scholarly journals Performance Analysis of Highway Wind Turbine Enhanced with Wind Guide Vanes Using the Taguchi Method

CFD letters ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 25-42
Author(s):  
Mohamad Zahid Mazlan ◽  
Fazila Mohd Zawawi ◽  
Teeab Tahzib ◽  
Kamarulafizam Ismail ◽  
Syahrullail Samion
Keyword(s):  
Taguchi Method ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Guide Vane ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes ◽  
Moving Vehicle ◽  
Low Wind Speed

Considerable efforts have been made by researchers to study the interaction between moving vehicles and wind turbines. The Savonius vertical-axis wind turbine was chosen due to its effectiveness in low-wind speed conditions. Speeding vehicles produce a scattered and non-uniform wind flow with disturbances. Hence, to prevent a negative torque, a row of wind guide vane panels was arranged in front of the blades of a wind turbine. The wind guide vane had the shape of an NACA4412 aerofoil to reduce the loss of wind energy, and to further increase wind velocity. A number of CFD simulations were designed using the Taguchi method to determine the optimum conditions for the power coefficient of the wind turbine in terms of the effects of three factors, namely, the distance between the guide vanes (d), the angle of the guide vanes (?), and the speed of the moving car (VC). An orthogonal array of L9(33) was designed. In addition, to observe the effects of the wind velocity induced by the moving vehicle, the wind turbine was incorporated with one degree of freedom (1DOF). The results showed that the speed of the moving car played a major role in determining the power coefficient. The order of influence of each factor was ranked as VC > ? > d. The performance of the wind turbine was sensitive to the speed of the car and the angle of the guide vanes, whereas it was insensitive to the distance between the guide vanes. Furthermore, the analysis of the signal-to-noise (S/N) ratio suggested that the optimal combination of factors for a maximum power coefficient were d = 0.4m, ? = 30°, and VC =30m/s. The optimum setting increased the Cp to 26% compared to the Cp that was produced without the installation of the guide vanes.

Computational fluid dynamic analysis of roof-mounted vertical-axis wind turbine with diffuser shroud, flange, and vanes

2018 ◽  
Vol 42 (4) ◽  
pp. 404-415
Author(s):  
H. Abu-Thuraia ◽  
C. Aygun ◽  
M. Paraschivoiu ◽  
M.A. Allard
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Guide Vane ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes ◽  
Turbine Design

Advances in wind power and tidal power have matured considerably to offer clean and sustainable energy alternatives. Nevertheless, distributed small-scale energy production from wind in urban areas has been disappointing because of very low efficiencies of the turbines. A novel wind turbine design — a seven-bladed Savonius vertical-axis wind turbine (VAWT) that is horizontally oriented inside a diffuser shroud and mounted on top of a building — has been shown to overcome the drawback of low efficiency. The objective this study was to analyze the performance of this novel wind turbine design for different wind directions and for different guide vanes placed at the entrance of the diffuser shroud. The flow field over the turbine and guide vanes was analyzed using computational fluid dynamics (CFD) on a 3D grid for multiple tip-speed ratios (TSRs). Four wind directions and three guide-vane angles were analyzed. The wind-direction analysis indicates that the power coefficient decreases to about half when the wind is oriented at 45° to the main axis of the turbine. The analysis of the guide vanes indicates a maximum power coefficient of 0.33 at a vane angle of 55°.

Experimental Study of a Straight-Bladed Vertical Axis Wind Turbine With a Directed Guide Vane Row

2009 ◽  
Author(s):  
Manabu Takao ◽  
Hiroyuki Takita ◽  
Yohei Saito ◽  
Takao Maeda ◽  
Yasunari Kamada ◽  
...  
Keyword(s):  
Experimental Study ◽  
Wind Tunnel ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Guide Vane ◽  
Vertical Axis ◽  
Chord Length ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes ◽  
Blade Height

