Effect of the Ratio of Zn/Y on Microstructure and Mechanical Properties of As-Cast Mg-4Zn-xY Alloys

2013 ◽  
Vol 395-396 ◽  
pp. 201-204
Author(s):  
Feng Wang ◽  
Ji Bao Li ◽  
Ping Li Mao ◽  
Zheng Liu
Keyword(s):  
Mechanical Properties ◽  
Tensile Testing ◽  
Energy Dispersive Spectrum ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
X Ray ◽  
Uniformity Coefficient ◽  
Microstructure And Mechanical Properties ◽  
Second Phases

In order to investigate the ratio of Zn/Y on as-cast Mg-4Zn-xY (x=1, 2, 3 in wt. %), microstructure and mechanical properties are analyzed by scanning electronic microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectrum (EDS) and tensile testing. The results indicate that with the decrease of the ratio of Zn/Y, microstructures are refined more greatly and the spheroidization and uniformity coefficient are improved obviously, and the morphologies of second phases are changed from diversity to unity, resulting in an improvement of mechanical properties of alloys.

Effect of AlN on Microstructure and Mechanical Properties of Mg-Al-Zn Alloy

2011 ◽  
Vol 704-705 ◽  
pp. 1095-1099
Author(s):  
Peng Liu ◽  
Hao Ran Geng ◽  
Zhen Qing Wang ◽  
Jian Rong Zhu ◽  
Fu Sen Pan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Tensile Testing ◽  
Cast Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Microstructure And Mechanical Properties ◽  
Zn Alloy

Effects of AlN addition on the microstructure and mechanical properties of as-cast Mg-Al-Zn magnesium alloy were investigated using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and tensile testing. Five different samples were made with different amounts of AlN(0wt%, 0.12wt%, 0.30wt%, 0.48wt%, 0. 60wt%). The results show that the phases of as-cast alloy are composed of α-Mg,β-Mg17Al12. The addition of AlN suppressed the precipitation of the β-phase. And, with the increase of AlN content, the microstructure of β-phase was changed from the reticulum to fine grains. When AlN content was up to 0.48wt% in the alloy, the β-phase became most uniform distribution. After adding 0.3wt% AlN to Al-Mg-Zn alloy, the average alloy grain size reduced from 102μm to 35μm ,the tensile strength of alloy was the highest. The average tensile strength increased from 139MPa to 169.91MPa, the hardness increased from 77.7HB to 98.4HB, but the elongation changes indistinctively. However, when more amount of AlN was added, the average alloy grain size did not reduce sequentially and increased to 50μm by adding 0.6wt% AlN and the β-phase became a little more. Keywords: Al-Mg-Zn alloy; AlN; β-Mg17Al12; Tensile strength

Microstructure and Mechanical Properties of VTaTiMoAlx Refractory High Entropy Alloys

2017 ◽  
Vol 898 ◽  
pp. 638-642 ◽  
Author(s):  
Dong Xu Qiao ◽  
Hui Jiang ◽  
Xiao Xue Chang ◽  
Yi Ping Lu ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
X Ray Diffraction ◽  
Dendrite Structure ◽  
X Ray ◽  
High Entropy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Microstructure And Mechanical Properties

A series of refractory high-entropy alloys VTaTiMoAlx with x=0,0.2,0.6,1.0 were designed and produced by vacuum arc melting. The effect of added Al elements on the microstructure and mechanical properties of refractory high-entropy alloys were investigated. The X-ray diffraction results showed that all the high-entropy alloys consist of simple BCC solid solution. SEM indicated that the microstructure of VTaTiMoAlx changes from equiaxial dendritic-like structure to typical dendrite structure with the addition of Al element. The composition of different regions in the alloys are obtained by energy dispersive spectroscopy and shows that Ta, Mo elements are enriched in the dendrite areas, and Al, Ti, V are enriched in inter-dendrite areas. The yield strength and compress strain reach maximum (σ0.2=1221MPa, ε=9.91%) at x=0, and decrease with the addition of Al element at room temperature. Vickers hardness of the alloys improves as the Al addition.

Microstructure and Mechanical Properties of Fe-Cu-Ni Sinters Prepared by Ball Milling and Hot Pressing

2020 ◽  
Vol 405 ◽  
pp. 379-384
Author(s):  
Joanna Borowiecka-Jamrozek ◽  
Jan Lachowski
Keyword(s):  
Mechanical Properties ◽  
Hot Pressing ◽  
High Hardness ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Composition ◽  
Microstructure And Mechanical Properties ◽  
Static Tensile ◽  
Iron Based ◽  
Surface Observations

The main purpose of this work was to determine the effect of the powder composition on the microstructure and properties of iron-based sinters used as a matrix in diamond tools. The Fe-Cu-Ni sinters obtained from a mixture of ground powders were used for experiments. The influence of manufacturing process parameters on the microstructure and mechanical properties of sinters was investigated. Sintering was performed using hot-pressing technique in a graphite mould. The investigations of obtained sinters included: density, hardness, static tensile test, X-ray diffraction analysis, microstructure and fracture surface observations. The obtained results indicate that the produced sinters have good plasticity and relatively high hardness.

