scholarly journals A STUDY OF HIGH LIFT AERODYNAMIC DEVICES ON COMMERCIAL AIRCRAFTS

Aviation ◽  
2020 ◽  
Vol 24 (3) ◽  
pp. 123-136
Author(s):  
Swamy Naidu Venkata Neigapula ◽  
Satya Prasad Maddula ◽  
Vasishta Bhargava Nukala
Keyword(s):  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Trailing Edge ◽  
High Lift ◽  
Aircraft Wings ◽  
Surface Pressure Distribution ◽  
Trailing Edge Flaps ◽  
Stall Angle ◽  
Kinematic Mechanisms

Aerodynamic performance of aircraft wings vary with flight path conditions and depend on efficiency of high lift systems. In this work, a study on high lift devices and mechanisms that aim to increase maximum lift coefficient and reduce drag on commercial aircraft wings is discussed. Typically, such extensions are provided to main airfoil along span wise direction of wing and can increase lift coefficient by more than 100% during operation. Increasing the no of trailing edge flaps in chord wise direction could result in 100% increment in lift coefficient at a given angle of attack but leading edge slats improve lift by delaying the flow separation near stall angle of attack. Different combinations of trailing edge flaps used by Airbus, Boeing and McDonnel Douglas manufacturers are explained along with kinematic mechanisms to deploy them. The surface pressure distribution for 30P30N airfoil is evaluated using 2D vortex panel method and effects of chord wise boundary layer flow transitions on aerodynamic lift generation is discussed. The results showed better agreements with experiment data for high Reynolds number (9 million) flow conditions near stall angle of attack.

scholarly journals Design and Validation of a New Morphing Camber System by Testing in the Price—Païdoussis Subsonic Wind Tunnel

Aerospace ◽  
2020 ◽  
Vol 7 (3) ◽  
pp. 23 ◽  
Author(s):  
David Communier ◽  
Ruxandra Mihaela Botez ◽  
Tony Wong
Keyword(s):  
Wind Tunnel ◽  
Unmanned Aerial Vehicle ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Trailing Edge ◽  
Subsonic Wind Tunnel ◽  
Aerial Vehicle ◽  
Stall Angle

This paper presents the design and wind tunnel testing of a morphing camber system and an estimation of performances on an unmanned aerial vehicle. The morphing camber system is a combination of two subsystems: the morphing trailing edge and the morphing leading edge. Results of the present study show that the aerodynamics effects of the two subsystems are combined, without interfering with each other on the wing. The morphing camber system acts only on the lift coefficient at a 0° angle of attack when morphing the trailing edge, and only on the stall angle when morphing the leading edge. The behavior of the aerodynamics performances from the MTE and the MLE should allow individual control of the morphing camber trailing and leading edges. The estimation of the performances of the morphing camber on an unmanned aerial vehicle indicates that the morphing of the camber allows a drag reduction. This result is due to the smaller angle of attack needed for an unmanned aerial vehicle equipped with the morphing camber system than an unmanned aerial vehicle equipped with classical aileron. In the case study, the morphing camber system was found to allow a reduction of the drag when the lift coefficient was higher than 0.48.

Effect of Leading Edge Blowing Slots on Stall Angles of a 10:1 Elliptical Airfoil

2010 ◽  
Author(s):  
Jonathan Kweder ◽  
Mary Ann Clarke ◽  
James E. Smith
Keyword(s):  
Aspect Ratio ◽  
Closed Loop ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Circulation Control ◽  
West Virginia University ◽  
Trailing Edge ◽  
Wind Speeds ◽  
Stall Angle

Traditional uses of circulation control have been studied since the early 1960’s and have been developed primarily using trailing edge slots over a rounded trailing edge in order to take advantage of the Coanda˘ effect. The leading edge activated slots allow jets of air to enter the freestream flowing around the airfoil thus enhancing the energy of the lift force. The main purpose of circulation control for fixed wing aircraft is to increase the lifting force when large lifting forces and/or slow speeds are required, such as at take-off and landing. While there is a significant increase in the lifting forces achievable through the use of circulation control, there is also an inherent increase in the drag force on the airfoil (Abramson, 2004, Loth, 1976, 1984). Current effects of circulation control on stall angles of airfoils are not well documented and thus needs to be studied. Stall occurs when a sudden reduction in lift occurs caused by a flow separation between the incoming air flow and the lifting surface. The angle at which this happens is commonly called the critical angle of attack, and is typically between eight and twenty degrees depending on the wing profile, aspect ratio, camber, and planform area. For this study, a 10:1 aspect ratio elliptical airfoil with a chord length of 11.8 inches and a span of 31.5 inches was inserted into the West Virginia University Closed Loop Wind Tunnel and was tested at varying wind speeds (80, 100, and 120 feet per second), angle of attack (zero to sixteen degrees), and blowing coefficients, ranging from 0.0006 to 0.0127 depending on internal plenum pressure. By comparing the non-circulation controlled wing with the active leading edge slot circulation control data, a trend was found as to the influence of the circulation control exit jet on the stall characteristics of the wing. For this specific case, when the circulation control is in use on the 10:1 elliptical airfoil, the stall angle decreases, from eight degrees to six degrees, while providing up to a 46% increase in lift coefficient.

