scholarly journals Manufacturing and Properties of Al-Al2O3 Composite Coating Layer Using Warm Spray Process

2017 ◽  
Vol 27 (7) ◽  
pp. 372-378
Author(s):  
의표 권 ◽  
◽  
종권 이
Keyword(s):  
Composite Coating ◽  
Coating Layer ◽  
Warm Spray ◽  
Spray Process ◽  
Al2o3 Composite

scholarly journals Influence of nano-SiO2 on the bonding strength and wear resistance properties of polyurethane coating

2019 ◽  
Vol 26 (1) ◽  
pp. 77-83 ◽  
Author(s):  
Fangfang Wang ◽  
Lajun Feng ◽  
Huini Ma ◽  
Zhe Zhai ◽  
Zheng Liu
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Composite Coating ◽  
Network Structure ◽  
Bonding Strength ◽  
Coating Layer ◽  
Steel Substrate ◽  
Polyurethane Coating ◽  
Nano Sio2

Abstract To improve the wear resistance of polyurethane (PU) coating and its adhesion to the steel substrate, a series of simple and practicable techniques were designed to mix nano-SiO2 with PU powder to cast a coating layer onto the steel. When the addition of nano-SiO2 was small, a network structure of PU-SiO2 was produced. It improved the wear resistance of the composite coating and its adhesion to the steel substrate. When the addition of nano-SiO2 was excessive, agglomerated nano-SiO2 particles not only affected the bond between the PU resin and the steel substrate but also became abrasive materials, intensifying the abrasion of the composite coating during friction. It resulted in lower bonding strength and poorer wear resistance of the composite coating. The wear rate and friction coefficient of 2 wt.% SiO2/PU composite coating were 1.52×10−6 cm3/min N and 0.31, respectively. Its wear resistance was about 10 times as high as that of the pure PU coating. Furthermore, a simple and practicable installation was designed to test the bonding strength between the coating and the steel substrate. The bonding strength between 2 wt.% SiO2/PU composite coating and the steel substrate was 7.33 MPa, which was 39% higher than that of the pure PU coating.

scholarly journals Microstructure, friction and corrosion resistance properties of a Ni–Co–Al2O3 composite coating

RSC Advances ◽  
2018 ◽  
Vol 8 (22) ◽  
pp. 12138-12145 ◽  
Author(s):  
Zong-wei Jia ◽  
Wan-chang Sun ◽  
Fang Guo ◽  
Ya-ru Dong ◽  
Xiao-jia Liu
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Composite Coating ◽  
Composite Coatings ◽  
Al2o3 Composite ◽  
Pulsed Electrodeposition

Ni–Co–Al2O3 composite coatings were prepared by pulsed electrodeposition and electrophoresis–electrodeposition on aluminum alloy.

Improvement of microstructure and properties of Ni–Al2O3 composite coating via jet electrodeposition

2020 ◽  
Vol 34 (27) ◽  
pp. 2050243
Author(s):  
Hui Fan ◽  
Jie Jiang ◽  
Yangpei Zhao ◽  
Shankui Wang ◽  
Zhijing Li
Keyword(s):  
Wear Rate ◽  
Surface Morphology ◽  
Composite Coating ◽  
Process Parameters ◽  
Current Density ◽  
Composite Coatings ◽  
Coating Structure ◽  
Mechanical And Tribological Properties ◽  
Al2o3 Composite ◽  
Jet Electrodeposition

Ni–Al2O3 composite coatings were prepared with a modified Watt’s bath by using jet electrodeposition method. As the key process parameter, current density and the addition of Al2O3 nanoparticles in electrolyte were studied about the effect on the surface morphology and co-deposition of Al2O3 nanoparticles of composite coating. The mechanical and tribological properties of the composite coating were also tested. The results show that properly increasing the current density and Al2O3 addition can increase the co-deposition of nanoparticles in the coating and promote the formation of a dense and refined coating structure. Using the optimized process parameters of current density (300 A/dm2) and Al2O3 addition (30 g/L), the co-deposition of Al2O3 in the composite coating can reach a maximum of 13.1 at.%. The hardness of the coating reaches the peak at 623 HV. The wear rate of the composite coating is also greatly reduced with optimized parameters.

Sign in / Sign up

Export Citation Format

Share Document