Numerical Simulation of Inner Support for Excavation Based on FEM Software ABAQUS

2012 ◽  
Vol 236-237 ◽  
pp. 632-635
Author(s):  
Yue Sun ◽  
Yue Nan Chen ◽  
Zhi Yun Wang
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Computational Model ◽  
Dimensional Space ◽  
General Purpose ◽  
Two Dimensional ◽  
Clay Layer ◽  
Finite Element Software ◽  
Spring Element

In two-dimensional space, an elasto-plastic finite element computational model was established to simulate inner support for excavation on the basis of the general-purpose finite element software ABAQUS. The soil was assumed to be a uniform and normally consolidated clay layer and strut was discreted by spring element. Compared with published case study, it can be concluded that FEM software AQAQUS can present one reliable simulation progress of inner support for excavation.

Numerical Analysis of Passive Pile due to Excavation

2012 ◽  
Vol 594-597 ◽  
pp. 198-201
Author(s):  
Yue Sun ◽  
Zhi Yun Wang ◽  
Yue Nan Chen ◽  
Yun Shen Jiang
Keyword(s):  
Finite Element ◽  
Shear Strength ◽  
Dimensional Space ◽  
Undrained Shear Strength ◽  
General Purpose ◽  
Soil Movement ◽  
Finite Element Software ◽  
Passive Pile ◽  
Pile Response ◽  
Undrained Shear

An elasto-plastic total stress finite-element computational model is established in two dimensional space to study pile response due to excavation-induced soil movement on the basis of the general-purpose finite element software ABAQUS. And the soil is assumed to be a uniform normally consolidated clay layer. Influences of various parameters including undrained shear strength of soil, excavation depth, strut stiffness and distance from excavation on pile response are investigated. The results indicate that the excavation-induced soil movement is critical for adjacent piles and increasing the undrained shear strength of soil and distance from excavation face would be helpful to control passive pile responses.

Optimal Design of the Large-Diameter Spinning Torispherical Head

2012 ◽  
Vol 544 ◽  
pp. 194-199
Author(s):  
Di Zhang ◽  
Shui Ping Sheng ◽  
Zeng Liang Gao
Keyword(s):  
Finite Element ◽  
Optimal Design ◽  
Large Diameter ◽  
General Purpose ◽  
Design Tool ◽  
Crown Area ◽  
Finite Element Software ◽  
The Stability

Two important parameters of torispherical head that are (interior radius of spherical crown area) and r (interior radius of transition corner) have been optimized by the module of the large general-purpose finite-element software ANSYS, targeting the strength and stability of the head. This paper provides an optimized torispherical head, which improves the stability of the edge of the head with acceptable strength of the head. The procedure is generally applicable as a design tool for optimal design.

Implementation of p and h-p Versions of the Finite Element Method

1992 ◽  
Author(s):  
Ye-Chen Lai ◽  
Timothy C. S. Liang ◽  
Zhenxue Jia
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Elastic Analysis ◽  
Two Dimensional ◽  
The Finite Element Method ◽  
Shape Functions ◽  
Linear Elastic ◽  
Finite Element Software ◽  
Analysis Process ◽  
Adaptive Analysis

Abstract Based on hierarchic shape functions and an effective convergence procedure, the p-version and h-p adaptive analysis capabilities were incorporated into a finite element software system, called COSMOS/M. The range of the polynomial orders can be varied from 1 to 10 for two dimensional linear elastic analysis. In the h-p adaptive analysis process, a refined mesh are first achieved via adaptive h-refinement. The p-refinement is then added on to the h-version designed mesh by uniformly increasing the degree of the polynomials. Some numerical results computed by COSMOS/M are presented to illustrate the performance of these p and h-p analysis capabilities.

scholarly journals Numerical simulation of blanking process

2018 ◽  
Vol 157 ◽  
pp. 02038
Author(s):  
Peter Pecháč ◽  
Milan Sága
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Steel Sheet ◽  
Plastic Material ◽  
Material Model ◽  
Rolled Steel ◽  
Finite Element Software ◽  
History Of ◽  
Cold Rolled ◽  
Blanking Process

This paper presents numerical simulation of blanking process for cold-rolled steel sheet metal. The problem was modeled using axial symmetry in commercial finite element software ADINA. Data obtained by experimental measurement were used to create multi-linear plastic material model for simulation. History of blanking force vs. tool displacement was obtained.

scholarly journals Development Trend and Stability Analysis of Creep Landslide With Obvious Slip Zone Under Rainfall-Taking Xinchang Xiashan Basalt Slope as an Example

2022 ◽  
Vol 9 ◽  
Author(s):  
Chunyan Bao ◽  
Lingtao Zhan ◽  
Yingjie Xia ◽  
Yongliang Huang ◽  
Zhenxing Zhao
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Stability Analysis ◽  
Soil Layer ◽  
Heavy Rain ◽  
Development Trend ◽  
Sliding Surface ◽  
Landslide Area ◽  
Finite Element Software ◽  
Sliding Zone