Elliptic Airfoil Stall Analysis With Trailing Edge Slots

2010 ◽  
Author(s):  
Jonathan Kweder ◽  
Mary Ann Clarke ◽  
James E. Smith
Keyword(s):  
Lift Coefficient ◽  
Leading Edge ◽  
Surface Velocity ◽  
Circulation Control ◽  
West Virginia University ◽  
Trailing Edge ◽  
Near Surface ◽  
Wind Speeds ◽  
Edge Location ◽  
Stall Angle

Circulation control (CC) is a high-lift methodology that can be used on a variety of aerodynamic applications. This technology has been in the research and development phase for over sixty years primarily for fixed wing aircraft where the early models were referred to as “blown flaps”. Circulation control works by increasing the near surface velocity of the airflow over the leading edge and/or trailing edge of a lifting surface This phenomenon keeps the boundary layer jet attached to the wing surface thus increasing the lift generated on the surface. The circulation control airflow adds energy to the lift force through conventional airfoil lift production and by altering the circulation of stream lines around the airfoil. For this study, a 10:1 aspect ratio elliptical airfoil with a chord length of 11.8 inches and a span of 31.5 inches was inserted into the West Virginia University Closed Loop Wind Tunnel and was tested at varying wind speeds (80, 100, and 120 feet per second), angle of attack (zero to sixteen degrees), and blowing coefficients, ranging from 0.0006 to 0.0127 depending on plenum pressure. By comparing the non-circulation controlled wing with the active circulation control data, a trend was found as to the influence of circulation control on the stall characteristics of the wing for trailing edge active control. For this specific case, when the circulation control is in use on the 10:1 elliptical airfoil, the stall angle decreased, from eight degrees to six degrees, while providing a 70% increase in lift coefficient. It should be noted that due to the trailing edge location of the circulation control exit jet, a “virtual” camber is created with the free stream air adding length to the overall airfoil. Due to this phenomena, the actual stall angle measured increased from eight degrees on the un-augmented airfoil, to a maximum of twelve degrees.

The Dassault Mirage G

1969 ◽  
Vol 73 (708) ◽  
pp. 1027-1028
Author(s):  
Henri Deplante
Keyword(s):  
Leading Edge ◽  
Variable Geometry ◽  
Relative Thickness ◽  
Trailing Edge ◽  
High Lift ◽  
Profound Knowledge ◽  
Subsonic Speed ◽  
Trailing Edge Flaps ◽  
Leading Edge Slats

The interest of wings with variable sweepback springs directly from pure commonsense and appeals to no profound knowledge of aerodynamics for its justification. To realise the advantage of variable geometry, it is enough to know that only a wing of small relative thickness is capable of good performance at supersonic speeds and that by increasing the sweepback from 20° to 70° the thickness of a wing is divided by about 2. In the advanced position, the wing offers its full span to the airstream and with high-lift devices in action (leading-edge slats and trailing-edge flaps combined), the aeroplane can develop the considerable lift necessary for take-off and landing as well as for break-through and for slow approach. Wings still advanced but slats, flaps and undercarriage retracted, the aeroplane is in excellent maximum fineness condition for protracted cruising at subsonic speed or for a long wait. As soon as transonic (Mach No of more than 0-8) or supersonic speeds are in question, the wings are progressively folded back.

Aerodynamic Aspects of Boundary Layer Control for High Lift at Low Speeds

1963 ◽  
Vol 67 (628) ◽  
pp. 201-223 ◽  
Author(s):  
John Williams ◽  
Sidney F. J. Butler
Keyword(s):  
Boundary Layer ◽  
Leading Edge ◽  
Boundary Layer Control ◽  
Trailing Edge ◽  
High Lift ◽  
Air Jets ◽  
Slot Suction ◽  
Trailing Edge Flaps ◽  
Trailing Edge Flap ◽  
Layer Control

Summary:The usefulness of boundary-layer control (B.L.C.) at the knee of a trailing-edge flap, over the wing nose close to the leading-edge or at the knee of a leading-edge flap is first noted. Various methods of providing B.L.C. are outlined, comprising slot blowing, slot suction, area suction, inclined air-jets, and specially-designed aerofoil shapes. The aerodynamic aspects of slot blowing over trailing-edge flaps and the wing nose are then examined in detail and both slot suction and area suction are also considered. The associated practical design features required for good performance are discussed and some flight-handling implications are mentioned.

