scholarly journals Thermal Performance of Thermosyphons Intended for Evacuated Tube Solar Collector Using Graphene Oxide Nanofluids

2021 ◽  
Vol 1 (1) ◽  
pp. 14-19
Author(s):  
T. Antonini Alves
Keyword(s):  
Graphene Oxide ◽  
Thermodynamic Cycle ◽  
Working Fluid ◽  
Outer Diameter ◽  
Joule Effect ◽  
Running Water ◽  
Glass Tubes ◽  
Evacuated Tube ◽  
Heat Loads ◽  
Adiabatic Section

Vacuum tube solar collectors are composed by two concentric glass tubes with the annular space evacuated. At the inner tube a thermosyphon is placed inside a metallic fin in order to absorb sun’s irradiation and heat running water placed at a manifold. Thermosyphons are passive heat transfer devices that absorb heat at the evaporator region, evaporating the working fluid that reaches the condenser in the form of steam. At the condenser, heat is dissipated to the environment, condensing the working fluid that returns to the evaporator, closing the thermodynamic cycle. In this study, thermosyphons with three different working fluids (5 and 10% graphene oxide nanofluids and distilled water) were built and experimentally tested. The evaporator and the adiabatic section have an outer diameter of 8.33mm and lengths of 1,600mm and 40mm, respectively. The condenser has an outer diameter of 13.40mm and a length of 35mm. The filling ratio used was 50% of the evaporator’s volume. A resistive tape wrapped at the evaporator and connected to a power supply was responsible for heating the working fluid by Joule effect, and water flow rates of 0.50, 0.75, and 1.00L/min were responsible for condensing the working fluid at the condenser. Heat loads of 35, 55, and 75W were applied to the devices and K-type thermocouples were responsible for acquiring temperature data from the thermosyphons, allowing the thermal analysis based in the temperature distribution and thermal resistance for each working fluid. The best working fluid for the conditions proposed, out of the three investigated, was 5% graphene oxide.

Development of a Copper Heat Pipe with Axial Grooves Manufactured Using Wire Electrical Discharge Machining (Wire-EDM)

2015 ◽  
Vol 1120-1121 ◽  
pp. 1325-1329 ◽  
Author(s):  
Felipe B. Nishida ◽  
Larissa S. Marquardt ◽  
Valquíria Y.S. Borges ◽  
Paulo H.D. Santos ◽  
Thiago Antonini Alves
Keyword(s):  
Heat Pipe ◽  
Thermal Management ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Average Diameter ◽  
Working Fluid ◽  
Outer Diameter ◽  
Wire Electrical Discharge Machining ◽  
Wire Edm ◽  
Heat Loads

In this research, a heat pipe with grooves was experimentally analyzed for the application in thermal management of electronic packaging. The heat pipe was produced by a copper tube with an outer diameter of 9.45 mm, length of 205 mm, and capillary structure composed by axial grooves with average diameter of 220 μm. The grooves were manufactured using wire electrical discharge machining (wire-EDM). The working fluid used was de-ionized water. The condenser was cooled by air forced convection and the evaporator was heated using an electrical resistor. This heat pipe was tested horizontally to increasing heat loads varying from 5 to 15 W. The experimental results showed that the heat pipe worked successfully.

scholarly journals EXPERIMENTAL ANALYSIS OF A SCREEN-COVERED GROOVE HEAT PIPE

2018 ◽  
Vol 17 (1) ◽  
pp. 58
Author(s):  
L. Krambeck ◽  
G. A. Bartmeyer ◽  
P. H. D. Santos ◽  
T. Antonini Alves
Keyword(s):  
Heat Pipe ◽  
Electrical Discharge Machining ◽  
Filling Ratio ◽  
Working Fluid ◽  
External Diameter ◽  
Wire Edm ◽  
Capillary Structure ◽  
Inner Diameter ◽  
Heat Loads ◽  
Adiabatic Section

