Effect of AlN on Microstructure and Mechanical Properties of Mg-Al-Zn Alloy

2011 ◽  
Vol 704-705 ◽  
pp. 1095-1099
Author(s):  
Peng Liu ◽  
Hao Ran Geng ◽  
Zhen Qing Wang ◽  
Jian Rong Zhu ◽  
Fu Sen Pan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Tensile Testing ◽  
Cast Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Microstructure And Mechanical Properties ◽  
Zn Alloy

Effects of AlN addition on the microstructure and mechanical properties of as-cast Mg-Al-Zn magnesium alloy were investigated using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and tensile testing. Five different samples were made with different amounts of AlN(0wt%, 0.12wt%, 0.30wt%, 0.48wt%, 0. 60wt%). The results show that the phases of as-cast alloy are composed of α-Mg,β-Mg17Al12. The addition of AlN suppressed the precipitation of the β-phase. And, with the increase of AlN content, the microstructure of β-phase was changed from the reticulum to fine grains. When AlN content was up to 0.48wt% in the alloy, the β-phase became most uniform distribution. After adding 0.3wt% AlN to Al-Mg-Zn alloy, the average alloy grain size reduced from 102μm to 35μm ,the tensile strength of alloy was the highest. The average tensile strength increased from 139MPa to 169.91MPa, the hardness increased from 77.7HB to 98.4HB, but the elongation changes indistinctively. However, when more amount of AlN was added, the average alloy grain size did not reduce sequentially and increased to 50μm by adding 0.6wt% AlN and the β-phase became a little more. Keywords: Al-Mg-Zn alloy; AlN; β-Mg17Al12; Tensile strength

Microstructure and Mechanical Properties of TiNiFe Shape Memory Alloys with Different Compositions

2016 ◽  
Vol 849 ◽  
pp. 295-301 ◽  
Author(s):  
Yan Feng Li ◽  
Xue Feng ◽  
Xun Jun Mi ◽  
Xiang Qian Yin ◽  
Xiao Yu Kang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Tensile Test ◽  
Shape Memory ◽  
Lattice Constant ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Content ◽  
Microstructure And Mechanical Properties

The microstructure and mechanical properties of TiNiFe alloys with different compositions was investigated by tensile test, X-ray diffraction, EBSD, SEM, and TEM. The results indicated that tensile strength rapidly increased with increasing Ni content. In addition, Ti2(Ni,Fe) particles were observed in the TiNiFe alloys, which affected the mechanical properties. Increasing the content of Ni had little influence on the grain size of TiNiFe alloys. With the replacement of Ni by Fe, the lattice constant of TiNiFe alloys decreased as the Ni content increased.

Effect of Nd Content and Heat Treatment on Microstructure and Mechanical Properties of Mg-Zn-Nd Alloy

2017 ◽  
Vol 898 ◽  
pp. 124-130 ◽  
Author(s):  
Shu Min Xu ◽  
Xin Ying Teng ◽  
Xing Jing Ge ◽  
Jin Yang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Second Phase ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Microstructure And Mechanical Properties

In this paper, the microstructure and mechanical properties of the as-cast and heat treatment of Mg-Zn-Nd alloy was investigated. The alloy was manufactured by a conventional casting method, and then subjected to a heat treatment. The results showed that the microstructure of as-cast alloy was comprised of α-Mg matrix and Mg12Nd phase. With increase of Nd content, the grain size gradually decreased from 25.38 μm to 9.82 μm. The ultimate tensile strength and elongation at room temperature of the Mg94Zn2Nd4 alloy can be reached to 219.63 MPa and 5.31%. After heat treatment, part of the second phase dissolved into the magnesium matrix and the grain size became a little larger than that of the as-cast. The ultimate tensile strength was declined by about 2.5%, and the elongation was increased to 5.47%.

Effect of the Ratio of Zn/Y on Microstructure and Mechanical Properties of As-Cast Mg-4Zn-xY Alloys

2013 ◽  
Vol 395-396 ◽  
pp. 201-204
Author(s):  
Feng Wang ◽  
Ji Bao Li ◽  
Ping Li Mao ◽  
Zheng Liu
Keyword(s):  
Mechanical Properties ◽  
Tensile Testing ◽  
Energy Dispersive Spectrum ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
X Ray ◽  
Uniformity Coefficient ◽  
Microstructure And Mechanical Properties ◽  
Second Phases

In order to investigate the ratio of Zn/Y on as-cast Mg-4Zn-xY (x=1, 2, 3 in wt. %), microstructure and mechanical properties are analyzed by scanning electronic microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectrum (EDS) and tensile testing. The results indicate that with the decrease of the ratio of Zn/Y, microstructures are refined more greatly and the spheroidization and uniformity coefficient are improved obviously, and the morphologies of second phases are changed from diversity to unity, resulting in an improvement of mechanical properties of alloys.