Numerical Study on Aerodynamic Characteristics of NACA0015

2013 ◽  
Vol 302 ◽  
pp. 640-645
Author(s):  
Su Jeong Lee ◽  
Eui Chul Jeong ◽  
Hee Chang Lim
Keyword(s):  
Pressure Distribution ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Aerodynamic Characteristics ◽  
Surface Pressure Distribution ◽  
Maximum Value ◽  
Stall Angle ◽  
Near Wall

In this study, a numerical simulation is made to understand the effect of the angle of attack on a NACA airfoil, which will be used for a basic shape to apply for making the vertical axis Darius wind turbine. The near-wall y+ value which is less than 1 is known to be most desirable for a near-wall modeling. Therefore, this study is aiming to observe the variation and find the optimized value of y+. The Reynolds number used in this study was 360,000, where the chord length and the velocity were 0.12m and 43.8m/s, respectively. Generally, the lift coefficient of the airfoil tends to increase as the angle of attack increases and it decreases substantially at the stall angle and then it decreases. As expected, the lift coefficient increases rapidly from 0 to 10° and then after the sudden drop of the lift (i.e., the stall) at around 10 to 16° depending on the y+ value. In this paper, it seems to be reliable and appropriate to use y+ value close to 1. From the surface pressure distribution, from the result obtained the ratio of pressure distribution of maximum value to the minimum value was 1.89and these peaks move forward to backward as the angle of attack increases.

High-Lift Mechanism of a Bionic Slat

2013 ◽  
Vol 461 ◽  
pp. 220-229
Author(s):  
Chang Jiang Ge ◽  
Mei Chen Ge
Keyword(s):  
Flow Field ◽  
Pressure Gradient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Element Model ◽  
Broadband Noise ◽  
High Lift ◽  
Edge Separation

To avoid broadband noise from a slat cove, the deployed slat contour is usually modified by filling cove, but the design is sensitive to aerodynamic performance. In the paper, a bionic slat without a cove is built on the basis of a bionic airfoil (i.e. stowed bionic multi-element airfoil), which is extracted from a long-eared owl wing. The quasi-two-dimensional models with a deployed bionic slat and a stowed bionic slat are manufactured by rapid manufacturing and prototyping system, respectively, and measured in a low-turbulence wind tunnel. The results are used to characterize high-lift effect: the lift coefficients of the model with a stowed slat are larger at less than 4°angle of attack, but the model with a deployed slat has the larger lift coefficients at greater than 4°angle of attack. Furthermore, the deployed bionic slat can increase stall angle and maximum lift coefficient, but also delay the decline of the lift coefficient curve slope meaning that the leading-edge separation is postponed within a certain range of angle of attack. At the same time, the flow field around the models is visualized by smoke wire method. The leading-edge separation of the model with a stowed slat is shown at low Reynolds number and angle of attack. However, the finding does not occur in the flow field of the model with a deployed slat at the same conditions, probably because the gap between the bionic slat and the main wing results in favorable pressure gradient, the deployed bionic slat decreases the peak of adverse pressure gradient by increasing the chord of the bionic multi-element model, and the bionic slat wake excites transition to the boundary layer on upper surface of the main wing. This superiority may be used as reference in the design of the leading-edge slat without a cove.

Performance Improvement of a Wind Turbine Blade Designed for Low Wind Speeds With a Passive Trailing Edge Flap

2012 ◽  
Author(s):  
Mohammed Rafiuddin Ahmed ◽  
Epeli Nabolaniwaqa
Keyword(s):  
Wind Turbines ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Suction Surface ◽  
Trailing Edge ◽  
Wind Speeds ◽  
Trailing Edge Flaps ◽  
Low Wind Speeds ◽  
Lift And Drag