The objective of this study is to show the effect of guide vane geometry on the performance of wind turbine. In order to overcome the disadvantages of vertical axis wind turbine, a straight-bladed vertical axis wind turbine (S-VAWT) with a directed guide vane row has been proposed and tested by the authors. According to previous studies, it was clarified that the performance of the turbine can be improved by means of the directed guide vane row. However, the guide vane geometry of S-VAWT has not been optimized so far. In order to clarify the effect of guide vane geometry, the effects of distance between the guide vanes and the number of guide vanes on power and torque coefficients were investigated in the experiments. The experimental study was carried out by a wind tunnel. The wind tunnel with a diameter of 1.8m is open jet type. The wind velocity is from 5 to 9 m/s in the experiments. The rotor has three straight blades with a profile of NACA4518 and a chord length of 100 mm, a diameter of 0.6 m and a blade height of 0.7 m. The guide vane row consists of some arc plates.

Aerodynamic and aeroacoustic performance investigations on modified H-rotor Darrieus wind turbine

2021 ◽  
pp. 0309524X2110039
Author(s):  
Amgad Dessoky ◽  
Thorsten Lutz ◽  
Ewald Krämer
Keyword(s):  
Wind Turbine ◽  
High Speed ◽  
Cfd Simulation ◽  
Vertical Axis ◽  
3D Models ◽  
Power Coefficient ◽  
Design Parameters ◽  
Second Phase ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes

The present paper investigates the aerodynamic and aeroacoustic characteristics of the H-rotor Darrieus vertical axis wind turbine (VAWT) combined with very promising energy conversion and steering technology; a fixed guide-vanes. The main scope of the current work is to enhance the aerodynamic performance and assess the noise production accomplished with such enhancement. The studies are carried out in two phases; the first phase is a parametric 2D CFD simulation employing the unsteady Reynolds-averaged Navier-Stokes (URANS) approach to optimize the design parameters of the guide-vanes. The second phase is a 3D CFD simulation of the full turbine using a higher-order numerical scheme and a hybrid RANS/LES (DDES) method. The guide-vanes show a superior power augmentation, about 42% increase in the power coefficient at λ = 2.75, with a slightly noisy operation and completely change the signal directivity. A remarkable difference in power coefficient is observed between 2D and 3D models at the high-speed ratios stems from the 3D effect. As a result, a 3D simulation of the capped Darrieus turbine is carried out, and then a noise assessment of such configuration is assessed. The results show a 20% increase in power coefficient by using the cap, without significant change in the noise signal.

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

scholarly journals Preliminary Performance Tests and Simulation of a V-Shape Roof Guide Vane Mounted on an Eco-Roof System

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2846 ◽  
Author(s):  
Xiaohang Wang ◽  
Wentong Chong ◽  
Kokhoe Wong ◽  
Liphuat Saw ◽  
Sinchew Poh ◽  
...  
Keyword(s):  
Power Generation ◽  
Guide Vane ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Roof System ◽  
Low Wind Speed ◽  
Computational Fluid Dynamics Cfd ◽  
Power Generation System ◽  
Low Efficiency

The technical and economic features of a patented V-shape roof guide vane (VRGV) with a solar and wind power generation system mounted on an eco-roof system are presented in this paper. Moreover, this innovative VRGV was investigated on for the purpose of improving the performance of a vertical axis wind turbine (VAWT), which was installed on an eco-roof system to solve the low-efficiency power generation problem of the wind turbines under the condition of a low wind speed. This paper proposes a preliminary study for the performance of the VAWT with the VRGV on a building. This research used a mock-up building with a double slope roof, where a five straight-bladed VAWT was mounted and tested under two conditions, with and without the VRGV. From the comparative experiments, the self-starting performance and rotational speed of the VAWT mounted above a double slope roof with the VRGV have been significantly improved compared to the VAWT without the VRGV. Further, the power coefficient (Cp) of the VAWT can be augmented to about 71.2% increment due to the VRGV design. In addition, numerical simulations by computational fluid dynamics (CFD) were proposed to verify the augmented effect of the Cp of the VAWT under the influence of the VRGV in the experiment. Besides, economic estimation of the VRGV was conducted.

