Experimental Investigation and Finite Element Analysis on Electromagnetic Compression Forming Processed Aluminum Alloy Tubes

2011 ◽  
Vol 110-116 ◽  
pp. 1706-1710
Author(s):  
Selvam Rajiv ◽  
Karibeeran Shanmuga Sundaram ◽  
Pablo Pasquale
Keyword(s):  
Experimental Investigation ◽  
Finite Element ◽  
Aluminum Alloy ◽  
High Speed ◽  
High Energy ◽  
Work Piece ◽  
Outer Diameter ◽  
Forming Process ◽  
Element Analysis ◽  
Electromagnetic Compression

Electromagnetic forming (EMF) is a high energy rate forming (HERF) process. It is a high speed forming process using a pulsed magnetic field to form work pieces made of metals such as copper or aluminum alloys with high electrical conductivity. The work piece to be deformed will be located within the effective area of the tool coil so that the resulting type of stress during the forming process is determined by the type of coil used and its arrangement as related to the component. Tubular or structural components can be narrowed by means of compression coils or widened by means of expansion coils, where as sheet metal can be deformed by flat coils. In this work, the experimental investigation and simulation of electromagnetic compression forming of aluminum alloy tubes is studied. The aim of the paper was to verify the results from Finite element methods with experimental data. Experiments were conducted on Tubes of outer diameter 40 mm and wall thickness of 2 mm with a nominal tensile strength of 214 MPa. The tube was compressed using a 4 turn helical actuator discharge that can be energied up to 20 kJ. A field shaper made of aluminum was used. A Maximum reduction of 15.85% in diameters were measured. The same problem was simulated in ANSYS using static coupled electromagnetic analysis. The results of the Simulation showed good correlation with experimental results.

A Study and Analysis on Electromagnetic Compression Forming Processed Aluminum Alloy Tubes

2011 ◽  
Vol 337 ◽  
pp. 560-563
Author(s):  
Selvam Rajiv ◽  
Karibeeran Shanmuga Sundaram ◽  
Pablo Pasquale
Keyword(s):  
Aluminum Alloy ◽  
Mathematical Analysis ◽  
High Speed ◽  
High Rate ◽  
Outer Diameter ◽  
Forming Process ◽  
High Speed Forming ◽  
Forming Characteristics ◽  
Forming Methods ◽  
Electromagnetic Compression

Electromagnetic forming is one of the high- rate forming methods that are extensively used to form and join axisymmetric tubes and metal sheet. It is a high speed forming process using a pulsed magnetic field to form work pieces made of metals such as copper or aluminum alloys with high electrical conductivity. In this work, the experimental investigation and mathematical analysis of electromagnetic compression forming of aluminum alloy tubes AA6063 is studied. The aim of the work was to verify the results from MATLAB code with the experimental data. Experiments were conducted on aluminum alloy AA6063 tubes of outer diameter 40 mm and wall thickness of 2 mm with a nominal tensile strength of 214 MPa. The tube was compressed using 4 turn helical actuator discharge coil that can be energized up to 20 kJ. A study on the post forming characteristics hardness and on metallurgical effects were also carried out. The results of the mathematical analysis using MATLAB 2010 showed good correlation with experimental results.

Finite Element Analysis for Comprehensive Residual Stress of 7075 Aluminum Alloy Thick Plate

2010 ◽  
Vol 154-155 ◽  
pp. 1255-1261
Author(s):  
Hai Yan Li ◽  
Yi Du Zhang ◽  
Hong Wei Zhang
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Aluminum Alloy ◽  
Thick Plate ◽  
Coupling Effect ◽  
Element Model ◽  
Forming Process ◽  
Element Analysis ◽  
Field Coupling ◽  
Simulation And Experiment

Based on “physical field coupling” finite element method, the generation of residual stress and interactive coupling effect were analyzed during the forming process of aluminum alloy thick-plate. Therefore, comprehensive residual stress generated from rolling, quenching and stretching was obtained. The finite element model was proved effective by comparing the results of simulation and experiment. Results show that percent reduction has significant influence to the distribution and magnitude of rolling stress; There is a coupling effect between rolling stress and quenching stress, which represents a basic state; Furthermore, after stretching the distribution of coupling stress remains, but the value reduces greatly; The residual stress has got the minimum, when stretching is near 3%.

scholarly journals Investigating of Mechanical Behavior of AA5083 in the Pressing Process Using Finite Element Analysis

2017 ◽  
Vol 11 (9) ◽  
pp. 51
Author(s):  
Babak Beglarzadeh ◽  
Behnam Davoodi
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Aluminum Alloy ◽  
Friction Stress ◽  
Forming Process ◽  
Element Analysis ◽  
Cold Forming ◽  
Aluminum Alloy 5083 ◽  
And Control