Characterization of Shivirtui Zeolite Modified with Aluminum Oxyhydroxide Nanofibers

2019 ◽  
Vol 942 ◽  
pp. 40-49
Author(s):  
Yulia Murashkina ◽  
Olga B. Nazarenko
Keyword(s):  
Chemical Properties ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
X Ray ◽  
Physical And Chemical ◽  
And Chemical Properties ◽  
Aluminum Oxyhydroxide

Natural zeolite of Shivirtui deposit (Russia) was modified with nanofibers of aluminum oxyhydroxide AlOOH. Aluminum oxyhydroxide nanofibers were produced at the heating and oxidation of aluminum powder with water. The properties of modified zeolite were investigated by means of X-ray diffraction, transmission electronic microscopy, scanning electronic microscopy, low-temperature nitrogen adsorption, thermal analysis, and Fourier transform infrared spectroscopy. It was found that water content in the modified sample of zeolite was about 15 %. Based on the study of the physical and chemical properties, shivirtui zeolite modified with nanofibers of aluminum oxyhydroxide can be proposed for use as a flame-retardant additive to polymers.

scholarly journals The Dehydrogenation Mechanism and Reversibility of LiBH4 Doped by Active Al Derived from AlH3

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 559 ◽  
Author(s):  
Qing He ◽  
Dongdong Zhu ◽  
Xiaocheng Wu ◽  
Duo Dong ◽  
Xiaoying Jiang ◽  
...  
Keyword(s):  
Reaction Products ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
Scanning Calorimetry ◽  
Mass Spectral Analysis ◽  
X Ray ◽  
Mass Spectral ◽  
Al Composite ◽  
Dehydrogenation Mechanism

A detailed analysis of the dehydrogenation mechanism and reversibility of LiBH4 doped by as-derived Al (denoted Al*) from AlH3 was performed by thermogravimetry (TG), differential scanning calorimetry (DSC), mass spectral analysis (MS), powder X-ray diffraction (XRD), scanning electronic microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR). The results show that the dehydrogenation of LiBH4/Al* is a five-step reaction: (1) LiBH4 + Al → LiH + AlB2 + “Li-Al-B-H” + B2H6 + H2; (2) the decomposition of “Li-Al-B-H” compounds liberating H2; (3) 2LiBH4 + Al → 2LiH + AlB2 + 3H2; (4) LiBH4 → LiH + B + 3/2H2; and (5) LiH + Al → LiAl + 1/2H2. Furthermore, the reversibility of the LiBH4/Al* composite is based on the following reaction: LiH + LiAl + AlB2 + 7/2H2 ↔ 2LiBH4 + 2Al. The extent of the dehydrogenation reaction between LiBH4 and Al* greatly depends on the precipitation and growth of reaction products (LiH, AlB2, and LiAl) on the surface of Al*. A passivation shell formed by these products on the Al* is the kinetic barrier to the dehydrogenation of the LiBH4/Al* composite.

Study of the Synthesis of Mullite From Kaolin-α-Al2O3 and Kaolin-Al(NO3)3

2012 ◽  
Vol 1481 ◽  
pp. 11-17
Author(s):  
E. M. Lozada ◽  
O. Alanís ◽  
F. Legorreta ◽  
L. E. Hernández
Keyword(s):  
Combustion Method ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
X Ray ◽  
Crystallographic Study ◽  
Incomplete Reaction ◽  
Α Al2o3

ABSTRACTThe synthesis of mullite from kaolin clay and two precursors of aluminum: α-Al2O3 and Al(NO3)3 was investigated. In order to study the temperature effect, the system kaolin-α-Al2O3 was calcined in air in a range of 1200 to 1500°C, for 2 h. For the system kaolin-Al(NO3)3, the combustion method was employed, using urea as fuel, and calcined in air at 1500°C for 2 h. The products were characterized by X-ray diffraction, scanning electronic microscopy (SEM), energy dispersive spectroscopy and particle size analysis in order to analyze and compare their morphology and structure. The crystallographic study revealed an incomplete reaction between the kaolin and the α-Al2O3. Nevertheless, in the system kaolin-Al(NO3)3, it was obtained mullite with high purity and trace amounts of cristobalite.