scholarly journals THE EFFECT OF DARRIEUS AND SAVONIUS WIND TURBINES POSITION ON THE PERFORMANCE OF THE HYBRID WIND TURBINE AT LOW WIND SPEED

2020 ◽  
Author(s):  
Nawfal M. Ali ◽  
Abdul Hassan A. K ◽  
Sattar Aljabair
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Aerodynamic Characteristics ◽  
The Other ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed ◽  
Turbine Model ◽  
Better Than

This paper presents an experimental and numerical simulation to investigate a hybrid vertical axis wind turbine model highly efficient which can be worked at low wind speed by studying the aerodynamic characteristics of four models of hybrid VAWTs. The hybrid WT consists of the SWT having two blades and the DWT type straight having two blades. Four models were constructed to study experimentally and numerically to choose the best model. Two models were DWT in the upper and SWT in the lower, also two models were SWT in the upper and DWT in the lower. The phase stage angle between the turbines is 0o and 90o . The experimental and numerical results showed that the performance of hybrid WT where DWT in the upper and SWT in the lower with phase stage 90o is better than in the other models, it can be started to work at a wind velocity of 2.2 m/s. At the wind velocity 3 m/s, the values of the parameters are the rotational speed (198 rpm), the CP (0.3195), the CT (0.2003), the TSR (1.6) and self-starting rotation at this value of wind velocity (3 m/s). The efficiency of extracting the wind power by hybrid WT is (51.2 %).

A Straight-Bladed Vertical Axis Wind Turbine With a Directed Guide Vane: Mechanism of Performance Improvement

2008 ◽  
Author(s):  
Hideki Kuma ◽  
Manabu Takao ◽  
Toshiyuki Beppu ◽  
Takao Maeda ◽  
Yasunari Kamada ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Performance Improvement ◽  
Aerodynamic Force ◽  
Guide Vane ◽  
Vortex Method ◽  
Vertical Axis ◽  
Rotor Blades ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Lagrangian Simulation

A straight-bladed vertical axis wind turbine with a directed guide vane has been proposed in order to enhance its torque. The experimental study of the proposed wind turbine was carried out by a wind tunnel with an outlet diameter of 1.8m. The tested rotor has 3 straight rotor blades with a profile of NACA0018, a radius of 0.35 m and a height of 0.7 m. The guide vane which consists of an arc plate rotates around the rotor and is directed to the wind by aerodynamic force generated by tail vanes, so as to put the guide vane in upstream of the rotor. As a result, the performance of the straight-bladed vertical axis turbine was improved by means of the directed guide vane and the power coefficient of the proposed wind turbine was approximately 1.2 times higher than that of the original wind turbine which has no guide vane. Further, flows around the proposed wind turbine have been investigated by use of the vortex method which provides a Lagrangian simulation of unsteady and vortical flows.

scholarly journals Blades Optimization for Maximum Power Output of Vertical Axis Wind Turbine

2021 ◽  
Vol 10 (3) ◽  
pp. 585-595
Author(s):  
Ahmad Adnan Shoukat ◽  
Adnan Aslam Noon ◽  
Muhammad Anwar ◽  
Hafiz Waqar Ahmed ◽  
Talha Irfan Khan ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Edge Length ◽  
Research Network ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed ◽  
Edge Profile ◽  
Power Yield

