Determination of Ascorbic Acid Based on a Platinum Nanoparticles Modified Au Electrode

2011 ◽  
Vol 110-116 ◽  
pp. 1732-1735
Author(s):  
Jia Hong He ◽  
Qiang Xu ◽  
Zhong Rong Song ◽  
Hai Yan Kuang
Keyword(s):  
Electron Microscopy ◽  
Ascorbic Acid ◽  
Modified Electrode ◽  
Platinum Nanoparticles ◽  
Reaction System ◽  
Au Electrode ◽  
Transmission Electron ◽  
Growth Method ◽  
One Step ◽  
The One

A Platinum nanoparticles modified Au electrode has been successfully fabricated by using an in situ growth method. In this method, the Platinum nanoparticles could be grown on the Au electrode surface via the one-step immersion into the mixture of H2PtCl6 (analytical grade, 1g/L), NaBH4 (analytical grade) and polyvinylpyrrolidone K30 (PVP, analytical grade). A certain amount of PVP was added into the reaction system to prevent the coagulation of the Platinum nanoparticles, which obtained by the chemical redox reaction of H2PtCl6 and NaBH4. The structures and morphologies of the Platinum nanoparticles were characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM) . The direct electrochemical behavior of ascorbic acid in 0.3 mol/L NaCl medium at the Platinum nanoparticles modified electrode has been investigated in detail. Compared to a bare Au electrode, a substantial decrease in the overvoltage of the ascorbic acid was observed at the Platinum nanoparticles modified electrode with oxidation starting at ca. 0.20 V vs. SCE (saturated KCl). At an applied potential of 0.18V, this modified electrode produced high and reproducible sensitivity to ascorbic acid and linear responses were obtained over a concentration range from 0.600 to 3.267 μmol/L with a detection limit of 1.9 nmol/L(S/N=3). The fabrication method of this sensor, which has highly sensitive, low working potential, and fast amperometric sensing to ascorbic acid, is simple and without using complex equipment. In addition, the sensor has been successfully used to detect ascorbic acid in real sample, thus is promising for the future development of ascorbic acid sensors.

Determination of Ascorbic Acid Based on a Platinum Nanoparticles Modified Au Electrode

2013 ◽  
Vol 562-565 ◽  
pp. 813-816
Author(s):  
Jia Hong He ◽  
Zhi Qiang Gao ◽  
Zhong Rong Song
Keyword(s):  
Electron Microscopy ◽  
Ascorbic Acid ◽  
Modified Electrode ◽  
Platinum Nanoparticles ◽  
Reaction System ◽  
Au Electrode ◽  
Transmission Electron ◽  
Growth Method ◽  
One Step ◽  
The One

A Platinum nanoparticles modified Au electrode has been successfully fabricated by using an in situ growth method. In this method, the Platinum nanoparticles could be grown on the Au electrode surface via the one-step immersion into the mixture of H2PtCl6 (analytical grade, 1g/L), NaBH4 (analytical grade) and polyvinylpyrrolidone K30 (PVP, analytical grade). A certain amount of PVP was added into the reaction system to prevent the coagulation of the Platinum nanoparticles, which obtained by the chemical redox reaction of H2PtCl6 and NaBH4. The structures and morphologies of the Platinum nanoparticles were characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM) . The direct electrochemical behavior of ascorbic acid in 0.3 mol/L NaCl medium at the Platinum nanoparticles modified electrode has been investigated in detail. Compared to a bare Au electrode, a substantial decrease in the overvoltage of the ascorbic acid was observed at the Platinum nanoparticles modified electrode with oxidation starting at ca. 0.20 V vs. SCE (saturated KCl). At an applied potential of 0.18V, this modified electrode produced high and reproducible sensitivity to ascorbic acid and linear responses were obtained over a concentration range from 0.600 to 3.267 μmol/L with a detection limit of 1.9 nmol/L(S/N=3). The fabrication method of this sensor, which has highly sensitive, low working potential, and fast amperometric sensing to ascorbic acid, is simple and without using complex equipment. In addition, the sensor has been successfully used to detect ascorbic acid in real sample, thus is promising for the future development of ascorbic acid sensors.

scholarly journals Ionic Liquids-Containing Silica Microcapsules: A Potential Tunable Platform for Shaping-Up Epoxy-Based Composite Materials?