Fabrication and Magnetic Properties of Fe3O4 Nanobranches via a Simple Solvothermal Method

2011 ◽  
Vol 335-336 ◽  
pp. 934-939
Author(s):  
Z. F. Zi ◽  
Y. N. Liu ◽  
Q.C. Liu ◽  
Jian Ming Dai ◽  
Yu Ping Sun
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Solvothermal Method ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
X Ray ◽  
Water Solvent ◽  
Phase Spinel ◽  
Antisite Defects

Magnetite (Fe3O4) nanobranches were synthesized using an improved solvothermal technique in mixed ethanol and water solvent. Structural and magnetic properties were systematically investigated. X-ray diffraction results showed that the sample was single-phase spinel structure. The results of scanning electronic microscopy exhibited that the grains were regular like-branch with sizes from 3 to 6 μm in length and in diameter between 50 and 200 nm. The composition determined by energy dispersive spectroscopy was very close to the stoichiometry of Fe3O4. The saturation magnetizations (Ms) at 10 and 300 K of the synthesized Fe3O4nanobranches were much lower than the theoretical values. On one hand, it could be explained by obstructive magnetizing along their non-easy magnetic axes by the shape anisotropy of Fe3O4nanobranches, on the other hand, lesserMscan also be understood by the existence of antisite defects.

Influence of Temperature of Accumulative Roll Bonding on the Microstructure and Mechanical Properties of AA5251 Aluminum Alloy

2014 ◽  
Vol 59 (1) ◽  
pp. 127-131 ◽  
Author(s):  
J. Bogucka
Keyword(s):  
Mechanical Properties ◽  
Ambient Temperature ◽  
Accumulative Roll Bonding ◽  
Bonding Temperature ◽  
Tensile Tests ◽  
Structure Evolution ◽  
X Ray Diffraction ◽  
Roll Bonding ◽  
X Ray ◽  
Microstructure And Mechanical Properties

Abstract The influence of bonding temperature on microstructure and mechanical properties of AA5251 alloy sheets have been analyzed in the paper. The alloy was deformed with the method of accumulative roll bonding (ARB) in various temperature conditions i.e. at ambient temperature up to 5th cycle (ε = 4.0) and using pre-heating of sheet packs at 200°C and 300°C up to 10 cycles (ε = 8.0). The deformed material was subjected to structural observations using TEM, measurements of crystallographic texture with the technique of X-ray diffraction and tensile tests. It was established that the temperature of roll-bonding had a significant effect on the structure evolution and the observed changes of mechanical properties. High refinement of microstructure and optimum mechanical properties were obtained for the material processed at lower temperatures, i.e. at ambient temperature and pre-heating at 200°C. Recovery structure processes occurring during deformation were observed in the alloy bonded with pre-heating at 300°C and therefore mechanical properties were lower than for the alloy bonded at lower temperatures.

scholarly journals The Dehydrogenation Mechanism and Reversibility of LiBH4 Doped by Active Al* Derived from AlH3

2019 ◽  
Author(s):  
Qing He ◽  
Dongdong Zhu ◽  
Xiaocheng Wu ◽  
Duo Dong ◽  
Xiaoying Jiang ◽  
...  
Keyword(s):  
Reaction Products ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
Scanning Calorimetry ◽  
Mass Spectral Analysis ◽  
X Ray ◽  
Mass Spectral ◽  
Al Composite ◽  
Dehydrogenation Mechanism

A detailed analysis of the dehydrogenation mechanism and reversibility of LiBH4 doped by active Al* derived from AlH3 was performed by thermogravimetry (TG), differential scanning calorimetry (DSC), mass spectral analysis (MS), powder X-ray diffraction (XRD), scanning electronic microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The results show that the dehydrogenation of LiBH4/Al* is a five-step reaction: (1) LiBH4 + Al → LiH + AlB2 + “Li-Al-B-H” + B2H6 + H2; (2) the decomposition of "Li-Al-B-H" compounds liberating H2; (3) 2LiBH4 + Al → 2LiH + AlB2 + 3H2; (4) LiBH4 → LiH + B + 3/2H2; (5) LiH + Al → LiAl + 1/2H2. And the reversibility of LiBH4/Al* composite is based on equation as follows: LiH + LiAl + AlB2 + 7/2H2 ↔ 2LiBH4 + 2Al. The extent of dehydrogenation reaction between LiBH4 and Al* greatly depends on the precipitation and growth of reaction products (LiH, AlB2 and LiAl, etc.) on the surface of Al*. A passivation shell of Al* formed by these products is the kinetic barrier to the dehydrogenation of LiBH4/Al* composite.

scholarly journals Structure and composition of soils

2010 ◽  
Vol 4 (4) ◽  
pp. 259-263 ◽  
Author(s):  
Snezana Nenadovic ◽  
Milos Nenadovic ◽  
Ljiljana Kljajevic ◽  
Vladimir Pavlovic ◽  
Aleksandar Djordjevic ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Porous Structure ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
Characterization Methods ◽  
Soil Particles ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force

This paper presents a study of soils structure and composition using up to date technique, such as scanning electronic microscopy, atomic force microscopy, X-ray diffraction, X-ray fluorescence, as well as some other characterization methods. It was shown that soil particles have porous structure and dimensions in the range from several millimeters to several hundreds of nanometers and consist of different minerals such as kaolin, quartz and feldspate.

Sign in / Sign up

Export Citation Format

Share Document