Heat Transfer Enhancement in Microchannel Using Nanofluids

2013 ◽  
Vol 465-466 ◽  
pp. 536-540
Author(s):  
Khairul Afif Fadzin ◽  
Ann Lee
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Pure Water ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Particle Volume ◽  
Better Than

Numerical investigation of heat transfer enhancement in two-dimensional microchannel heat sink (MCHS) using Al2O3-water, CuO-water and TiO2-water was conducted. The effect of different type of nanoparticles at particle volume concentration of 1%, 2% and 5% on the thermal performance in the MCHS was examined. The thermal performance is increased when nanofluids with high thermal conductivity and low dynamic viscosity was used. As the particle volume concentration increases, the heat transfer performance also improved. The result shows that the heat transfer performance of all the nanofluids used in this study was better than that of pure water. Overall, nanofluids with Al2O3-water at 5% particle volume concentration show the best cooling performance.

scholarly journals An Experimental Study on Heat Transfer and Pressure Drop of CuO-Water Nanofluid

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Bayram Sahin ◽  
Eyuphan Manay ◽  
Eda Feyza Akyurek
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Performance ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Horizontal Tube ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Particle Volume

Heat transfer and pressure drop characteristics of water based CuO nanofluid inside a horizontal tube were investigated experimentally. The upper limitation of the particle volume fraction with respect to heat transfer performance was also found. CuO-water nanofluids with volume fractions of 0.5%, 1%, 2%, and 4% were prepared by dispersing the CuO nanoparticles with an average diameter of 33 nm into deionised water. Experiments were carried out under the steady-state, constant heat flux, and turbulent flow regime conditions. The variations of the average Nusselt number and the friction factor with the Reynolds number were presented. For all given particle volume concentrations, heat transfer enhancements were calculated. It was concluded that the particle volume concentrations higher than 1% vol. were not appropriate with respect to the heat transfer performance of the CuO-water nanofluid. No heat transfer enhancement was observed at Re = 4.000. The highest heat transfer enhancement was achieved at Re = 16.000 and ф = 0.005.

Comparative Study of Cooling Performance of Automobile Radiator Using Al2O3-Water and Carbon Nanotube-Water Nanofluid

2014 ◽  
Vol 5 (1) ◽  
Author(s):  
Sandesh S. Chougule ◽  
S. K. Sahu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Base Fluid ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Transfer Performance ◽  
Nanoparticle Concentration ◽  
Cooling Performance ◽  
Forced Convective Heat Transfer ◽  
Better Than

In the present study, the forced convective heat transfer performance of two different nanofluids, namely, Al2O3-water and CNT-water has been studied experimentally in an automobile radiator. Four different concentrations of nanofluid in the range of 0.15–1 vol. % were prepared by the additions nanoparticles into the water as base fluid. The coolant flow rate is varied in the range of 2 l/min–5 l/min. Nanocoolants exhibit enormous change in the heat transfer compared with the pure water. The heat transfer performance of CNT-water nanofluid was found to be better than Al2O3-water nanocoolant. Furthermore, the Nusselt number is found to increase with the increase in the nanoparticle concentration and nanofluid velocity.

scholarly journals Enhanced heat transfer characteristics of conjugated air jet impingement on a finned heat sink

2017 ◽  
Vol 21 (1 Part A) ◽  
pp. 279-288 ◽  
Author(s):  
Shuxia Qiu ◽  
Peng Xu ◽  
Liping Geng ◽  
Arun Mujumdar ◽  
Zhouting Jiang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Air Jet

Air jet impingement is one of the effective cooling techniques employed in micro-electronic industry. To enhance the heat transfer performance, a cooling system with air jet impingement on a finned heat sink is evaluated via the computational fluid dynamics method. A two-dimensional confined slot air impinging on a finned flat plate is modeled. The numerical model is validated by comparison of the computed Nusselt number distribution on the impingement target with published experimental results. The flow characteristics and heat transfer performance of jet impingement on both of smooth and finned heat sinks are compared. It is observed that jet impingement over finned target plate improves the cooling performance significantly. A dimensionless heat transfer enhancement factor is introduced to quantify the effect of jet flow Reynolds number on the finned surface. The effect of rectangular fin dimensions on impingement heat transfer rate is discussed in order to optimize the cooling system. Also, the computed flow and thermal fields of the air impingement system are examined to explore the physical mechanisms for heat transfer enhancement.

