Finite Element Analysis for Comprehensive Residual Stress of 7075 Aluminum Alloy Thick Plate

2010 ◽  
Vol 154-155 ◽  
pp. 1255-1261
Author(s):  
Hai Yan Li ◽  
Yi Du Zhang ◽  
Hong Wei Zhang
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Aluminum Alloy ◽  
Thick Plate ◽  
Coupling Effect ◽  
Element Model ◽  
Forming Process ◽  
Element Analysis ◽  
Field Coupling ◽  
Simulation And Experiment

Based on “physical field coupling” finite element method, the generation of residual stress and interactive coupling effect were analyzed during the forming process of aluminum alloy thick-plate. Therefore, comprehensive residual stress generated from rolling, quenching and stretching was obtained. The finite element model was proved effective by comparing the results of simulation and experiment. Results show that percent reduction has significant influence to the distribution and magnitude of rolling stress; There is a coupling effect between rolling stress and quenching stress, which represents a basic state; Furthermore, after stretching the distribution of coupling stress remains, but the value reduces greatly; The residual stress has got the minimum, when stretching is near 3%.

Computer Simulation of Deep Drawing Process for a Laminated Composite Cup

2007 ◽  
Author(s):  
Tushar Naik ◽  
Zhong Hu
Keyword(s):  
Finite Element ◽  
Aluminum Alloy ◽  
Deep Drawing ◽  
Laminated Composites ◽  
Laminated Composite ◽  
Element Model ◽  
Drawing Process ◽  
Forming Process ◽  
Element Analysis ◽  
Deep Drawing Process

The anisotropic nature of laminated composites creates a unique opportunity and also a great challenge for tailoring their behavior during the forming processes according to the design requirements. In this work, design and simulation of a deep drawing process for fiber-reinforced laminated composites were conducted by using finite element analysis. The effects of the fiber orientation and stacking order on the deep drawing process were investigated based on the basic understanding of forming process of the isotropic aluminum alloy (Al-1100) and laminated composite material (Grilon RVZ-15H nylon/glass). A three dimensional finite element model incorporating layered structural laminates with various fiber orientations was developed. The load-stroke relationship, changes in thickness, and stress-strain distribution were investigated and compared for both aluminum alloy and laminated composites of [0]12, [0/90]6 and [0/90/45/135]3, which can be employed for detailed design and process optimization.

Finite Element Analysis on Residual Stress of Laser Brazing Diamond Wheel

2013 ◽  
Vol 712-715 ◽  
pp. 739-742 ◽  
Author(s):  
Zhi Bo Yang ◽  
Pei Fei Luo
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Element Model ◽  
Processing Parameters ◽  
Diamond Wheel ◽  
Laser Brazing ◽  
Element Analysis ◽  
The Matrix ◽  
Simulation And Experiment ◽  
Field Element

The purpose of this paper is to simulate the residual field of laser brazing by FEM of ANSYS. The 2-D coupled field element is elected to create finite element model. The brazing experiments have been done by means of 45steel which is the matrix and Ni-Cr solder and the residual stress of the diamond wheel has been measured by Raman method. The results of measure show that the maximum stress value is less strength of diamond. The residual stress distribution is basically identical between the results of simulation and experiment. According to this paper, it is possible to decrease the costs of study by selecting reasonable processing parameters on laser brazing.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

Research on the Effects of Welding Sequence on Welding Residual Stress of High-Speed Train Based on SYSWELD

2011 ◽  
Vol 399-401 ◽  
pp. 1806-1811
Author(s):  
Yong Hong Chen ◽  
Peng Chen ◽  
Ai Qin Tian
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
High Speed ◽  
Element Model ◽  
Welding Residual Stress ◽  
High Speed Train ◽  
Distribution Law ◽  
Element Analysis ◽  
Welding Sequence ◽  
Maximum Residual Stress

The finite element model of the roof of aluminum high-speed train was established, double ellipsoid heat source was employed, and heat elastic-plastic theory was used to simulate welding residual stress of the component under different welding sequence based on the finite element analysis software SYSWELD. The distribution law of welding residual stress was obtained. And the effects of the welding sequence on the value and distribution of residual stress was analyzed. The numerical results showed that the simulation data agree well with experimental test data. The maximum residual stress appears in the weld seam and nearby. The residual stress value decreases far away from the welding center. Welding sequence has a significant impact on the final welding residual stress when welding the roof of aluminum body. The side whose residual stress needs to be controlled should be welded first.

scholarly journals Finite element and biomechanical analysis of risk factors for implant failure during tension band plating

2020 ◽  
Vol 48 (11) ◽  
pp. 030006052097207
Author(s):  
Jing Ding ◽  
Fei Wang ◽  
Fangchun Jin ◽  
Zhen-kai Wu ◽  
Pin-quan Shen
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Biomechanical Model ◽  
Element Model ◽  
Tension Band ◽  
Biomechanical Analysis ◽  
Implant Failure ◽  
Element Analysis

Objective Tension band plating has recently gained widespread acceptance as a method of correcting angular limb deformities in skeletally immature patients. We examined the role of biomechanics in procedural failure and devised a new method of reducing the rate of implant failure. Methods In the biomechanical model, afterload (static or cyclic) was applied to each specimen. The residual stress of the screw combined with different screw sizes and configurations were measured and compared by X-ray diffraction. With regard to static load and similar conditions, the stress distribution was analyzed according to a three-dimensional finite element model. Results The residual stress was close to zero in the static tension group, whereas it was very high in the cyclic load group. The residual stress of screws was significantly lower in the convergent group and parallel group than in the divergent group. The finite element model showed similar results. Conclusions In both the finite element analysis and biomechanical tests, the maximum stress of the screw was concentrated at the position where the screws enter the cortex. Cyclic loading is the primary cause of implant failure.

