Influence of Large Water Droplets Passing through Microwave Cavity on Steam Wetness Measurement

2013 ◽  
Vol 339 ◽  
pp. 495-502
Author(s):  
Jiang Bo Qian ◽  
Heng Fan Li ◽  
Zhong He Han
Keyword(s):  
Resonant Frequency ◽  
Quality Factor ◽  
Resonant Cavity ◽  
Great Influence ◽  
Microwave Cavity ◽  
Large Droplet ◽  
Ring Radius ◽  
Secondary Droplets ◽  
Large Water ◽  
Turbine Exhaust

The steam turbine exhaust contains large secondary droplets, and the droplets show an uneven distribution in space and time. It analyzes the change of resonant frequency and quality factor with different sizes and positions of droplets, and analyzes the influence on the steam wetness measurement. The results show that: when the size of resonant cavity is constant, the resonant frequency and quality factor are related to the size and location of water droplet. For the cylindrical cavity whose length is 40mm and radius is 30mm, when large droplet located in the ring (radius is 13.0mm) onxoyplane, it has great influence on wetness measurement, and the influence is greater with larger size of droplet.

scholarly journals Catalyst State Diagnosis of Three-Way Catalytic Converters Using Different Resonance Parameters—A Microwave Cavity Perturbation Study

Sensors ◽  
2019 ◽  
Vol 19 (16) ◽  
pp. 3559
Author(s):  
Carsten Steiner ◽  
Vladimir Malashchuk ◽  
David Kubinski ◽  
Gunter Hagen ◽  
Ralf Moos
Keyword(s):  
Resonant Frequency ◽  
Quality Factor ◽  
Signal Amplitude ◽  
Oxygen Storage ◽  
Microwave Cavity ◽  
Technical Application ◽  
Gasoline Vehicles ◽  
Relative Change ◽  
Rf Signal ◽  
First Time

Recently, radio frequency (RF) technology was introduced as a tool to determine the oxygen storage level of a three-way catalyst (TWC) for gasoline vehicles. Previous studies on the investigation of commercial catalysts mostly use only the resonant frequency to describe the correlation of oxygen storage level and RF signal. For the first time this study presents a comparison under defined laboratory conditions considering both, resonance frequency and also the quality factor as measurands. Furthermore, various advantages over the sole use of the resonant frequency in the technical application are discussed. Experiments with Ø4.66’’ catalysts and Ø1.66’’ catalyst cores with alternating (rich/lean) gas compositions showed that the relative change in signal amplitude due to a change in oxygen storage is about 100 times higher for the inverse quality factor compared to the resonant frequency. In addition, the quality factor reacts more sensitively to the onset of the oxygen-storage ability, and delivers precise information about the necessary temperature, which is not possible when evaluating the resonant frequency due to the low signal amplitude. As investigations on aged catalysts confirm, the quality factor also provides a new approach to determine operando the ageing state of a TWC.

The Uncertainty Analysis of Microwave Resonant Cavity System for Wetness Measurement

2014 ◽  
Vol 643 ◽  
pp. 176-182
Author(s):  
Jun Ke Zhang ◽  
Tin Ge ◽  
Jing Yu Liu ◽  
Ming Li ◽  
Xiao Zhe Yan
Keyword(s):  
Sampling Error ◽  
Resonant Cavity ◽  
Water Film ◽  
Steam Pressure ◽  
Frequency Measurement ◽  
Standard Uncertainty ◽  
Microwave Cavity ◽  
System Uncertainty ◽  
Cavity System ◽  
Parameters Measurement

Steam pressure and resonant frequency of microwave cavity are important measure parameters of microwave wetness measurement system. The measuring precision of pressure and frequency directly affect the accuracy of wetness measurement. This paper takes different pressure and wetness of steam as example to analyze the parameter uncertainty of measurement relationship and deduces standard uncertainty of wetness measurement. The system comprehensive uncertainty is identified, when the parameters measurement, cavity heat expansion, sampling error, sedimentary water film and so on are considered. The result shows that the system uncertainty is less than 0.004%. The system uncertainty introduced by pressure measurement is small and can be neglected, but the system uncertainty from frequency measurement has a great effect. The precisely measurement of resonance frequency is key to ensure the accuracy of the system.