In this research, a heat pipe with screen-covered groove capillary structure was experimentally analyzed. The heat pipe was manufactured from a copper tube with the external diameter of 9.45mm, inner diameter of      6.20mm, and a total length of 200mm. A Wire Electrical Discharge Machining, or Wire-EDM, was used to manufacture axial microgrooves in the heat pipe. A layer of phosphor bronze mesh #100 completed the capillary structure. Distilled water was the working fluid and the loading filling ratio was 60% of the evaporator volume. The condenser was cooled by air forced convection, the adiabatic section was insulated with fiberglass, and the evaporator was heated by an electrical resistor and it was insulated from the environment with aeronautic insulation. The heat pipe was tested in horizontal position, under different heat loads varying from 5 up to 30W. The experimental results showed that the screen-covered groove worked satisfactorily as a capillary structure.

scholarly journals Experimental Research on the Behaviour of Heat Pipe Using Graphene Oxide as Working Fluid

2019 ◽  
Vol 8 (2S11) ◽  
pp. 2052-2055
Keyword(s):  
Graphene Oxide ◽  
Heat Pipe ◽  
Electronic Devices ◽  
Vital Role ◽  
Working Fluid ◽  
Main Concern ◽  
Outer Diameter ◽  
Evaporation Zone ◽  
Innovative Techniques ◽  
Day By Day

The liberation of heat from the electronic devices used in the industries, refrigeration and etc. is main concern today. The temperature of the planet earth is being increasing day by day, the generation of heat by the manufacturing industries should be reduced using innovative techniques. Generally a heat exchangers were used to reduce it. In this study, graphene oxide employed as as working fluid to determine the effective thermal conductivity. The working fluid graphene oxide plays vital role in dissipation of heat from the evaporation zone to condensed zone. The experiment setup was done with about 19.1 mm and 21 mm inner and outer diameter, respectively. The length of the heat pipe is 600 mm. The wick material was made up of brass. We observed that the graphene oxide improved thew efficieny by using as working fluid.

scholarly journals Experimental research of capillary structure technologies for heat pipes

2020 ◽  
Vol 42 ◽  
pp. e48189
Author(s):  
Larissa Krambeck ◽  
Guilherme Antonio Bartmeyer ◽  
Davi Fusão ◽  
Paulo Henrique Dias dos Santos ◽  
Thiago Antonini Alves
Keyword(s):  
Heat Pipe ◽  
Thermal Management ◽  
Electrical Discharge Machining ◽  
Heat Pipes ◽  
Working Fluid ◽  
Outer Diameter ◽  
Wire Edm ◽  
Sintering Process ◽  
Capillary Structure ◽  
Heat Loads

This paper presents an experimental study on three different capillary structure technologies of heat pipes for application in the thermal management of electronic packaging. The first capillary structure is that of axial grooves manufactured by wire electrical discharge machining (wire-EDM). The sintering process with copper powder produced the second heat pipe. Finally, a hybrid heat pipe was made by the combination of the two previous methods. The heat pipes were produced using copper tubes with an outer diameter of 9.45 mm and a length of 200 mm, and were tested horizontally at increasing heat loads varying from 5 to 35 W. The working fluid used was distilled water. The experimental results showed that all capillary structures for heat pipes worked successfully, so the studied manufacturing methods are suitable. Nonetheless, the hybrid heat pipe is the best, due to the lowest thermal resistance presented.

Model, simulation and experiments for a Buoyancy Organic Rankine Cycle

2020 ◽  
Vol 92 (1) ◽  
pp. 10906
Author(s):  
Jeroen Schoenmaker ◽  
Pâmella Gonçalves Martins ◽  
Guilherme Corsi Miranda da Silva ◽  
Julio Carlos Teixeira
Keyword(s):  
Model Simulation ◽  
Organic Rankine Cycle ◽  
Thermodynamic Cycle ◽  
Rankine Cycle ◽  
Test Body ◽  
Working Fluid ◽  
Proof Of Concept ◽  
Energy Scenario ◽  
New Type ◽  
Fluid Reservoir

