scholarly journals Development Trend and Stability Analysis of Creep Landslide With Obvious Slip Zone Under Rainfall-Taking Xinchang Xiashan Basalt Slope as an Example

2022 ◽  
Vol 9 ◽  
Author(s):  
Chunyan Bao ◽  
Lingtao Zhan ◽  
Yingjie Xia ◽  
Yongliang Huang ◽  
Zhenxing Zhao
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Stability Analysis ◽  
Soil Layer ◽  
Heavy Rain ◽  
Development Trend ◽  
Sliding Surface ◽  
Landslide Area ◽  
Finite Element Software ◽  
Sliding Zone

The creep slope is a dynamic development process, from stable deformation to instability failure. For the slope with sliding zone, it generally creeps along the sliding zone. If the sliding zone controlling the slope sliding does not have obvious displacement, and the slope has unexpected instability without warning, the harm and potential safety hazard are often much greater than the visible creep. Studying the development trend of this kind of landslide is of great significance to slope treatment and landslide early warning. Taking Xiashan village landslide in Huishan Town, Xinchang County, Zhejiang Province as an example, the landslide point was determined by numerical simulation in 2006. Generally, the landslide is a typical long-term slow deformation towards the free direction. Based on a new round of investigation and monitoring, this paper shows that there are signs of creeping on the surface of the landslide since 2003, and there is no creep on the deep sliding surface. The joint fissures in the landslide area are relatively developed, and rainfall infiltration will soften the soft rock and soil layer and greatly reduce its stability. This paper collects and arranges the rainfall data of the landslide area in recent 30 years, constructs the slope finite element model considering rainfall conditions through ANSYS finite element software, and carries out numerical simulation stability analysis. The results show that if cracks appear below or above the slope’s sliding surface, or are artificially damaged, the sliding surface may develop into weak cracks. Then, the plastic zone of penetration is offset; In the case of heavy rain, the slope can unload itself under the action of rainfall. At this time, the slope was unstable and the landslide happened suddenly.

scholarly journals Numerical simulation of blanking process

2018 ◽  
Vol 157 ◽  
pp. 02038
Author(s):  
Peter Pecháč ◽  
Milan Sága
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Steel Sheet ◽  
Plastic Material ◽  
Material Model ◽  
Rolled Steel ◽  
Finite Element Software ◽  
History Of ◽  
Cold Rolled ◽  
Blanking Process

This paper presents numerical simulation of blanking process for cold-rolled steel sheet metal. The problem was modeled using axial symmetry in commercial finite element software ADINA. Data obtained by experimental measurement were used to create multi-linear plastic material model for simulation. History of blanking force vs. tool displacement was obtained.

Numerical Simulation of Inner Support for Excavation Based on FEM Software ABAQUS

2012 ◽  
Vol 236-237 ◽  
pp. 632-635
Author(s):  
Yue Sun ◽  
Yue Nan Chen ◽  
Zhi Yun Wang
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Computational Model ◽  
Dimensional Space ◽  
General Purpose ◽  
Two Dimensional ◽  
Clay Layer ◽  
Finite Element Software ◽  
Spring Element

In two-dimensional space, an elasto-plastic finite element computational model was established to simulate inner support for excavation on the basis of the general-purpose finite element software ABAQUS. The soil was assumed to be a uniform and normally consolidated clay layer and strut was discreted by spring element. Compared with published case study, it can be concluded that FEM software AQAQUS can present one reliable simulation progress of inner support for excavation.

Numerical Simulation of the Kinetic Energy Projectile Oblique Penetration into the Concrete

2014 ◽  
Vol 989-994 ◽  
pp. 982-985
Author(s):  
Jun Chen ◽  
Xiao Jun Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Test Results ◽  
Destruction Process ◽  
3D Finite Element ◽  
Finite Element Software ◽  
Simulation Results ◽  
Target Characteristics

ANSYS-LS/DYNA 3D finite element software projectile penetrating concrete target three-dimensional numerical simulation , has been the target characteristics and destroy ballistic missile trajectory , velocity and acceleration and analyze penetration and the time between relationship , compared with the test results , the phenomenon is consistent with the simulation results. The results show that : the destruction process finite element software can better demonstrate concrete tests revealed the phenomenon can not be observed , estimated penetration depth and direction of the oblique penetration missile deflection .

scholarly journals Numerical Simulation of Transient Electromagnetic Response of Unfavorable Geological Body in Tunnel