A Study on Copper Alloy C194 Lead Frame Grain Size Correlation to the Mechanical Properties Variations in Microelectronic Assembly Line

2012 ◽  
Vol 516-517 ◽  
pp. 1902-1905 ◽  
Author(s):  
Abd Rashid Amirul ◽  
Yusoff Mahani
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Copper Alloy ◽  
Assembly Line ◽  
Lead Frame ◽  
X Ray Diffraction ◽  
X Ray ◽  
Die Attach ◽  
Typical Performance

Copper alloy C194 lead frame occasionally has been observed creates non-sticking defect at wire bond process in typical microelectronic assembly line. The effect was significantly assessed as process variation during die attach. In this study, microstructure and mechanical properties of copper alloy lead frames were investigated. The copper alloy lead frames were selected from different batches in the production line that produced sticking (typical performance) and non-sticking defect. The micro structural and structural properties were investigated by means of optical microscopy (OM) and X-ray diffraction (XRD), respectively. The hardness and tensile strength were also determined. The result revealed that non-sticking lead frame has larger grain size of 43.8 nm than typical performance lead frame. Due to lower dislocation density, tensile strength and hardness of typical lead frame with smaller grain size were higher than that of defect lead frame. Elongation of defect lead frame was reached above 10% as compared to typical performance lead frame groups with the value below 4%.

HAp/TiO2 nanocomposites: Influence of TiO2 on microstructure and mechanical properties

2019 ◽  
Vol 54 (6) ◽  
pp. 765-772 ◽  
Author(s):  
Ajay Kumar Vemulapalli ◽  
Rama Murty Raju Penmetsa ◽  
Ramanaiah Nallu ◽  
Rajesh Siriyala
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Flexural Strength ◽  
Bone Growth ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructure And Mechanical Properties ◽  
Energy Ball

Hydroxyapatite is a very attractive material for artificial implants and human tissue restorations because they accelerate bone growth around the implant. The hydroxyapatite nanocomposites (HAp/TiO2) were produced by using high energy ball milling. X-ray diffraction studies revealed the formation of HAp and TiO2 composites. Cubic-like crystals with boundary morphologies were observed; it was also found that the grain size gradually increased with the increase in TiO2 content. It was found that the mechanical properties (hardness, Young's modulus, fracture toughness, flexural strength, and compression strength)of the composites significantly improved with the addition of TiO2, which was sintered at 1200℃. These properties were then also correlated with the microstructure of the composites. This paper investigates the effect of titania (TiO2 = 0, 5, 10, 15, 20, and 25 wt%) addition on the microstructure and mechanical properties of hydroxyapatite (Ca10(PO4)6(OH)2) nanocomposites.

Microstructure and Mechanical Properties of an Al-Cu-Mg-Fe-Ni Alloy

2014 ◽  
Vol 988 ◽  
pp. 156-160
Author(s):  
Hong Wei Liu ◽  
Feng Wang ◽  
Bai Qing Xiong ◽  
Yong An Zhang ◽  
Zhi Hui Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cast Alloy ◽  
Tensile Tests ◽  
Eutectic Structure ◽  
Test Results ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructure And Mechanical Properties ◽  
Ni Alloy ◽  
Scanning Electron

The microstructure and mechanical properties of the Al-2.24Cu-1.42Mg-0.9Fe-0.9Ni alloy were studied using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), and tensile tests. The results indicate that the microstructures of the as cast alloy involve α-Al matrix, Al/Al2CuMg eutectic structure, Al7Cu2Fe, Al7Cu4Ni and Al9FeNi compounds. The tensile test results indicate that the alloy at elevated temperature (200°C) displays superior tensile strength due to the presence of the thermally stable Al7Cu2Fe, Al7Cu4Ni and Al9FeNi compounds.

Effects of Sb on Microstructure and Mechanical Properties of Mg-5.5Al-1.2Y Alloy

2011 ◽  
Vol 194-196 ◽  
pp. 1374-1377
Author(s):  
Chang Qing Li ◽  
Quan an Li ◽  
Xing Yuan Zhang ◽  
Qing Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Room Temperature ◽  
Optical Microscope ◽  
High Melting ◽  
X Ray Diffraction ◽  
High Melting Point ◽  
X Ray ◽  
Microstructure And Mechanical Properties

The microstructure and mechanical properties of aged Mg-5.5Al-1.2Y magnesium alloy with Sb addition are investigated by optical microscope, SEM and X-ray diffraction analyzer. The results show that with proper content of Sb addition,the microstructure of Mg-5.5Al-1.2Y magnesium alloy is refined obviously and high melting point intermetallic compounds Sb3Y5 and Mg3Sb2 are formed. Meanwhile, the β-Mg17Al12 phase is more distributed. With the increase of Sb addition, the mechanical properties of the alloy at room and elevated temperature increase at first, and then decrease. When the content of Sb is up to 0.5%, the values of tensile strength and elongation at room temperature, 150ºC and 175ºC are up to their maxima synchronously, 241MPa /16.84%, 198MPa/20.27.86% and 169MPa/21.21% respectively.