Wind power is a significant and urging sustainable power source asset to petroleum derivatives. Wind machines, for example, H-Darrieus vertical pivot wind turbines (VAWTs) have increased much notoriety in research network throughout the most recent couple of decades because of their applications at destinations having moderately low wind speed. Be that as it may, it is noticed that such wind turbines have low effectiveness. The point of this examination is to plan rotor cutting edges which could create most extreme power yield and execution. Different plan factors, for instance, harmony length, pitch edge, rotor distance across, cutting edge length and pitch point are explored to upgrade the presentation of VAWT. Rotor cutting edges are manufactured using the NACA-0030 structure and tried in wind burrow office and contrast its outcomes and DSM 523 profile. Numerical simulations are performed to get best geometry and stream conduct for achieving greatest power. It is seen that for higher tip-speed-proportion (TSR), shorter harmony length and bigger distance across the rotor (i.e., lower robustness) yields higher effectiveness in NACA 0030. Nevertheless, for lower TSR, the more drawn out agreement length and slighter distance across rotor (i.e., higher strength) gives better implementation. The pitch point is - 2° for TSR = 3 and - 3° for TSR = 2.5. The most extreme power yield of the wind turbine is acquired for the sharp edge profile NACA 0030. Besides, instantaneous control coefficient, power coefficient (CP) is the greatest reason for azimuthal edge of 245° and least esteem for 180°.

Novel Vertical-Axis Wind Turbine With Articulated Blading

2012 ◽  
Author(s):  
H. Jericha ◽  
E. Göttlich ◽  
T. Selic ◽  
W. Sanz
Keyword(s):  
Wind Turbine ◽  
Wind Direction ◽  
Vertical Axis ◽  
Bevel Gear ◽  
Power Coefficient ◽  
Return Flow ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes ◽  
Wide Range ◽  
Gear Box

In this work a novel vertical-axis wind turbine is presented which can catch a wide range of wind velocities at high efficiencies. The wind turbine consists of a rotatable horizontal platform, where three symmetric blades are arranged which rotate with half of the platform angular speed but in opposite direction relative to it. The rotation of the blades allows them to adapt to the varying angle of attack of the wind during one revolution of the platform. The important characteristic is the design feature that the blades are inclined outwards to the vertical axis of the platform by an angle of about 20 deg. The inclination leads to an increased circumferential velocity along the blade span, so that the increasing wind velocity with height can be better captured. Also the chord length of the blades increases with the spanwise position. In order to better utilize the wind flow, guide vanes can be arranged which increase the flow to those blades currently moving with the wind and in return flow can even give proper windshield. The articulated blades are connected to the horizontal platform via a special planetary bevel gear box, so that the relative rotational movement of them is controlled by the rotating platform, in fact a rotating gear box. This unit itself is connected to a generator thus producing electrical energy. The wind turbine can be tracked to a changed wind direction by means of rotating the stationary center bevel-gear wheel, which at given wind direction is then kept at constant position. In this paper the design of wind turbine is described in detail and the advantages of the novel vertical-axis turbine are discussed. First CFD investigations of a 2D section without guide vanes are presented. They show that maximum power can be achieved for a wide range of speed ratios. The calculated power coefficient is about 0.36, an interesting value for vertical-axis wind turbines.

A Straight-Bladed Vertical Axis Wind Turbine With a Directed Guide Vane Row

2007 ◽  
Author(s):  
Manabu Takao ◽  
Takao Maeda ◽  
Yasunari Kamada ◽  
Michiaki Oki ◽  
Hideki Kuma
Keyword(s):  
Experimental Study ◽  
Wind Tunnel ◽  
Wind Turbine ◽  
Aerodynamic Force ◽  
Guide Vane ◽  
Vertical Axis ◽  
Rotor Blades ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Turbine

A straight-bladed vertical axis wind turbine with a directed guide vane row has been proposed in order to enhance its torque. The experimental study of the proposed wind turbine was carried out by a wind tunnel with an outlet diameter of 1.8m. The tested rotor has some straight rotor blades with a profile of NACA0015, a radius diameter of 0.3 m and a height of 0.7 m. The guide vane row having 3 arc plates rotates around the rotor and is directed to the wind by aerodynamic force generated by tail vanes, so as to put the guide vane row in upstream of the rotor. As a result, the performance of the straight-bladed vertical axis turbine was improved by means of the directed guide vane row. Further, by the use of the guide vane row adopted in the study, the power coefficient of the proposed wind turbine was approximately 1.5 times higher than that of the original wind turbine which has no guide vane.

Sign in / Sign up

Export Citation Format

Share Document