2011 ◽  
Vol 90-93 ◽  
pp. 37-40 ◽  
Author(s):  
Lu Bo Meng ◽  
Tian Bin Li ◽  
Zheng Duan
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Electromagnetic Field ◽  
Electromagnetic Response ◽  
Detection Distance ◽  
Geological Body ◽  
Response Characteristics ◽  
Finite Element Software ◽  
Transient Electromagnetic ◽  
Field Decay

To investigate the transient electromagnetic method of response characteristics in the tunnel geological prediction, the finite element numerical simulation of unfavorable geological body of different location, different resistivity sizes, different shapes, and different volume size were carried out by ANSYS finite element software. The results show that secondary electromagnetic field of different location of unfavorable geological body have same decay rate, when detection distance from 30m to 70m, transient electromagnetic responses are strongest, followed distance from 10m to 30m and from 70m to 90m. The shape, volume and resistivity of unfavorable geological body have strong influence on transient electromagnetic response, unfavorable geological body more sleek, the greater the volume and the smaller the resistivity of unfavorable geological body, the secondary electromagnetic field decay slower.

The Studies on Numerical Simulation of Unidirectional Solidification Process in 23t Steel Ingot

2012 ◽  
Vol 502 ◽  
pp. 46-50
Author(s):  
Guang Wu Ao ◽  
Ming Gang Shen ◽  
Zhen Shan Zhang ◽  
Li Li Hong
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Temperature Distribution ◽  
Steel Ingot ◽  
Side Wall ◽  
Solidification Process ◽  
Unidirectional Solidification ◽  
Finite Element Software ◽  
Solidification Processes

In this paper, by using the commercial finite-element software of ProCAST, unidirectional solidification processes in 23t steel ingot were simulated. Emphasis is placed on analysis of required time for complete solidification of steel ingot and temperature distribution about ingot and side wall during the solidification process. By comparing simulation values and measured values of side wall during the solidification process, the simulated results conclusively demonstrate that our developed model is feasible and valuable.

Integrity Assessment of Subsea Pipeline Dent / Buckle Using ILI Data

2019 ◽  
Author(s):  
Gurumurthy Kagita ◽  
Gudimella G. S. Achary ◽  
Mahesh B. Addala ◽  
Balaji Srinivasan ◽  
Penchala S. K. Pottem ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Failure Modes ◽  
Structural Integrity ◽  
Mechanical Damage ◽  
Metal Loss ◽  
Stress Concentrations ◽  
Subsea Pipeline ◽  
Integrity Assessment ◽  
Finite Element Software

Abstract Mechanical damage in subsea pipelines in the form of local dents / buckles due to excessive bending deformation may severely threaten their structural integrity. A dent / buckle has two significant effects on the pipeline integrity. Notably, residual stresses are set up as result of the plastic deformation and stress concentrations are created due to change in pipe geometry caused by the denting / buckling process. To assess the criticality of a dent / buckle, which often can be associated with strain induced flaws in the highly deformed metal, integrity assessment is required. The objective of this paper is to evaluate the severity of dent / buckle in a 48” subsea pipeline and to make the rerate, repair or replacement decision. This paper presents a Level 3 integrity assessment of a subsea pipeline dent / buckle with metal loss, reported in in-line inspection (ILI), in accordance with Fitness-For-Service Standard API 579-1/ASME FFS-1. In this paper, the deformation process that caused the damage (i.e. dent / buckle) with metal loss is numerically simulated using ILI data in order to determine the magnitude of permanent plastic strain developed and to evaluate the protection against potential failure modes. For numerical simulation, elastic-plastic finite element analyses (FEA) are performed considering the material as well as geometric non-linearity using general purpose finite element software ABAQUS/CAE 2017. Based on the numerical simulation results, the integrity assessment of dented / buckled subsea pipeline segment with metal loss has been performed to assess the fitness-for-service at the operating loads.

MECHANICAL SIMULATION AND ELECTROCHEMICAL CORROSION IN A BURIED PIPELINE WITH CORROSION DEFECTS SITUATED IN PERMAFROST REGIONS

2020 ◽  
pp. 2150002
Author(s):  
XIAOLI LI ◽  
LI CHEN ◽  
XIAOYAN LIU ◽  
YU ZHANG ◽  
LIFU CUI
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Simulation Analysis ◽  
Electrochemical Corrosion ◽  
Frost Heave ◽  
Buried Pipeline ◽  
Mechanical Coupling ◽  
Finite Element Software ◽  
Corrosion Defects ◽  
Permafrost Regions

