Research on the Surface Acoustic Wave Temperature Sensor

2014 ◽  
Vol 543-547 ◽  
pp. 1266-1269 ◽  
Author(s):  
Kun Zhang ◽  
Wen Di Wang ◽  
Zhao Mei Qiu
Keyword(s):  
Acoustic Wave ◽  
Temperature Measurement ◽  
Surface Acoustic Wave ◽  
Temperature Sensor ◽  
Measurement Accuracy ◽  
Temperature Characteristic ◽  
Experimental Results ◽  
Testing Unit ◽  
Saw Sensor ◽  
Frequency Temperature

This paper puts forward an idea of designing a surface acoustic wave (SAW) sensor to provide a research basis for subsequent researchers. We have made a SAW temperature sensor based on this idea. The experimental results demonstrated the feasibility of the idea, and shown that the frequency-temperature characteristic of the sensing unit is good and the temperature measurement accuracy of the testing unit is high.

A high sensitivity wireless mass-loading surface acoustic wave DNA biosensor

2014 ◽  
Vol 28 (07) ◽  
pp. 1450056 ◽  
Author(s):  
Hua-Lin Cai ◽  
Yi Yang ◽  
Yi-Han Zhang ◽  
Chang-Jian Zhou ◽  
Cang-Ran Guo ◽  
...  
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Dna Sequences ◽  
Biological Treatment ◽  
High Performance ◽  
Processing System ◽  
High Sensitivity ◽  
Treatment Method ◽  
Saw Sensor ◽  
Target Dna

In this paper, a surface acoustic wave (SAW) biosensor with gold delay area on LiNbO 3 substrate detecting DNA sequences is proposed. By well-designed device parameters of the SAW sensor, it achieves a high performance for highly sensitive detection of target DNA. In addition, an effective biological treatment method for DNA immobilization and abundant experimental verification of the sensing effect have made it a reliable device in DNA detection. The loading mass of the probe and target DNA sequences is obtained from the frequency shifts, which are big enough in this work due to an effective biological treatment. The experimental results show that the biosensor has a high sensitivity of 1.2 pg/ml/Hz and high selectivity characteristic is also verified by the few responses of other substances. In combination with wireless transceiver, we develop a wireless receiving and processing system that can directly display the detection results.

Development of ball surface acoustic wave gas chromatograph for environmental monitoring in spacecraft and its application on the ground

2022 ◽  
Author(s):  
Takamitsu Iwaya ◽  
Shingo Akao ◽  
Kazushi Yamanaka ◽  
Tatsuhiro Okano ◽  
Nobuo Takeda ◽  
...  
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Stationary Phases ◽  
Micro Electro Mechanical System ◽  
Steel Plates ◽  
Gas Chromatograph ◽  
Site Analysis ◽  
Saw Sensor ◽  
Ball Surface ◽  
Brewing Process

Abstract For on-site analysis of surface materials on the moon, planets, and small bodies and for the monitoring of air quality in crewed spacecraft, we have developed a portable gas chromatograph (GC) equipped with a ball surface acoustic wave (SAW) sensor. In this study, we fabricated a 10 cm cube GC that implements the forward flush method using two metal micro-electro-mechanical-system (MEMS) columns coated with different stationary phases in microchannels fabricated by wet etching and diffusion bonding of stainless-steel plates. Using this GC, we succeeded in analyzing 10 kinds of gas within 10 min. In addition, for the application of the ball SAW GC on the ground, we also developed a palm-sized GC with a single metal capillary column and used it in the analysis of the headspace gas of sake. We showed that the ratio of peak areas differed among odorants depending on the brand and brewing process of sake.

Improved Performance of Surface Acoustic Wave Sensors by Plasma Treatments for Chemical Warfare Agents Monitoring

2020 ◽  
Vol 20 (11) ◽  
pp. 7145-7150 ◽  
Author(s):  
Eunhyun Kim ◽  
Jinuk Kim ◽  
Seonggyun Ha ◽  
Changsik Song ◽  
Joo-Hyung Kim
Keyword(s):  
Acoustic Wave ◽  
Plasma Treatment ◽  
Surface Acoustic Wave ◽  
Chemical Warfare Agents ◽  
Chemical Warfare ◽  
Saw Sensor ◽  
Warfare Agents ◽  
Improved Performance ◽  
Lift Off ◽  
Sensing Performance

The effects of a plasma treatment on the sensing performance of surface acoustic wave (SAW) sensors to detect chemical warfare agents (CWAs) were investigated. SAW sensors designed for an operating frequency of 250 MHz were fabricated using lift-off techniques followed by the deposition of a very thin thiourea (TU) layer as a sensing film on the sensing area of the SAW sensor. To achieve some advantages from the plasma treatment on the surface, such as cleaning, surface activation and modification, a post-plasma treatment was performed on the sensing layer and the sensing performance of the SAW sensor was measured by a comparison with the measured responses, providing different simulant gases through the gas feeding system. The sensitivity test revealed significant improvement in the sensing ability of the SAW sensor to detect DMMP, a simulant of a CWA, but with a relatively longer recovery time. The responses of other simulants at different concentrations and different simulant vapors were compared. The results showed that a plasma treatment on the sensing layer of a SAW device can improve the selectivity and sensitivity to a certain target gas or some volatile organic compounds. Therefore, a plasma treatment will be very useful for improving the selectivity and sensitivity of SAW sensors for the detection of CWAs.

scholarly journals ZIF Nanocrystal-Based Surface Acoustic Wave (SAW) Electronic Nose to Detect Diabetes in Human Breath

Biosensors ◽  
2018 ◽  
Vol 9 (1) ◽  
pp. 4 ◽  
Author(s):  
Fabio Bahos ◽  
Arianee Sainz-Vidal ◽  
Celia Sánchez-Pérez ◽  
José Saniger ◽  
Isabel Gràcia ◽  
...  
Keyword(s):  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Signal Recovery ◽  
Exhaled Breath ◽  
Zeolitic Imidazolate Frameworks ◽  
Saw Sensor ◽  
Low Concentrations ◽  
Control Of Diabetes ◽  
Short Time ◽  
And Control

In the present work, a novel, portable and innovative eNose composed of a surface acoustic wave (SAW) sensor array based on zeolitic imidazolate frameworks, ZIF-8 and ZIF-67 nanocrystals (pure and combined with gold nanoparticles), as sensitive layers has been tested as a non-invasive system to detect different disease markers, such as acetone, ethanol and ammonia, related to the diagnosis and control of diabetes mellitus through exhaled breath. The sensors have been prepared by spin coating, achieving continuous sensitive layers at the surface of the SAW device. Low concentrations (5 ppm, 10 ppm and 25 ppm) of the marker analytes were measured, obtaining high sensitivities, good reproducibility, short time response and fast signal recovery.

Sign in / Sign up

Export Citation Format

Share Document