Organic Rankine Cycle (ORC) systems are increasingly gaining relevance in the renewable and sustainable energy scenario. Recently our research group published a manuscript identifying a new type of thermodynamic cycle entitled Buoyancy Organic Rankine Cycle (BORC) [J. Schoenmaker, J.F.Q. Rey, K.R. Pirota, Renew. Energy 36, 999 (2011)]. In this work we present two main contributions. First, we propose a refined thermodynamic model for BORC systems accounting for the specific heat of the working fluid. Considering the refined model, the efficiencies for Pentane and Dichloromethane at temperatures up to 100 °C were estimated to be 17.2%. Second, we show a proof of concept BORC system using a 3 m tall, 0.062 m diameter polycarbonate tube as a column-fluid reservoir. We used water as a column fluid. The thermal stability and uniformity throughout the tube has been carefully simulated and verified experimentally. After the thermal parameters of the water column have been fully characterized, we developed a test body to allow an adequate assessment of the BORC-system's efficiency. We obtained 0.84% efficiency for 43.8 °C working temperature. This corresponds to 35% of the Carnot efficiency calculated for the same temperature difference. Limitations of the model and the apparatus are put into perspective, pointing directions for further developments of BORC systems.

Optimization of a Novel Combined Power/Refrigeration Thermodynamic Cycle

Solar Energy ◽  
2002 ◽  
Author(s):  
Shaoguang Lu ◽  
D. Yogi Goswami
Keyword(s):  
Waste Heat ◽  
Thermodynamic Cycle ◽  
Cycle Performance ◽  
Working Fluid ◽  
Second Law ◽  
Optimum Conditions ◽  
Ambient Temperatures ◽  
Reduced Gradient ◽  
Generalized Reduced Gradient ◽  
Performance Conditions

A novel combined power/refrigeration thermodynamic cycle is optimized for thermal performance in this paper. The cycle uses ammonia-water binary mixture as a working fluid and can be driven by various heat sources, such as solar, geothermal and low temperature waste heat. It could produce power as well as refrigeration with power output as a primary goal. The optimization program, which is based on the Generalized Reduced Gradient (GRG) algorithm, can be used to optimize for different objective functions. Examples that maximize second law efficiency, work output and refrigeration output are presented, showing the cycle may be optimized for any desired performance parameter. In addition, cycle performance over a range of ambient temperatures was investigated. It was found that for a source temperature of 360K, which is in the range of flat plate solar collectors, both power and refrigeration outputs are achieved under optimum conditions. All performance parameters, including first and second law efficiencies, power and refrigeration output decrease as the ambient temperature goes up. On the other hand, for a source of 440K, optimum conditions do not provide any refrigeration. However, refrigeration can be obtained even for this temperature under non-optimum performance conditions.

Novel Combined Power and Cooling Thermodynamic Cycle for Low Temperature Heat Sources, Part II: Experimental Investigation

2003 ◽  
Vol 125 (2) ◽  
pp. 223-229 ◽  
Author(s):  
Gunnar Tamm ◽  
D. Yogi Goswami
Keyword(s):  
Low Temperature ◽  
System Analysis ◽  
Waste Heat ◽  
Thermal Power ◽  
Experimental System ◽  
Thermodynamic Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Water Mixture ◽  
Theoretical Simulation

A combined thermal power and cooling cycle proposed by Goswami is under intensive investigation, both theoretically and experimentally. The proposed cycle combines the Rankine and absorption refrigeration cycles, producing refrigeration while power is the primary goal. A binary ammonia-water mixture is used as the working fluid. This cycle can be used as a bottoming cycle using waste heat from a conventional power cycle or as an independent cycle using low temperature sources such as geothermal and solar energy. An experimental system was constructed to demonstrate the feasibility of the cycle and to compare the experimental results with the theoretical simulation. Results showed that the vapor generation and absorption condensation processes work experimentally, exhibiting expected trends, but with deviations from ideal and equilibrium modeling. The potential for combined turbine work and refrigeration output was evidenced in operating the system. Analysis of losses showed where improvements could be made, in preparation for further testing over a broader range of operating conditions.

