistance to high kinetic energy impact. Experimental work is focused on preparing cured epoxy resin samples by using diglycidyl ether of bisphenol A (DGEBA) resin with tertiary amine as a hardener. In order to obtain different samples with different properties, we add different types of fillers, then mechanical tests are used to measure the mechanical properties of the samples. The results have proved that fiberglass is the best filler added to epoxy resins to improve its mechanical properties.

scholarly journals Modified Epoxy Resin Synthesis from Phosphorus—Containing Polyol and Physical Changes Studies in the Synthesized Products

Polymers ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2116 ◽  
Author(s):  
Jeong Beom Jang ◽  
Tae Hee Kim ◽  
Taeyoon Kim ◽  
Hye Jin Kim ◽  
Bongkuk Seo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Mechanical And Thermal Properties ◽  
Release Rates ◽  
Molding Compounds ◽  
Reinforced Plastics ◽  
Phosphorus Containing ◽  
Physical Changes ◽  
Modified Epoxy

Epoxy resins are commonly used to manufacture the molding compounds, reinforced plastics, coatings, or adhesives required in various industries. However, the demand for new epoxy resins has increased to satisfy diverse industrial requirements such as enhanced mechanical properties, thermal stability, or electrical properties. Therefore, in this study, we synthesized new epoxy resin (PPME) by modifying phosphorous-containing polyol. The prepared resin was analyzed and added to epoxy compositions in various quantities. The compositions were cured at high temperatures to obtain plastics to further test the mechanical and thermal properties of the epoxy resin. The measured tensile and flexural strength of epoxy compositions were similar to the composition without synthesized epoxy resin. However, the heat release rates of the compositions exhibited tendencies of a decrease proportional to the amount of PPME.

scholarly journals Mechanical properties (Tensile, Hardness and Shock resistance) for the phenol formaldehyde resin with Epoxy resin

2019 ◽  
Vol 12 (2) ◽  
pp. 35-43
Author(s):  
Mustafa A. Rajab
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Shock Resistance

Phenolic formaldehyde (resole) resin was used at a different weight (10%, 20%, 30%, 40%), with epoxy resins at varying percentages (90%, 80%, 70%, 60%) at 20 C °. In order to study the mechanical properties (which including: Tensile strength, hardness and shock resistance), for the purpose of analysis and comparison with the mechanical properties of alloys, and the selected part for the purpose of replacing the alloy with the composite materials to reduce weight and improve mechanical properties. The results indicate improved properties with increased epoxy resins due to increased bonding between components.

scholarly journals High modulus polyimide particle-reinforcement of epoxy composites

2021 ◽  
Author(s):  
Johannes Essmeister ◽  
M. Josef Taublaender ◽  
Thomas Koch ◽  
D. Alonso Cerrón-Infantes ◽  
Miriam M. Unterlass ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Composite Materials ◽  
Epoxy Matrix ◽  
Epoxy Composites ◽  
High Modulus ◽  
Particle Reinforcement

A novel class of fully organic composite materials with well-balanced mechanical properties and improved thermal stability was developed by incorporating highly crystalline, hydrothermally synthesized polyimide microparticles into an epoxy matrix.

Thermal Stabilities and the Thermal Degradation Kinetics Study of the Flame Retardant Epoxy Resins

2014 ◽  
Vol 1053 ◽  
pp. 263-267 ◽  
Author(s):  
Xiu Juan Tian
Keyword(s):  
Thermal Stability ◽  
Thermal Degradation ◽  
Flame Retardant ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Degradation Kinetics ◽  
Thermal Degradation Kinetics ◽  
Thermal Stabilities ◽  
Degradation Kinetic ◽  
Modified Epoxy

Thermal stability and thermal degradation kinetics of epoxy resins with 2-(Diphenylphosphinyl)-1, 4-benzenediol were investegated by thermogravimetric analysis (TGA) at different heating rates of 5 K/min, 10 K/min, 20 K/min and 40 K/min. The thermal degradation kinetic mechanism and models of the modified epoxy resins were determined by Coast Redfern method.The results showed that epoxy resins modified with the flame retardant had more thermal stability than pure epoxy resin. The solid-state decomposition mechanism of epoxy resin and the modified epoxy resin corresponded to the controlled decelerating ځ˽̈́˰̵̳͂͆ͅ˼˰̴̱̾˰̸̵̈́˰̵̸̳̱̹̽̾̓̽˰̶̳̹̾̈́̿̾̓ͅ˰̶˸ځ˹˰̵̵͇͂˰̃˸́˽ځ˹2/3. The introduction of phosphorus-containing flame retardant reduced thermal degradation rate of epoxy resins in the primary stage, and promote the formation of carbon layer.