The process of cold forming is considered of the most different industries and the use of such process in the manufacture of components and small parts has expanded. Therefore, analyzing the behavior of metals in this process to identify and control durability that is the main factor of limiting process has particular importance in industrial forming processes. In this study, cold forming process of aluminum metal has been studied and its effect on its mechanical properties has been evaluated. For this purpose, first modeling piece of aluminum alloy 5083 for cold forming process is carried out and using finite element analysis, mechanical properties of considered piece during cold forming processes are investigated. The results show that by reducing friction, stress and strain during the process will reduce, thereby durability of the piece increases, or in other words, ductile fracture occurs in longer life and higher stresses. The results show that by proper forming operations, it can be improved the strength and durability of aluminum alloy. Finally, validation of results, by comparing simulation results with experimental results is carried out.

scholarly journals Finite Element Analysis of Extrusion Process for Magnesium Alloy Internal Threads with Electromagnetic Induction-Assisted Heating and Thread Performance Research

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2170 ◽  
Author(s):  
Meng Liu ◽  
Zesheng Ji ◽  
Rui Fan ◽  
Xingguo Wang
Keyword(s):  
Finite Element ◽  
Magnesium Alloy ◽  
Electromagnetic Induction ◽  
High Speed ◽  
Heating Temperature ◽  
Equivalent Stress ◽  
Hole Diameter ◽  
Process Conditions ◽  
Forming Process ◽  
Element Analysis

The casting magnesium alloy AZ91D cannot be extruded at room temperature. This paper presents a process for extruding internal threads using AZ91D heated by electromagnetic induction. The feasibility of the process is verified by finite element simulation and experiments. Using DEFORM-3D to simulate the process of extruding a M12 × 1.25 mm threaded hole by electromagnetic induction-assisted heating, the equivalent stress-strain and material flow law in the process of thread deformation was analyzed and verified by experiments. Three parameters—hole diameter, machine speed and heating temperature—were considered to study the influence of different process conditions on the forming torque. The results show that a heating temperature above 523 K can improve the plasticity of AZ91D. The hole diameter has an important influence on the forming torque. The forming process is not suitable for high-speed machining. The surface metal of the thread formed by this process has a strong deformation layer, which can improve the strength and hardness of the thread.

Computer Simulation of Deep Drawing Process for a Laminated Composite Cup

2007 ◽  
Author(s):  
Tushar Naik ◽  
Zhong Hu
Keyword(s):  
Finite Element ◽  
Aluminum Alloy ◽  
Deep Drawing ◽  
Laminated Composites ◽  
Laminated Composite ◽  
Element Model ◽  
Drawing Process ◽  
Forming Process ◽  
Element Analysis ◽  
Deep Drawing Process

The anisotropic nature of laminated composites creates a unique opportunity and also a great challenge for tailoring their behavior during the forming processes according to the design requirements. In this work, design and simulation of a deep drawing process for fiber-reinforced laminated composites were conducted by using finite element analysis. The effects of the fiber orientation and stacking order on the deep drawing process were investigated based on the basic understanding of forming process of the isotropic aluminum alloy (Al-1100) and laminated composite material (Grilon RVZ-15H nylon/glass). A three dimensional finite element model incorporating layered structural laminates with various fiber orientations was developed. The load-stroke relationship, changes in thickness, and stress-strain distribution were investigated and compared for both aluminum alloy and laminated composites of [0]12, [0/90]6 and [0/90/45/135]3, which can be employed for detailed design and process optimization.

On Saw-Tooth Chip Formation in High Speed Cutting GH4169

2007 ◽  
Vol 10-12 ◽  
pp. 359-363 ◽  
Author(s):  
Dong Jin Zhang ◽  
Gang Liu ◽  
X. Sun ◽  
Ming Chen
Keyword(s):  
Finite Element ◽  
High Speed ◽  
Cutting Speed ◽  
Chip Morphology ◽  
High Yield ◽  
Forming Process ◽  
Element Analysis ◽  
High Speed Cutting ◽  
Nickel Based Superalloy ◽  
Wide Range

The nickel-based superalloy GH4169 is a typical difficult-to-cut material, but it has been used in a good many kinds of aeronautical key structures because of its high yield stress and anti-fatigue performance at the temperature below 650°C. In this paper, finite element method (FEM) was introduced to study the saw-tooth chip forming process in detail when machining nickel-based superalloy GH4169. By the way of Lagrangian visco-elastic plastic approach, adiabatic shear band (ASB) was simulated in high speed machining condition by general commercial finite element code, and the mechanism of the adiabatic shearing phenomenon at primary shear zone was analyzed with the help of finite element analysis (FEA). The comprehensive comparisons of saw-tooth chip morphology under a wide range of cutting speed were also presented.