Nanomaterials ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 881
Author(s):  
Ting Shi ◽  
Sébastien Livi ◽  
Jannick Duchet ◽  
Jean-François Gérard
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Diameter Distribution ◽  
Excellent Thermal Stability ◽  
Transmission Electron ◽  
Micron Size ◽  
Phosphonium Ionic Liquid ◽  
One Step ◽  
The One ◽  
First Time

In this work, silica microcapsules containing phosphonium ionic liquid (IL), denoted SiO2@IL, were successfully synthesized for the first time using the one step sol-gel method in IL/H20 emulsion. The morphologies of the obtained micron-size microcapsules, including their diameter distribution, were characterized using dynamic light scattering (DLS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The thermal behavior of these microcapsules and the mass fraction of the encapsulated IL in the silica microcapsules were determined using thermogravimetric analysis, showing an excellent thermal stability (up to 220 °C) and highlighting that an amount of 20 wt.% of IL is contained in the silica microcapsules. In a second step, SiO2@IL microcapsules (1 wt.%) were dispersed into epoxy-amine networks to provide proof of concept of the ability of such microcapsules to act as healing agents as microcracks propagate into the epoxy networks.

scholarly journals Tuning the Morphology of ZnO Nanostructures with the Ultrasonic Spray Pyrolysis Process

Metals ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 569 ◽  
Author(s):  
Elif Emil ◽  
Gözde Alkan ◽  
Sebahattin Gurmen ◽  
Rebeka Rudolf ◽  
Darja Jenko ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Spray Pyrolysis ◽  
Ultrasonic Spray Pyrolysis ◽  
Ultrasonic Spray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Zno Particles ◽  
One Step ◽  
Spray Pyrolysis Process ◽  
The One

Nanostructured zinc oxide (ZnO) particles were synthesized by the one step Ultrasonic Spray Pyrolysis (USP) process from nitrate salt solution (Zn(NO3)2·6H2O). Various influential parameters, from Zn(NO3)2·6H2O concentrations (0.01875–0.0375 M) in the initial solution, carrier gas (N2) flow rates (0.5–0.75 L/min) to reaction temperature (400–800 °C), were tested to investigate their role on the final ZnO particles’ morphology. For this purpose, Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HRTEM) and (Selected Area Electron Diffraction) SAED techniques were used to gain insight into how the ZnO morphology is dependent on the USP process. It was revealed that, by certain parameter selection, different ZnO morphology could be achieved, from spherical to sphere-like structures assembled by interwoven nanoplate and nanoplate ZnO particles. Further, a more detailed crystallographic investigation was performed by XRD and Williamson-Hall (W-H) analysis on the ZnO with unique and non-typical planar morphology that was not reported before by USP synthesis. Moreover, for the first time, a flexible USP formation model was proposed, ending up in various ZnO morphologies rather than only ideal spheres, which is highly promising to target a wide application area.

The Preparation of Platinum Nanoparticles on Titanium Using Chemical Reductive Growth Procedures

2012 ◽  
Vol 490-495 ◽  
pp. 3811-3815
Author(s):  
Li Guo ◽  
Jian Qiang Hu ◽  
Hu Zhang ◽  
Shi Zhao Yang
Keyword(s):  
Ascorbic Acid ◽  
Electron Microscope ◽  
Platinum Nanoparticles ◽  
Pt Nanoparticles ◽  
Resolution Electron ◽  
One Step ◽  
New Type ◽  
High Resolution Electron Microscope ◽  
The One ◽  
Fcc Structure