Experimental Heat Transfer Enhancement in Single-Phase Liquid Microchannel Cooling With Cross-Flow Synthetic Jet

2010 ◽  
Author(s):  
Ruixian Fang ◽  
Wei Jiang ◽  
Jamil Khan ◽  
Roger Dougal
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Performance ◽  
Synthetic Jet ◽  
Driving Voltage ◽  
Transfer Performance ◽  
Microchannel Flow ◽  
Transfer Enhancement ◽  
Synthetic Jet Actuator ◽  
Phase Liquid

The present study experimentally investigated a new hybrid cooling scheme by combination of a microchannel heat sink with a micro-synthetic jet actuator. The heat sink consisted of a single rectangular microchannel measured 550 μm wide, 500 μm deep and 26 mm long. The synthetic jet actuator with a 100 μm diameter orifice was placed right above the microchannel and 5 mm downstream from the channel inlet. Micro jet is synthesized from the fluid flowing through the microchannel. Periodic disturbance is generated when the synthetic jet interacts with the microchannel flow. Heat transfer performance is enhanced as local turbulence is generated and propagated downstream the microchannel. The scale and frequency of the disturbance can be controlled by changing the driving voltage and frequency of the piezoelectric driven synthetic jet actuator. The effects of synthetic jet on microchannel heat transfer performance were studied based on the microchannel flow Reynolds number, the jet operating voltage and frequency, respectively. It shows that the synthetic jet has a greater heat transfer enhancement for microchannel flow at lower Reynolds number. It also shows that the thermal effects of the synthetic jet are functions of the jet driving voltage and frequency. We obtained around 42% heat transfer enhancement for some test cases, whereas the pressure drop across the microchannel increases very slightly. The paper concludes that the synthetic jet can effectively enhance single-phase liquid microchannel heat transfer performance and would have more promising enhancements if multi-jets are applied along the microchannel.

Heat Transfer Enhancement of Car Radiator Using Al₂ O₃ / Water Nanofluid in the Presence of Electric Field; an Experimental Study

2020 ◽  
pp. 15-24
Author(s):  
Koorosh Goudarzi ◽  
H. Jamali ◽  
V. Kalaei
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Electric Field ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Rate ◽  
Thermal Performance ◽  
Transfer Rate ◽  
Pure Water ◽  
Transfer Enhancement ◽  
Fan Speed

In this experimental study, Aluminums Oxide (Al2O3) in Pure Water (PW) as nanofluid was used for heat transfer enhancement in car radiator together with electric field. Electric field with different voltage 8, 11, 14 kV and nanofluids with volume concentrations of 0.08%, 0.5% and 1% were investigated. From the experiments, it was found that the unit with electric field pronounced better heat transfer rate, especially at low fan speed. In addition heat transfer coefficient and heat transfer rate in engine cooling system increased with the usage of nanofluids Al2O3/PW compared to Pure Water alone. With the use of nanofluid with concentration of 1% and electric field for fan speed 600 and 1200 rpm, thermal performance factors were in a range between, 1.8–3.2 and 1.6–1.74, respectively. Thermal performance factor is more than 1 in all of cases, and it can be concluded that this technique can be used in car radiators to improve heat transfer.

Effect of Protuberances in the Heat Transfer Enhancement in Mini-Channels

2021 ◽  
Author(s):  
Ariel Cruz Diaz ◽  
Gerardo Carbajal
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Performance ◽  
Heat Removal ◽  
Working Fluid ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Mini Channels

Abstract This study presents the effects of adding an array of protrusions in a microchannel for heat transfer enhancement. The presence of mini-channels increases the overall heat transfer area and boosts the mixing development near the solid-fluid interaction; therefore, it can remove more heat than conventional mini-channels without protuberances. A numerical study proved that protuberances in a mini-channel increase the heat transfer performance by disturbing the relative fluid motion near the solid wall. The numerical simulation was performed with three different protuberances arrays: aligned, staggered, and angular. Each array consists of a thin flat plate with a hemispherical shape; the working fluid and the solid materials were water and copper. The study also includes the effect of different Reynolds numbers: 1,000, 1,500, and 2,000. Three heat inputs were applied in the numerical simulation; these were 1W, 3W, and 5W. The study was compared with a simple microchannel with non-protuberances to analyze the microchannel performance regarding heat removal and pressure drop. For heat transfer performance, the best array was the staggering array with a maximum heat removal increase of 5.26 percent. In terms of pressure drop performance, the best array was the aligned array, with a maximum increase of 34.73 percent.