Medium damping influences on the resonant frequency and quality factor of piezoelectric circular microdiaphragm sensors

2011 ◽  
Vol 21 (4) ◽  
pp. 045002 ◽  
Author(s):  
M Olfatnia ◽  
Z Shen ◽  
J M Miao ◽  
L S Ong ◽  
T Xu ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Quality Factor

A Microcontroller Approach to Measuring Transmissibility of MEMS Devices

2015 ◽  
Vol 2015 (DPC) ◽  
pp. 001564-001593
Author(s):  
Chong Li ◽  
Yixuan Wu ◽  
Haoyue Yang ◽  
Luke L. Jenkins ◽  
Robert N. Dean ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Quality Factor ◽  
Real Time ◽  
High Speed ◽  
Mechanical Quality Factor ◽  
Quantization Noise ◽  
Mems Devices ◽  
Input And Output ◽  
Mechanical Quality ◽  
Mems Device

The transmissibility reveals two very useful characteristics of a micro-electro-mechanical systems (MEMS) device, the resonant frequency and the mechanical quality factor. Real time knowledge on these two important factors can enhance application performance or avoid potential problems from environmental disturbances due to fabrication tolerances and the resulting operational differences in otherwise identical devices. Expensive laboratory equipment is typically used to measure the transmissibility. However, these test systems are not readily adaptable to field use. Therefore, it is important to be able to measure the transmissibility using a real time technique with a simplified test setup. This study proposes a technique that can compute the transmissibility in real time using a low cost microcontroller. This technique utilizes two laser vibrometers to detect the input and output motions of the proof mass in a MEMS device, which are fed to high speed 500 KHz analog to digital converters (ADC) in the microcontroller. A filtering step is performed to decrease noise. After the sampling and pre-filtering, a Fast Fourier Transform (FFT) is performed to convert the time-domain signals to frequency domain signals. The amplitude of the output signal at each frequency is divided by the amplitude of the corresponding input signal at each frequency to obtain the transmissibility. To overcome the difficulties resulting from measurement and quantization noise, a recursive calculating algorithm and a de-quantization filter are introduced. The recursive calculating process guarantees that the system updates the results continually, which results in a transmissibility plot covering the entire bandwidth. The de-quantization filter considers the validity of the data and performs the transmissibility division step accordingly. A cantilevered structure was chosen as the device-under-test to verify and evaluate this technique. The cantilevered device was attached to an electromechanical shaker system for vibratory stimulation. Two laser vibrometers were used to detect the input and output motion and this data was fed into a microcontroller. The microcontroller was STM32F407, which is 32-bit and 168 MHz controller. The tests demonstrated that this technique can measure the transmissibility and therefore the resonant frequency and mechanical quality factor accurately compared to a professional signal analyzer.

A MEMS PPA Based Active Vibration Isolator - STUDENT AWARD 3RD PLACE $500

2016 ◽  
Vol 2016 (DPC) ◽  
pp. 000853-000880
Author(s):  
Chong Li ◽  
C. Lavinia Elana ◽  
Robert N. Dean ◽  
George T. Flowers
Keyword(s):  
Resonant Frequency ◽  
Quality Factor ◽  
Proof Mass ◽  
Control Voltage ◽  
Stable Range ◽  
Vibration Isolator ◽  
Operating Range ◽  
Stable Operating ◽  
Mass Damper ◽  
Active Vibration

Several types of micro-devices are adversely affected by high frequency mechanical vibrations present in the operating environment. Examples include MEMS vibratory gyroscopes and resonators, and micro-optics. Various types of MEMS vibration isolators have been developed for use in the packaging of these vibration sensitive devices. Passive isolators consist of a spring-mass-damper MEMS device and usually have a very high mechanical quality factor, which makes them susceptible to ringing at the isolator's resonant frequency. Active isolators have been realized by using state sensing of the proof mass motion and feeding one or more of these states back through an actuator to adjust the frequency response of the isolator. For example, the technique known as skyhook damping uses velocity feedback to adjust, and typically increase, the damping of the isolator. Although these technique are doable, they require state sensing or state estimation, with feedback electronics to drive the actuator. A simpler MEMS active vibration isolator architecture employs only a parallel plate actuator (PPA) with the MEMS spring-mass-damper structure. The PPA driven with a DC voltage, in its stable operating range, displaces the proof mass, which results in a change in the effective system spring constant due to the electrostatic spring softening effect. This results in a change in the resonant frequency and the quality factor of the isolator. However, due to the nonlinearities inherent in this type of device, the stable operating range is reduced as the PPA voltage is increased. Furthermore, even when the isolator is stable in steady-state, a sufficiently large transient response can also drive it into the unstable regime, resulting in the electrodes snapping into contact. In this study, the PPA based active vibrator isolator is developed and its performance is evaluated. The characteristics of the transient instability are investigated and its stable range of operation is specified, for booth external disturbances and rapid application of the control voltage. This MEMS PPA based active vibration isolator can improve performance compared to passive isolators, while being much simpler than state feedback active isolators.