The synthesis of platinum nanoparticles by reduction of H2PtCl6 with ascorbic acid has been studied. By high-resolution electron microscope and XRD analyses, the resultant nanoparticles have been found to be pure platinum of fcc structure. Their sizes were observed to increase with the increases chemical reductive with 24h. Then, platinum nanoparticles directly attached to Ti plates(Pt nanoparticles/Ti) were successfully fabricated. In this method, platinum nanoparticles could be grown on the Ti surface via the one-step immersion into the growth solution containing PtCl62- and ascorbic acid. The attached and grown platinum nanoparticles were spherical having an agglomerated nanostructure composed of small nanoclusters. The present Pt nanoparticles/Ti may be promising for a new type of electrode material.

scholarly journals Effects of Aging on the Microstructure and Properties of 7075 Al Sheets

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4022
Author(s):  
Zhongxin Zhao ◽  
Ruoqing Wu ◽  
Bo Wang ◽  
Mingchu Huang ◽  
Guopeng Lei ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Treatment Time ◽  
Aging Treatment ◽  
Strength Properties ◽  
Double Aging ◽  
Transmission Electron ◽  
One Step ◽  
The One ◽  
Effects Of Aging ◽  
Working Efficiency

The effects of one-step aging and double aging on the properties and microstructures of 7075 Al sheets were studied via mechanical property testing, scanning electron microscopy, and transmission electron microscopy. The results indicated that with continued one-step aging, the tensile and yield strengths of the Al sheets first increased rapidly with an increase in the treatment time to 8 h and then increased slightly with a further increase in the treatment time to 10 h. The tensile and yield strengths became constant after 16 h of treatment. The mechanical strength properties of the Al sheets peaked after 16 h of one-step aging. However, the double aging treatment provided better mechanical properties and working efficiency than the one-step aging treatment. The tensile strength and microhardness resulting from double aging were greater than those resulting from one-step aging by 5.87% and 8.71%, respectively. Herein, we quantified the contribution ofvarious strengthening mechanisms.

Encapsulation of Luminescent Quantum Nanodots in Polystyrene Nanocapsules by Microemulsion Polymerization

2005 ◽  
Vol 23 ◽  
pp. 19-22 ◽  
Author(s):  
Xiaotun Yang ◽  
Ning Huang ◽  
Yong Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Quantum Dots ◽  
Fluorescence Microscopy ◽  
Fluorescence Spectroscopy ◽  
Microemulsion Polymerization ◽  
Transmission Electron ◽  
One Step ◽  
The One ◽  
Polymerization Method

This paper reported on the one-step synthesis of polystyrene-quantum dots (PS@QD)nanoparticles using microemulsion polymerization method. The synthesized QD and PS@QD nanoparticles were characterized by UV, fluorescence spectroscopy, transmission electron microscopy (TEM) and fluorescence microscopy. The PS@QD is highly luminescent, which have the potential to be used as fluorescent probes in biological staining and diagnostics.

Nucleation of Disorder in Fe3Al Alloys

1967 ◽  
Vol 25 ◽  
pp. 312-313
Author(s):  
P. R. Swann ◽  
W. R. Duff ◽  
R. M. Fisher
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Annealing Temperature ◽  
Antiphase Domain ◽  
Effect Of Temperature ◽  
Domain Structures ◽  
Transmission Electron ◽  
Domain Boundaries ◽  
Higher Temperature ◽  
The One

Recently we have investigated the phase equilibria and antiphase domain structures of Fe-Al alloys containing from 18 to 50 at.% Al by transmission electron microscopy and Mössbauer techniques. This study has revealed that none of the published phase diagrams are correct, although the one proposed by Rimlinger agrees most closely with our results to be published separately. In this paper observations by transmission electron microscopy relating to the nucleation of disorder in Fe-24% Al will be described. Figure 1 shows the structure after heating this alloy to 776.6°C and quenching. The white areas are B2 micro-domains corresponding to regions of disorder which form at the annealing temperature and re-order during the quench. By examining specimens heated in a temperature gradient of 2°C/cm it is possible to determine the effect of temperature on the disordering reaction very precisely. It was found that disorder begins at existing antiphase domain boundaries but that at a slightly higher temperature (1°C) it also occurs by homogeneous nucleation within the domains. A small (∼ .01°C) further increase in temperature caused these micro-domains to completely fill the specimen.