Effect of Compressive and Shear Deformation of 2.5D Preform on its Stiffness of Composites

2019 ◽  
Vol 943 ◽  
pp. 75-80
Author(s):  
Fang Bin Lin ◽  
Ying Dai ◽  
Han Yang Li ◽  
Yang Qu ◽  
Wen Xiao Li
Keyword(s):  
Finite Element ◽  
Shear Deformation ◽  
Cell Model ◽  
Deformation Mode ◽  
Element Model ◽  
Tensile Tests ◽  
Woven Composites ◽  
Forming Process ◽  
Element Analysis ◽  
Plane Shear

Transverse compaction and in-plane shear deformartion are the dominative deformation mode for woven preform during forming process. A full finite element model of the 2.5D woven composites has been established by the computed tomography (CT) in this paper. Based on the energy method, the effective orthotropic/anisotropic stiffness coefficientsCijare calculated by performing a finite element analysis (FEA) of this full cell model. Using this model, the effects of the compaction and shear deformation of the 2.5D woven preform on the composites stiffness are investigated in detail. Compared the results of the static tensile tests, the rationality of the model and the method is verified.

scholarly journals Analysis and Control of Twist Defects of Aluminum Profiles with Large Z-Section in Roll Bending Process

Metals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 31 ◽  
Author(s):  
Anheng Wang ◽  
Hongqian Xue ◽  
Emin Bayraktar ◽  
Yanli Yang ◽  
Shah Saud ◽  
...  
Keyword(s):  
Finite Element ◽  
Aluminum Alloy ◽  
Element Model ◽  
Effective Control ◽  
Curvature Radius ◽  
3D Fem ◽  
Fe Method ◽  
Element Analysis ◽  
Roll Bending ◽  
Bending Process

This paper focuses on the twist defects and the control strategy in the process of four-roll bending for aluminum alloy Z-section profiles with large cross-section. A 3D finite element model (3D-FEM) of roll bending process has been developed, on the premise of the curvature radius of the profile, the particularly pronounced twist defects characteristic of 7075-O aluminum alloy Z-section profiles were studied by FE method. The simulation results showed that the effective control of the twist defects of the profile could be realized by adjusting the side roller so that the exit guide roll was higher than the entrance one (the side rolls presented an asymmetric loading mode with respect to the main rolls) and increasing the radius of upper roll. Corresponding experimental tests were carried out to verify the accuracy of the numerical analysis. The experimental results indicated that control strategies based on finite element analysis (FEA) had a significant inhibitory function on twist defects in the actual roll bending process.

Finite Element Analysis of Effects of Preheating and Postweld Heat Treatment on Residual Stress in Pipe Welding

2011 ◽  
Vol 314-316 ◽  
pp. 428-431 ◽  
Author(s):  
Hui Du ◽  
Dong Po Wang ◽  
Chun Xiu Liu ◽  
Hai Zhang
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Welding Process ◽  
Postweld Heat Treatment ◽  
Element Model ◽  
Element Analysis ◽  
Pipe Welding ◽  
Postweld Heat

To simulate preheating and postweld heat treatment of Q345 steel pipe welding, the finite element model was established. The welding process was simulated by method of the ANSYS element birth and death technique. In this paper, to obtain the distribution of the temperature field and stress field in different situations, preheating processes with two different values of temperature and postweld heat treatment process were simulated respectively. The results show that preheating can homogenize residual stress distribution of the weldment and decrease the residual stress. The heat treatment reduces the residual stress in inner and outer walls by 24% and 70% respectively and the stress distribution is more even and stress concentration is reduced.

Sheet Metals Forming Die Design Using Finite Element Analysis and the Taguchi Method

2014 ◽  
Vol 621 ◽  
pp. 195-201
Author(s):  
Surangsee Dechjarern ◽  
Maitri Kamonrattanapisut
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Friction Coefficient ◽  
Taguchi Method ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Element Model ◽  
Die Design ◽  
Forming Process ◽  
Element Analysis

Sheet metal deep-draw die is primarily constructed with draw bead, which is then modified based on trial and error to obtain a successful forming without splitting. This work aims at a robust design of forming die using numerical analysis and the Taguchi method. A three dimensional elastoplastic finite element model of a sheet metal forming process of SPCEN steel has been successfully developed using the material flow stress obtained from the modified Erichsen cup test. The model was validated with the actual forming experiment and the results agreed well. The influence of draw bead parameters on splitting and thinning distributions were examined using the Taguchi method. Four parameters, namely the friction coefficient, draw bead height, radius and shoulder radius were investigated. The Taguchi main effect analysis and ANOVA results show that the height and shoulder radius of the draw bead are the most important factor influencing the thinning distribution. Applying the Taguchi method and using the minimum thinning percentage as the design criteria, the optimum die design was identified as height, radius, shoulder radius and the friction coefficient of 4, 8, 8 mm and 0.125 respectively. The verified finite element model using the optimum die design was conducted. The predicted Taguchi response was within 5.9% from finite element analysis prediction. The improvement in the reduction of thinning percentage was 22.35%.

Sign in / Sign up

Export Citation Format

Share Document