scholarly journals Through-Process Finite Element Modeling for Warm Flanging Process of Large-Diameter Aluminum Alloy Shell of Gas Insulated (Metal-Enclosed) Switchgear

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1784
Author(s):  
Da-Wei Zhang ◽  
Tian-Lin Shi ◽  
Sheng-Dun Zhao
Keyword(s):  
Finite Element ◽  
Aluminum Alloy ◽  
Temperature Field ◽  
Large Diameter ◽  
Outer Diameter ◽  
Fe Model ◽  
Fe Modeling ◽  
Forming Process ◽  
Forming Characteristics ◽  
Forming Defects

The large diameter metal shell component (LDMSC) is an important part of gas insulated (metal-enclosed) switchgear (GIS). The LDMSC with multi branches is filled with gas under certain pressure. The plastic forming process is an efficient approach to manufacturing the high reliability LDMSC. The warm flanging process has been widely used to form LDMSC using aluminum alloy. The forming process is characterized by local heating, and the distribution of temperature is strongly inhomogeneous. Although the wall thickness of the shell is 10 mm to 20 mm, the ratio of outer diameter to thickness is more than 40. These present some difficulties in the flanging process and result in some forming defects. Detailed forming characteristics are hard to obtain by analytical and experimental methods. Thus, the through-process finite element (FE) modeling considering heating, forming, unloading, and cooling is one of the key problems to research the manufacturing process of LDMSC. In this study, the through-process FE modeling of the warm flanging process of LDMSC using aluminum alloy was carried out based on the FORGE. The thermo-mechanical coupled finite element method was adopted in the modeling, and the deformation of the workpiece and the die stress were considered together in the modeling. A full three-dimensional (3D) geometry was modeled due to inhomogeneous distribution in all directions for the temperature field. The simulation data of local flame heating could be transferred seamlessly to the simulations of the deforming process, the unloading process, and the cooling process in the through-process FE model. The model was validated by comparison with geometric shapes and forming defects obtained from the experiment. The developed FE model could describe the inhomogeneous temperature field along circumferential, radial, and axial directions for the formed branch as well as the deformation characteristic and the unloading behavior during the warm flanging process. By using the FE model, the forming defects during the flanging process and their controlling characteristics were explored, the evolution of the temperature field through the whole process was studied, and deformation and springback characteristics were analyzed. The results of this study provide a basis for investigating deformation mechanisms, optimizing processes, and determining parameters in the warm flanging process of a large-diameter aluminum alloy shell component.

scholarly journals Are Suprapectineal Quadrilateral Surface Buttressing Plates Performances Superior to Traditional Fixation? A Finite Element Analysis

2021 ◽  
Vol 11 (2) ◽  
pp. 858
Author(s):  
Mara Terzini ◽  
Andrea Di Pietro ◽  
Alessandro Aprato ◽  
Stefano Artiaco ◽  
Alessandro Massè ◽  
...  
Keyword(s):  
Finite Element ◽  
Movement Analysis ◽  
High Energy ◽  
Clinical Analysis ◽  
Acetabular Fractures ◽  
Element Analysis ◽  
Bone Stress ◽  
Interfragmentary Movement ◽  
Element Approach ◽  
Transverse Fractures

Acetabular fractures have a high impact on patient’s quality of life, and because acetabular fractures are high energy injuries, they often co-occur with other pathologies such as damage to cartilage that could increase related morbidity; thus, it appears of primary importance developing reliable treatments for this disease. This work aims at the evaluation of the biomechanical performances of non-conservative treatments of acetabular fractures through a finite element approach. Two pelvic plates models (the standard suprapectineal plate—SPP, and a suprapectineal quadrilateral surface buttressing plate—SQBP) were analyzed when implanted on transverse or T-shaped fractures. The plates geometries were adapted to the specific hemipelvis, mimicking the bending action that the surgeon performs on the plate intraoperatively. Implemented models were tested in a single leg stance condition. The obtained results show that using the SQBP plate in transverse and T-shaped acetabular fractures generates lower bone stress if compared to the SPP plate. Interfragmentary movement analysis shows that the SQBP plate guarantees greater stability in transverse fractures. In conclusion, the SQBP plate seems worthy of further clinical analysis, having resulted as a promising option in the treatment of transverse and T-shaped acetabular fractures, able to reduce bone stress values and to get performances comparable, and in some cases superior, to traditional fixation.

Sign in / Sign up

Export Citation Format

Share Document