Enhancing Heat Transfer of Air-Cooled Heat Sinks Using Piezoelectrically-Driven Agitators and Synthetic Jets

2011 ◽  
Author(s):  
Youmin Yu ◽  
Terrence Simon ◽  
Min Zhang ◽  
Taiho Yeom ◽  
Mark North ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Single Channel ◽  
Synthetic Jets ◽  
Heat Sinks ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Enhancing Heat Transfer

Air-cooled heat sinks prevail in microelectronics cooling due to their high reliability, low cost, and simplicity. But, their heat transfer performance must be enhanced if they are to compete for high-flux applications with liquid or phase-change cooling. Piezoelectrically-driven agitators and synthetic jets have been reported as good options in enhancing heat transfer of surfaces close to them. This study proposes that agitators and synthetic jets be integrated within air-cooled heat sinks to significantly raise heat transfer performance. A proposed integrated heat sink has been investigated experimentally and with CFD simulations in a single channel heat sink geometry with an agitator and two arrays of synthetic jets. The single channel unit is a precursor to a full scale, multichannel array. The agitator and the jet arrays are separately driven by three piezoelectric stacks at their individual resonant frequencies. The experiments show that the combination of the agitator and synthetic jets raises the heat transfer coefficient of the heat sink by 80%, compared with channel flow only. The 3D computations show similar enhancement and agree well with the experiments. The numerical simulations attribute the heat transfer enhancement to the additional air movement generated by the oscillatory motion of the agitator and the pulsating flow from the synthetic jets. The component studies reveal that the heat transfer enhancement by the agitator is significant on the fin side and base surfaces and the synthetic jets are most effective on the fin tips.

Heat transfer performance of steam/air flow in inverted V-shaped rib-roughened channels

2021 ◽  
pp. 095765092110161
Author(s):  
Chao Ma ◽  
Bing Ge
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Performance ◽  
Air Flow ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Ribbed Channel

The heat transfer performance of steam and air flow in a rough rectangular channel with different inverted V-shaped ribs was investigated by infrared thermal imaging technology. Under the conditions that the Reynolds number is in the range of 4000–15,000, the effects of the rib angle on the heat transfer enhancement of the two coolants were obtained. The rib pitch ratio of the flow channel is 10, the ratio of the rib height to the channel hydraulic diameter is 0.078, and the inverted V-shaped rib angle varies from 45° to 90°. The results show that in the inverted V-shaped ribbed channel, the Nu number on both sides of the channel is greatly increased, while the Nu number in the middle of the channel is lower. The local Nu distribution on the surface of the ribbed channel is highly related to the shape of the rib. For different medium cooling, the value and unevenness of the heat transfer coefficient are different, but the shape of the high and low heat transfer coefficient distribution is hardly affected. The heat transfer of both coolants increases as the rib angle decreases from 90° to 45°. Compared with air flow, steam flow cooling shows higher convective heat transfer enhancement. For rib angles of 45°, 60°, 75°, and 90°, under the operating condition of the Reynolds number = 12,000, the area-averaged Nusselt numbers of the steam flow is 23.6%, 27.4% and 13.9% higher than that of the air flow, respectively. Based on the experimental heat transfer data, the correlation in terms of the Reynolds number and the rib angle was developed, which is used to estimate the Nu number for steam and air cooling in the inverted V-shaped rib-roughness channels.

Convective Heat Transfer Enhancement Using Carbon Nanofibers (CNFs): Influence of Amorphous Carbon Layer on Heat Transfer Performance

2013 ◽  
Author(s):  
T. J. Taha ◽  
L. Lefferts ◽  
T. H. Van der Meer
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Surface Area ◽  
Carbon Nanofibers ◽  
Amorphous Carbon ◽  
Heat Transfer Performance ◽  
Transfer Performance ◽  
Transfer Enhancement

In this work, an experimental heat transfer investigation was carried out to investigate the combined influence of both amorphous carbon (a-C) layer thickness and carbon nanofibers (CNFs) on the convective heat transfer behavior. Synthesis of these carbon nano structures was achieved using catalytic chemical vapor deposition process (CCVD) on a 50 μm nickel wire at 650°C. Due to their extremely high thermal conductivity, CNFs are used to augment/modify heat transfer surface. However, the inevitable layer of a-C that occurs during the synthesis of the CNFs layer exhibit low thermal conductivity which may result in insulating the surface. In contrast, the amorphous layer helps in supporting and mechanical stabilizing of the CNFs layer attachment to the polycrystalline nickel (Ni270) substrate material. To better understand the influences of these two layer on heat transfer, the growth mechanism of the CNFs layer and the layer of carbon is investigated and growth model is proposed. The combined impact of both a-C and CNFs layer on heat transfer performance is studied on three different samples which were synthesized by varying the deposition period (16 min, 23min and 30 min). The micro wire samples covered with CNF layers were subjected to a uniform flow from a nozzle. Heat transfer measurement was achieved by a controlled heat dissipation through the micro wire to attain a constant temperature during the flow. This measurement technique is adopted from hot wire anemometry calibration method. Maximum heat transfer enhancement of 18% was achieved. This enhancement is mainly attributed to the surface roughness and surface area increase of the samples with moderate CNFs surface area coverage on the sample.

Sign in / Sign up

Export Citation Format

Share Document