The geological environment along a buried pipeline in permafrost regions is complex, where differential frost heave often occurs. To understand the changes in the stress behavior of pipeline structures caused by corrosion while laying them in permafrost regions, we established a thermo-mechanical coupling model of buried pipeline with corrosion defects by using finite element software. Numerical simulation analysis of buried pipeline was conducted. The effects of the frost heave length, the length of the transition section, the corrosion depth, and the corrosion length on the stress displacement were obtained. These analyses showed that the stresses and displacements of the pipeline with corrosion defects in permafrost regions can be simulated by using the finite element software numerical simulation method. Afterward, the corrosion resistances of pipelines with different corrosion lengths and depths were investigated via an electrochemical testing method. These results can provide some useful insights into the possible mechanical state of buried pipeline with regard to their design and construction, as well as some useful theoretical references for simulating real-time monitoring and safety analysis for their operation in permafrost regions.

Numerical Simulation on Supporting of Deep Surrounding Rock with Zonal Disintegration Tendency

2013 ◽  
Vol 671-674 ◽  
pp. 230-234
Author(s):  
Yu Jun Zuo ◽  
De Kang Zhu ◽  
Wan Cheng Zhu
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Surrounding Rock ◽  
Zonal Disintegration ◽  
Finite Element Software ◽  
Stability Of Surrounding Rock ◽  
Ground Stress ◽  
Zonal Disintegration Phenomenon ◽  
The Stability ◽  
The Zonal Disintegration Phenomenon

In order to study the supporting of deep surrounding rock with zonal disintegration tendency, the zonal disintegration phenomenon of deep surrounding rock under three supporting forms is analyzed by the ABAQUS finite element software in this paper, and three supporting forms are un-supporting, bolting and grouting, and combined “Bolting and grouting plus Anchor rope” supporting. The results show that the different effects to zonal disintegration under different supporting forms will occur. Supporting can help to restrain the zonal disintegration of the reinforcement part advantageously, and also lower rupture degree of zonal disintegration and reduce the size of rupture zone. Meanwhile, the stability of surrounding rock is improved. But zonal disintegration may occur outside reinforcement part under greater ground stress. The results are great importance to a better understanding of the deep roadway supporting.

scholarly journals Experimental Study and Theoretical Analysis on Flexural Mechanical Propertiesof Reinforced Timber Beams

2018 ◽  
Vol 27 (1) ◽  
pp. 096369351802700
Author(s):  
Xiong Xueyu ◽  
Wang Yiqingzi ◽  
Xue Rongjun ◽  
Lu Xuanxing
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Theoretical Calculations ◽  
Development Trend ◽  
Ultimate Bearing Capacity ◽  
Bending Test ◽  
Element Analysis ◽  
Finite Element Software ◽  
Reinforced Beams

As Chinese architecture masterpiece, ancient Hui-style architecture is the admiration for Chinese and foreign master builders. According to the bending test, the theoretical calculations and Abaqus finite element analysis on 5 Hui-style architecture beams, this paper points out the differences between un-reinforced beams and reinforced beams on ultimate bearing capacity, deflection and other performance indicators. The reinforcement methods of embedding steel bars, embedding CFRP bars and pasting CFRP plate can respectively improve the ultimate bearing capacity by 20.2%, 32.6% and 37.0%. Based on the plane section assumption and considering thereduction of tensile strength causedby wood knots and defects in tension zone, this paper predicts failure modes of the test beams may occur, and gives the ultimate bearing capacity of different failure modes. In addition, this paper uses the Abaqus finite element software for simulating test beams, and the development trend of load-deflectioncurve between the test and numerical simulation are in good agreement, providing reference for further research of Hui-style architecture.

scholarly journals Numerical simulation of electrohydraulic processes

2018 ◽  
Vol 245 ◽  
pp. 09015 ◽  
Author(s):  
Viatcheslav S. Mamutov ◽  
Alexander V. Mamutov
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Energy Deposition ◽  
Discharge Chamber ◽  
Plasma Channel ◽  
Analytical Calculation ◽  
Experimental Results ◽  
Software Complex ◽  
Finite Element Software ◽  
Channel Water

Using the finite element software complex LS-DYNA 971, the technique of simulating processes of Electro-Hydraulic forming is developed. The law of energy deposition is obtained from semi-analytical calculation. A simulation of complex EHF process, which includes discharge chamber with electrodes, plasma channel, water, deformable blank that is formed into a rigid die, is performed using the developed technique. The simulation is validated by experimental results. The developed technique significantly extends practical usage of numerical simulation of electrohydraulic forming and other electrohydraulic-based technologies.

Sign in / Sign up

Export Citation Format

Share Document