Effect of Bactericidal Elements Addition on the Microstructure and Mechanical Properties of Ti34Nb Alloy

2017 ◽  
Vol 899 ◽  
pp. 185-190
Author(s):  
Esther Gil ◽  
Angèlica Amigó ◽  
Anna Igual Muñoz ◽  
Vicente Amigó
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Pure Titanium ◽  
Total Porosity ◽  
X Ray Diffraction ◽  
Silver Addition ◽  
X Ray ◽  
Ultrasonic Methods ◽  
Β Phase ◽  
Microstructure And Mechanical Properties

The functionalization of β-Ti alloys by the addition of small amounts of bactericidal elements is interesting for biomedical applications. Thus, alloying pure titanium with highly biocompatible elements such as Nb or Ta, stabilizes the β phase of the resulting alloy although they can also include difficulties during the fabrication process due to their refractory nature. This work studies the effect of small additions of Ag and Cu (1.5 to 3 wt.%) on the microstructure and mechanical properties of the Ti34Nb (wt.%) alloy processed by powder metallurgy. The blend elemental powders were mixed (30 rpm during 30 min). The samples were compacted at 600 MPa and sintered at 1250 oC during 3 hours. The microstructure was analyzed by X-Ray Diffraction (XRD) and Field Emission Scanning Electron Microscope with X-Ray Spectroscopy (FE-SEM/EDS). The mechanical properties were obtained by bending tests; the elastic modulus was measured by ultrasonic methods and the porosity by Archimedes test. Cu addition generates the appearance of α phase sheets inside the β phase grains. Cu also decreases the open porosity and increases the closed porosity of the material. On the contrary, Ag addition does not influence the stabilization of the β phase and it does not modify the density, thus the total porosity of the resulting material. With respect to the influence of the alloying elements on the elastic modulus (E) of the alloys, the E of the Ti34Nb (76.8 GPa) increases with the Cu addition (92.6 GPa) and decreases with the Ag one (68.9 GPa). Therefore, silver addition, which does not modify the microstructure and slightly decrease the mechanical properties of the Ti34Nb, can be considered a good alloying element to provide antibacterial features to the titanium alloy without losing performance.

Microstructure and Mechanical Properties of VTaTiMoAlx Refractory High Entropy Alloys

2017 ◽  
Vol 898 ◽  
pp. 638-642 ◽  
Author(s):  
Dong Xu Qiao ◽  
Hui Jiang ◽  
Xiao Xue Chang ◽  
Yi Ping Lu ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
X Ray Diffraction ◽  
Dendrite Structure ◽  
X Ray ◽  
High Entropy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Microstructure And Mechanical Properties

A series of refractory high-entropy alloys VTaTiMoAlx with x=0,0.2,0.6,1.0 were designed and produced by vacuum arc melting. The effect of added Al elements on the microstructure and mechanical properties of refractory high-entropy alloys were investigated. The X-ray diffraction results showed that all the high-entropy alloys consist of simple BCC solid solution. SEM indicated that the microstructure of VTaTiMoAlx changes from equiaxial dendritic-like structure to typical dendrite structure with the addition of Al element. The composition of different regions in the alloys are obtained by energy dispersive spectroscopy and shows that Ta, Mo elements are enriched in the dendrite areas, and Al, Ti, V are enriched in inter-dendrite areas. The yield strength and compress strain reach maximum (σ0.2=1221MPa, ε=9.91%) at x=0, and decrease with the addition of Al element at room temperature. Vickers hardness of the alloys improves as the Al addition.

Microstructure and Mechanical Performance of AZ31-1.7 Wt.% Si Alloy Processed by Cyclic Channel Die Compression

2010 ◽  
Vol 667-669 ◽  
pp. 457-461
Author(s):  
Wei Guo ◽  
Qu Dong Wang ◽  
Man Ping Liu ◽  
Tao Peng ◽  
Xin Tao Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Chinese Script ◽  
Cast State ◽  
Microstructure And Mechanical Properties ◽  
Mean Grain Size ◽  
The Matrix ◽  
The Mean

Cyclic channel die compression (CCDC) of AZ31-1.7 wt.% Si alloy was performed up to 5 passes at 623 K in order to investigate the microstructure and mechanical properties of compressed alloys. The results show that multi-pass CCDC is very effective to refine the matrix grain and Mg2Si phases. After the alloy is processed for 5 passes, the mean grain size decreases from 300 μm of as-cast to 8 μm. Both dendritic and Chinese script type Mg2Si phases break into small polygonal pieces and distribute uniformly in the matrix. The tensile strength increases prominently from 118 MPa to 216 MPa, whereas the hardness of alloy deformed 5 passes only increase by 8.4% compared with as-cast state.

Sign in / Sign up

Export Citation Format

Share Document