Thermal Performance of Water-Based Suspensions of Phase Change Nanocapsules in a Natural Circulation Loop

2013 ◽  
Author(s):  
C. J. Ho ◽  
Chi-Ming Lai
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Natural Circulation ◽  
Pure Water ◽  
Circulation Loop ◽  
Core Material ◽  
Working Fluid ◽  
Outer Diameter ◽  
Natural Circulation Loop ◽  
Water Based

Experiments were conducted to investigate the heat transfer characteristics of water-based suspensions of phase change nanocapsules in a natural circulation loop with mini-channel heat sinks and heat sources. A total of 23 and 34 rectangular mini-channels, each with width 0.8 mm, depth 1.2 mm, length 50 mm and hydraulic diameter 0.96 mm, were evenly placed on the copper blocks as the heat source and heat sink, respectively. The adiabatic sections of the circulation loop were constructed using PMMA tubes with an outer diameter of 6 mm and an inner diameter of 4 mm, which were fabricated and assembled to construct a rectangular loop with a height of 630 mm and a width of 220 mm. Using a core material of n-eicosane and a shell of urea-formaldehyde resin, the phase change material nanocapsules of mean particle size 150 nm were fabricated successfully and then dispersed in pure water as the working fluid to form the water-based suspensions with mass fractions of the nanocapsules in the range 0.1–1 wt.%. The results clearly indicate that water-based suspensions of phase change nanocapsules can markedly enhance the heat transfer performance of the natural circulation loop considered.

Multi-Objective Optimization of a Combined Power and Cooling Cycle for Low-Grade and Midgrade Heat Sources

2012 ◽  
Vol 134 (3) ◽  
Author(s):  
Gokmen Demirkaya ◽  
Saeb Besarati ◽  
Ricardo Vasquez Padilla ◽  
Antonio Ramos Archibold ◽  
D. Yogi Goswami ◽  
...  
Keyword(s):  
Thermodynamic Cycle ◽  
Solution Concentration ◽  
Working Fluid ◽  
Low Grade ◽  
Basic Solution ◽  
Heat Sources ◽  
Fluid Mixture ◽  
Cooling Cycle ◽  
Multi Objective ◽  
First Case

Optimization of thermodynamic cycles is important for the efficient utilization of energy sources; indeed, it is more crucial for the cycles utilizing low-grade heat sources where the cycle efficiencies are smaller compared to high temperature power cycles. This paper presents the optimization of a combined power/cooling cycle, also known as the Goswami cycle, which combines the Rankine and absorption refrigeration cycles. The cycle uses a special binary fluid mixture as the working fluid and produces a power and refrigeration. In this regard, multi-objective genetic algorithms (GAs) are used for Pareto approach optimization of the thermodynamic cycle. The optimization study includes two cases. In the first case, the performance of the cycle is evaluated as it is used as a bottoming cycle and in the second case, as it is used as a top cycle utilizing solar energy or geothermal sources. The important thermodynamic objectives that have been considered in this work are, namely, work output, cooling capacity, effective first law, and exergy efficiencies. Optimization is carried out by varying the selected design variables, such as boiler temperature and pressure, rectifier temperature, and basic solution concentration. The boiler temperature is varied between 70–150 °C and 150–250 °C for the first and the second cases, respectively.

Investigation of Loop Heat Pipe Startup Using Liquid Core Visualization

2008 ◽  
Author(s):  
B. P. d’Entremont ◽  
J. M. Ochterbeck
Keyword(s):  
Heat Pipe ◽  
Liquid Core ◽  
High Heat ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Two Phase ◽  
Buoyancy Driven Flows ◽  
Compensation Chamber ◽  
Fill Level ◽  
Heat Loads

In this investigation, a Loop Heat Pipe (LHP) evaporator has been studied using a borescope inserted through the compensation chamber into the liquid core. This minimally intrusive technique allows liquid/vapor interactions to be observed throughout the liquid core and compensation chamber. A low conductivity ceramic was used for the wick and ammonia as the working fluid. Results indicate that buoyancy driven flows, both two-phase and single-phase, play essential roles in evacuating excess heat from the core, which explains the several differences in performance between horizontal and vertical orientations of the evaporator. This study also found no discernable effect of the pre-start fill level of the compensation chamber on thermal performance during startup at moderate and high heat loads.

Sign in / Sign up

Export Citation Format

Share Document