scholarly journals A Geometrical Study on the Roof Tile-Shaped Modes in AlN-Based Piezoelectric Microcantilevers as Viscosity–Density Sensors

Sensors ◽  
2019 ◽  
Vol 19 (3) ◽  
pp. 658 ◽  
Author(s):  
Víctor Ruiz-Díez ◽  
Javier Toledo ◽  
Jorge Hernando-García ◽  
Abdallah Ababneh ◽  
Helmut Seidel ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Quality Factor ◽  
Q Factor ◽  
Liquid Media ◽  
Roof Tile ◽  
Aln Film ◽  
Monitoring Applications ◽  
Media Monitoring ◽  
Comprehensive Study

Cantilever resonators based on the roof tile-shaped modes have recently demonstrated their suitability for liquid media monitoring applications. The early studies have shown that certain combinations of dimensions and order of the mode can maximize the Q-factor, what might suggest a competition between two mechanisms of losses with different geometrical dependence. To provide more insight, a comprehensive study of the Q-factor and the resonant frequency of these modes in microcantilever resonators with lengths and widths between 250 and 3000 µm and thicknesses between 10 and 60 µm is presented. These modes can be efficiently excited by a thin piezoelectric AlN film and a properly designed top electrode layout. The electrical and optical characterization of the resonators are performed in liquid media and then their performance is evaluated in terms of quality factor and resonant frequency. A quality factor as high as 140 was measured in isopropanol for a 1000 × 900 × 10 µm3 cantilever oscillating in the 11th order roof tile-shaped mode at 4 MHz; density and viscosity resolutions of 10−6 g/mL and 10−4 mPa·s, respectively are estimated for a geometrically optimized cantilever resonating below 1 MHz.

scholarly journals A Study on the Trimming Effects on the Quality Factor of Micro-Shell Resonators Vibrating in Wineglass Modes

Micromachines ◽  
2019 ◽  
Vol 10 (10) ◽  
pp. 695
Author(s):  
Lu ◽  
Xi ◽  
Xiao ◽  
Shi ◽  
Zhuo ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Quality Factor ◽  
Second Harmonic ◽  
Great Influence ◽  
Fem Simulation ◽  
Q Factor ◽  
Thermoelastic Damping ◽  
Frequency Trimming ◽  
Quality Factor Q ◽  
Anchor Loss

Frequency trimming based on mass and stiffness modification is an important post-fabrication process for micro-shell resonators (MSRs). However, the trimming effects on the quality factor are seldom studied, although they may have great influence on the performance of the resonator. This paper presents a study on the quality factor (Q-factor) variation of trimmed micro-shell resonators (MSR). Thermoelastic damping (QTED) and anchor loss (Qanchor) are found to be the dominant energy loss mechanisms resulting in the reduction of the overall Q-factor, according to finite element method (FEM). The effects of different trimming methods on QTED and Qanchor are studied here, respectively. It is found that trimming grooves ablated in the rim of the resonator can cause a ~1–10% reduction of QTED, and the length of trimming groove is positively related to the reduction of QTED. The reduction of QTED caused by the mass adding process is mainly related to the thermal expansion coefficient and density of the additive and contact area between the resonator and additive masses. Besides, the first and second harmonic errors caused by asymmetrical trimming can cause a 10–90% reduction of Qanchor. Finally, trimming experiments were conducted on different resonators and the results were compared with FEM simulation. The work presented in this paper could help to optimize the trimming process of MSRs.

Sign in / Sign up

Export Citation Format

Share Document