Mechanichal Properties of DGEBA/TEPA Modified Epoxy Resin

2014 ◽  
Vol 775-776 ◽  
pp. 588-592
Author(s):  
Camila Rodrigues Amaral ◽  
Ruben Jesus Sanchez Rodriguez ◽  
Magno Luiz Tavares Bessa ◽  
Verônica Scarpini Cândido ◽  
Sergio Neves Monteiro
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Epoxy Resin ◽  
Yield Stress ◽  
Diglycidyl Ether ◽  
Notch Toughness ◽  
Epoxy Network ◽  
Structural Network ◽  
Flexural Tests ◽  
Modified Epoxy

The correlation between the structural network of a diglycidyl ether of the bisphenol-A (DGEBA) epoxy resin, modified by two distinct aliphatic amines (tetraethylenepentamine TEPA and jeffamine D230), and its mechanical properties, was investigated as possible matrix for abrasive composites applications. Both flexural tests, to determine the yield stress and the elastic modulus, as well as impact tests to determine the notch toughness, were performed. The DGEBA/D230 presented the highest stiffness and toughness but lowest yield stress. This epoxy network also displayed a greater plastic deformation during fracture.

MECHANICAL PROPERTIES OF EPOXY RESIN BASED GRAPHENE NANO PARTICLES COMPOSITE

2020 ◽  
Vol 15 (4) ◽  
Author(s):  
Durgaprasad Kollipara ◽  
Prabhakar Gope VNB ◽  
Raja Loya
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Epoxy Composite ◽  
Hardness Test ◽  
Industrial Applications ◽  
Mechanical Tests ◽  
Nano Particles ◽  
Potential Candidate ◽  
Matrix Composites ◽  
Reinforcing Material

Composites have tremendous applicability due to their excellent capabilities. The performance of composites mainly depends on the reinforcing material applied. A Graphene nanoparticle (GNP) is successful as an efficient reinforcing material due to its versatile as well as superior properties. Even at very low content, graphene can dramatically improve the properties of polymer and metal matrix composites. In this paper the effects of GNP on composites based on epoxy resin were analyzed. Different contents of GNP (0 – 4.5 vol. %) were added to the epoxy resin. The GNP/epoxy composite was fabricated under room temperature. Mechanical tests result such as tensile, flexural and hardness test show enhancements of the mechanical properties of the GNP/epoxy composite. The experimental results clearly show an improvement in Young’s modulus, tensile strength, and hardness as compared to pure epoxy. The results of this research are strong evidence for GNP/epoxy composites being a potential candidate for use in a variety of industrial applications, especially for automobile parts, aircraft components, and electronic parts such as super capacitors, transistors, etc.

scholarly journals Properties of AlSi9Cu3 metal matrix micro and nano composites produced via stir casting

2018 ◽  
Vol 16 (1) ◽  
pp. 726-731 ◽  
Author(s):  
Tennur Gülşen Ünal ◽  
Ege Anıl Diler
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix ◽  
Weight Fraction ◽  
Stir Casting ◽  
Mechanical Tests ◽  
Matrix Composites ◽  
Casting Method ◽  
Porosity Formation ◽  
Three Point Bending ◽  
Hardness Values

AbstractThe effects of micro and nano sized reinforcement particles on microstructure and mechanical properties of aluminium alloy-based metal matrix composites were investigated in this study. AlSi9Cu3 alloy was reinforced with micro and nano sized ceramic reinforcement particles at different weight fractions by using a stir casting method. The mechanical tests (hardness, three point bending) were performed to determine the mechanical properties of AlSi9Cu3 alloy-based microcomposites (AMMCs) and nanocomposites (AMMNCs). The experimental results have shown that the size and weight fraction of reinforcement particles have a strong influence on the microstructure and the mechanical properties of AlSi9Cu3 alloy-based microcomposites and nanocomposites. The relative densities of all AMMC and AMMNC samples are lower than unreinforced AlSi9Cu3 alloy due to porosity formation with the increase of weight fraction of reinforcement particles. As weight fraction increases, hardness values of AMMCs and AMMNCs increase. Maximum flexural strength can be obtained at 3.5wt.% for the AMMC sample with microsized Al2O3 particles and at 2wt.% for the AMMNC sample with nano-sized Al2O3 particles. After the weight fractions exceed these values, flexural strengths of both AMMCs and AMMNCs decrease due to clustering of Al2O3 particles.

scholarly journals A bio-based phosphaphenanthrene-containing derivative modified epoxy thermosets with good flame retardancy, high mechanical properties and transparency

RSC Advances ◽  
2021 ◽  
Vol 11 (49) ◽  
pp. 30943-30954
Author(s):  
Wei Peng ◽  
Yu-xuan Xu ◽  
Shi-bin Nie ◽  
Wei Yang
Keyword(s):  
Mechanical Properties ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Epoxy Resins ◽  
Flame Retardants ◽  
The Past ◽  
Phosphorus Containing ◽  
Modified Epoxy

Phosphorus-containing flame retardants have received huge interest for improving the flame retardant behavior of epoxy resins (EP) over the past few decades.

Sign in / Sign up

Export Citation Format

Share Document