scholarly journals Photocatalytic Degradation of Tetracycline in Aqueous Solution Using Copper Sulfide Nanoparticles

Catalysts ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1238
Author(s):  
Murendeni P. Ravele ◽  
Opeyemi A. Oyewo ◽  
Sam Ramaila ◽  
Lydia Mavuru ◽  
Damian C. Onwudiwe
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Copper Sulfide ◽  
Degradation Rate ◽  
Light Exposure ◽  
Reaction System ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Pure Phase

In this paper, spherical-shaped pure phase djurleite (Cu31S16) and roxbyite (Cu7S4) nanoparticles were prepared by a solvothermal decomposition of copper(II) dithiocarbamate complex in dodecanthiol (DDT). The reaction temperature was used to control the phases of the samples, which were represented as Cu31S16 (120 °C), Cu31S16 (150 °C), Cu7S4 (220 °C), and Cu7S4 (250 °C) and were characterized by using X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM), and absorption spectroscopy. The samples were used as photocatalysts for the degradation of tetracycline (TC) under visible light irradiation. The results of the study showed that Cu7S4 (250 °C) exhibited the best activity in the reaction system with the TC degradation rate of up to 99% within 120 min of light exposure, while the Cu31S16 (120 °C) system was only 46.5% at the same reaction condition. In general, roxbyite Cu7S4 (250 °C) could be considered as a potential catalyst for the degradation of TC in solution.

Conversion of platelets into dislocation loops and voidite formation in type IaB diamonds

1995 ◽  
Vol 449 (1936) ◽  
pp. 295-313 ◽  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Local Mode ◽  
Diamond Structure ◽  
Dislocation Loops ◽  
X Ray ◽  
Regular Type ◽  
Transmission Electron ◽  
Stable Conditions ◽  
The One

Type la natural diamonds have been heated in the temperature range of 2400-2700°C under stabilizing pressures. The specimens studied are mainly regular type IaB diamonds. Transmission electron microscopy studies of treated speci­mens show that platelets are converted to interstitial ½ a 0 <011> dislocation loops; voidites are also formed. When all the platelets have been converted, the ex­perimental features associated with them also disappear, i. e. the X-ray extra reflections (spikes), the B' local-mode absorption and the lattice absorption in the one-phonon region termed the D spectrum. It is discovered that when diamonds are heated under graphite-stable rather than diamond-stable conditions, the rate of conversion is considerably enhanced; for instance, at 2650°C there is an increase in the rate of about three orders of magnitude. This enhancement is considered to be due to the instability of the diamond structure itself and a reason for this enhancement is suggested.

scholarly journals A facile synthesis of a carbon-encapsulated Fe3O4 nanocomposite and its performance as anode in lithium-ion batteries

2013 ◽  
Vol 4 ◽  
pp. 699-704 ◽  
Author(s):  
Raju Prakash ◽  
Katharina Fanselau ◽  
Shuhua Ren ◽  
Tapan Kumar Mandal ◽  
Christian Kübel ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Lithium Ion ◽  
Iron Pentacarbonyl ◽  
X Ray Diffraction ◽  
Facile Synthesis ◽  
X Ray ◽  
Transmission Electron ◽  
Lithium Ion Cell ◽  
Carbon Framework ◽  
One Step

A carbon-encapsulated Fe3O4 nanocomposite was prepared by a simple one-step pyrolysis of iron pentacarbonyl without using any templates, solvents or surfactants. The structure and morphology of the nanocomposite was investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer–Emmett–Teller analysis and Raman spectroscopy. Fe3O4 nanoparticles are dispersed intimately in a carbon framework. The nanocomposite exhibits well constructed core–shell and nanotube structures, with Fe3O4 cores and graphitic shells/tubes. The as-synthesized material could be used directly as anode in a lithium-ion cell and demonstrated a stable capacity, and good cyclic and rate performances.

Sign in / Sign up

Export Citation Format

Share Document