The creep slope is a dynamic development process, from stable deformation to instability failure. For the slope with sliding zone, it generally creeps along the sliding zone. If the sliding zone controlling the slope sliding does not have obvious displacement, and the slope has unexpected instability without warning, the harm and potential safety hazard are often much greater than the visible creep. Studying the development trend of this kind of landslide is of great significance to slope treatment and landslide early warning. Taking Xiashan village landslide in Huishan Town, Xinchang County, Zhejiang Province as an example, the landslide point was determined by numerical simulation in 2006. Generally, the landslide is a typical long-term slow deformation towards the free direction. Based on a new round of investigation and monitoring, this paper shows that there are signs of creeping on the surface of the landslide since 2003, and there is no creep on the deep sliding surface. The joint fissures in the landslide area are relatively developed, and rainfall infiltration will soften the soft rock and soil layer and greatly reduce its stability. This paper collects and arranges the rainfall data of the landslide area in recent 30 years, constructs the slope finite element model considering rainfall conditions through ANSYS finite element software, and carries out numerical simulation stability analysis. The results show that if cracks appear below or above the slope’s sliding surface, or are artificially damaged, the sliding surface may develop into weak cracks. Then, the plastic zone of penetration is offset; In the case of heavy rain, the slope can unload itself under the action of rainfall. At this time, the slope was unstable and the landslide happened suddenly.

scholarly journals Verification of the flexion and shear behavior in masonry panels accordance to ABNT NBR 15961-1 (2011), EN 1996-1-1 (2005) and ACI TMS 530 (2013)

2018 ◽  
Vol 11 (4) ◽  
pp. 673-685
Author(s):  
R. C. MATA ◽  
C. S. RAMOS ◽  
M. L. C. SILVA
Keyword(s):  
Computer Simulation ◽  
Finite Element ◽  
Numerical Model ◽  
Design Criteria ◽  
Two Dimensional ◽  
Finite Element Software ◽  
Modelling Procedure ◽  
Increasing Trend ◽  
American Standard ◽  
Compression Level

Abstract This paper presents a numerical analysis of the mechanical behavior of structural masonry panels submitted to horizontal and vertical stresses. To evaluate the design process of these structures, the results obtained by the computer simulations were compared with the results determined by the design criteria of ABNT NBR 15961-1 (2011), ACI TMS 530 (2013) and EN 1996-1-1 (2005). The finite element software DIANA v.9.3 was used to simulate two-dimensional models with the simplified micro modelling procedure. The results obtained by the normative standards were more conservative than the results of the numerical model, as expected. With the increase of the pre-compression level, the computer simulation has demonstrated the increasing trend of the values of resistant forces, besides the change of the way of rupture of the panels. Among the three standards evaluated, the American Standard was the most conservative.

Numerical Simulation of the Kinetic Energy Projectile Oblique Penetration into the Concrete

2014 ◽  
Vol 989-994 ◽  
pp. 982-985
Author(s):  
Jun Chen ◽  
Xiao Jun Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Test Results ◽  
Destruction Process ◽  
3D Finite Element ◽  
Finite Element Software ◽  
Simulation Results ◽  
Target Characteristics

ANSYS-LS/DYNA 3D finite element software projectile penetrating concrete target three-dimensional numerical simulation , has been the target characteristics and destroy ballistic missile trajectory , velocity and acceleration and analyze penetration and the time between relationship , compared with the test results , the phenomenon is consistent with the simulation results. The results show that : the destruction process finite element software can better demonstrate concrete tests revealed the phenomenon can not be observed , estimated penetration depth and direction of the oblique penetration missile deflection .

scholarly journals Numerical Simulation of Transient Electromagnetic Response of Unfavorable Geological Body in Tunnel

2011 ◽  
Vol 90-93 ◽  
pp. 37-40 ◽  
Author(s):  
Lu Bo Meng ◽  
Tian Bin Li ◽  
Zheng Duan
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Electromagnetic Field ◽  
Electromagnetic Response ◽  
Detection Distance ◽  
Geological Body ◽  
Response Characteristics ◽  
Finite Element Software ◽  
Transient Electromagnetic ◽  
Field Decay

To investigate the transient electromagnetic method of response characteristics in the tunnel geological prediction, the finite element numerical simulation of unfavorable geological body of different location, different resistivity sizes, different shapes, and different volume size were carried out by ANSYS finite element software. The results show that secondary electromagnetic field of different location of unfavorable geological body have same decay rate, when detection distance from 30m to 70m, transient electromagnetic responses are strongest, followed distance from 10m to 30m and from 70m to 90m. The shape, volume and resistivity of unfavorable geological body have strong influence on transient electromagnetic response, unfavorable geological body more sleek, the greater the volume and the smaller the resistivity of unfavorable geological body, the secondary electromagnetic field decay slower.

Sign in / Sign up

Export Citation Format

Share Document