The flow characteristics and the lift and drag behavior of a newly designed thick trailing-edged airfoil that was provided with fixed trailing edge flaps (Gurney flaps) of 1% to 5% height right at the back of the airfoil were studied at different low Reynolds numbers (Re) and angles of attack for possible applications in wind turbines suitable for the wind speeds of 4–6 m/s that are common in the Pacific Island Countries. A thick trailing-edged blade section, AF300, that was designed and tested in a recent work for small horizontal axis wind turbines to improve the turbine’s startup and performance at low wind speeds was chosen for this study. Experiments were performed on the AF300 airfoil in a wind tunnel at different Re, flap heights and angles of attack. Pressure distributions were obtained across the surface of the airfoil and the lift and drag forces were measured for different cases. It was found that the flap considerably improves the suction on the upper surface of the airfoil resulting in a high lift coefficient. For some of the angles, in the case of 3 mm and 4 mm flaps, the peak Cp values on the suction surface were significantly higher compared to those without the flap. However, at angles of attack of 12° and above, this unusually high Cp on the upper surface close to the leading edge caused flow separation for some cases as the flow could not withstand the strong adverse pressure gradient. The CFX results matched most of the experimental results without flaps, except that the suction peak was lower numerically. The difference was higher for the case with flaps. It is clear from the results that trailing-edge flaps can be used to improve the performance of small wind turbines designed for low wind speeds.

scholarly journals A Parametric Study of Trailing Edge Flap Implementation on Three Different Airfoils Through an Artificial Neuronal Network

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 828
Author(s):  
Igor Rodriguez-Eguia ◽  
Iñigo Errasti ◽  
Unai Fernandez-Gamiz ◽  
Jesús María Blanco ◽  
Ekaitz Zulueta ◽  
...  
Keyword(s):  
Aerodynamic Coefficients ◽  
Trailing Edge ◽  
High Lift ◽  
Trailing Edge Flaps ◽  
Artificial Neural Network Ann ◽  
Lift And Drag ◽  
Artificial Neuronal Network ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Trailing edge flaps (TEFs) are high-lift devices that generate changes in the lift and drag coefficients of an airfoil. A large number of 2D simulations are performed in this study, in order to measure these changes in aerodynamic coefficients and to analyze them for a given Reynolds number. Three different airfoils, namely NACA 0012, NACA 64(3)-618, and S810, are studied in relation to three combinations of the following parameters: angle of attack, flap angle (deflection), and flaplength. Results are in concordance with the aerodynamic results expected when studying a TEF on an airfoil, showing the effect exerted by the three parameters on both aerodynamic coefficients lift and drag. Depending on whether the airfoil flap is deployed on either the pressure zone or the suction zone, the lift-to-drag ratio, CL/CD, will increase or decrease, respectively. Besides, the use of a larger flap length will increase the higher values and decrease the lower values of the CL/CD ratio. In addition, an artificial neural network (ANN) based prediction model for aerodynamic forces was built through the results obtained from the research.

scholarly journals Analysis and Design of a Leading Edge with Morphing Capabilities for the Wing of a Regional Aircraft—Gapless Chord- and Camber-Increase for High-Lift Performance

2021 ◽  
Vol 11 (6) ◽  
pp. 2752
Author(s):  
Conchin Contell Asins ◽  
Volker Landersheim ◽  
Dominik Laveuve ◽  
Seiji Adachi ◽  
Michael May ◽  
...  
Keyword(s):  
Leading Edge ◽  
Bird Strike ◽  
High Lift ◽  
Analysis And Design ◽  
Actuation System ◽  
Aerodynamic Properties ◽  
Reinforced Plastic ◽  
Stall Angle ◽  
Carbon Fibre Reinforced Plastic ◽  
Electromechanical Actuation

In order to contribute to achieving noise and emission reduction goals, Fraunhofer and Airbus deal with the development of a morphing leading edge (MLE) as a high lift device for aircraft. Within the European research program “Clean Sky 2”, a morphing leading edge with gapless chord- and camber-increase for high-lift performance was developed. The MLE is able to morph into two different aerofoils—one for cruise and one for take-off/landing, the latter increasing lift and stall angle over the former. The shape flexibility is realised by a carbon fibre reinforced plastic (CFRP) skin optimised for bending and a sliding contact at the bottom. The material is selected in terms of type, thickness, and lay-up including ply-wise fibre orientation based on numerical simulation and material tests. The MLE is driven by an internal electromechanical actuation system. Load introduction into the skin is realised by span-wise stringers, which require specific stiffness and thermal expansion properties for this task. To avoid the penetration of a bird into the front spar of the wing in case of bird strike, a bird strike protection structure is proposed and analysed. In this paper, the designed MLE including aerodynamic properties, composite skin structure, actuation system, and bird strike behaviour is described and analysed.

Sign in / Sign up

Export Citation Format

Share Document