Experimental Research Regarding Static Rigidity in Axial Direction of "Narrow" Modules from Modular Fixtures Structure

2014 ◽  
Vol 657 ◽  
pp. 514-518 ◽  
Author(s):  
Dragoș Florin Chitariu
Keyword(s):  
Experimental Research ◽  
Research Methodology ◽  
Axial Direction ◽  
Experimental Results ◽  
Modular Structure ◽  
Total Deformation ◽  
Deformation Curves ◽  
Modular Fixtures ◽  
Static Rigidity

In the paper a research methodology was developed and used to determine the rigidity in the axial direction.The paper presents a the experimental results regarding the total deformation of narrow modules found in the structure of modular sets. The research conducted showed the different evolution of deformation curves in the case of modular structure composed of modules, with different shape and different sizes, in the case of similar loads

Experimental Research Regarding Static Rigidity in Transversal Direction of “Narrow“ Modules from Modular Fixtures Structure

2015 ◽  
Vol 809-810 ◽  
pp. 754-759 ◽  
Author(s):  
Dragoş Florin Chitariu
Keyword(s):  
Angular Displacement ◽  
Base Plate ◽  
Linear Displacement ◽  
Experimental Results ◽  
Modular Structure ◽  
Total Deformation ◽  
Deformation Curves ◽  
Modular Fixtures ◽  
Static Rigidity ◽  
Measurement Base

In the paper a research methodology was developed and used to determine the rigidity in transversal direction of modular fixture structures. The paper presents experimental results regarding the total deformation of modular structure consisting of ”narrow” modules from modular kits. The research conducted showed the different evolution of deformation curves in the case of modular structure, with different shape and different sizes of modules, in the case of similar loads. The experimental results indicate displacements of the entire modular structure alongside the base plate and, also, tilting. The measured deviations of modules from fixture structure may cause "dimensional"/ position deviations (linear displacement of the measurement base) and deviations of shape and orientation-position (angular displacement of the measurement base) of the workpiece during severe machining conditions.

Experimental Research to Evaluate Thermal Behavior of a Brushless Driving Servomotor for Linear Motion NC Axis Experimental Stand

2015 ◽  
Vol 762 ◽  
pp. 55-60
Author(s):  
Georgia Cezara Avram ◽  
Florin Adrian Nicolescu ◽  
Radu Constantin Parpală ◽  
Constantin Dumitrascu
Keyword(s):  
Thermal Behavior ◽  
Mathematical Models ◽  
Experimental Research ◽  
Infrared Imaging ◽  
Experimental Results ◽  
Ball Screw ◽  
Linear Motion ◽  
Functional Optimization ◽  
Thermal Infrared Imaging ◽  
Experimental Stand

This paper presents the works carried out by the authors in the field of structural and functional optimization of industrial robot's numerically controlled (NC) axes. The study includes the results obtained in the research stage of the experimental measurements performed to evaluate the electrical servomotor's thermal behavior using a thermal (infrared) imaging camera. The analyzed servomotor is a brushless servomotor integrated in an experimental stand for linear motion NC axis experimental research, existing in the MMS department from EMTS faculty. Supplementary to the driving servomotor, the experimental stand includes a belt drive transmission, a ball screw - bearings assembly and a driven element guided by ball rail system. This experimental research phase is part of the doctoral thesis of first author and was conducted in order to validate the mathematical models developed in the PhD thesis. Thus, experimental results presented in the paper have been used to validate first mathematical models for electric motor's preliminary selection and checking, (performed by determining the total reflected inertia of the mechanical system on motor shaft level) as well as the mathematical models for final selection and checking (by evaluating the servomotor's thermal energy dissipation, and servomotor's internal and external maximum operating temperature). Second, the experimental results have been used to validate the assisted simulation for structural and functional optimization of industrial robot's NC axes based on both servomotor and drive's thermal behavior analysis, performed in the thesis by means of a dedicated commercial software package.

Experimental Research on Rotating Skimmer

2003 ◽  
Author(s):  
Minoru Chino ◽  
Kenji Takizawa ◽  
Takashi Yabe
Keyword(s):  
Experimental Research ◽  
Rotational Speed ◽  
Rotation Speed ◽  
Experimental Results ◽  
Injection System ◽  
Benchmark Test ◽  
Injection Speed ◽  
Structure Interaction ◽  
Wide Range ◽  
Computer Codes

This paper provides the experimental results on skimmer and gives some detailed information useful for benchmark test of computer codes that are now able to simulate the fluid-structure interaction. For this purpose, we specially designed the injection system that imposes reproducible rotational speed and injection speed on the skipper. The effect of rotation is discussed by changing rotation speed in a wide range.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

Studies on the Influence of Sintering Parameters on the Hardness and Impact Energy of Some Sintered Steels Alloyed with Copper Powders

2015 ◽  
Vol 1128 ◽  
pp. 80-87
Author(s):  
Claudiu Nicolicescu ◽  
Iulian Ştefan ◽  
Victor Horia Nicoară
Keyword(s):  
Experimental Research ◽  
Impact Energy ◽  
Copper Content ◽  
Argon Atmosphere ◽  
Experimental Results ◽  
Sintered Steels ◽  
Copper Powders ◽  
Carburizing Process

The paper presents experimental results regarding the evolution of hardness and impact energy of some sintered steels alloyed with 1.5% respective 3% (weight) copper powders. For the experimental research were used 3 mixtures: Fe+0.2C as reference, Fe+0.2C+1.5Cu, Fe+0.2C+3Cu. All the samples were die pressed at three pressures 400, 500 and 600 MPa and were subjected at three types of treatments as following: SINT, SINTCARB and CARBSINT. For the sintering treatments was used argon atmosphere and for carburizing process was used methane. After each treatment the hardness and impact energy for all the samples were measured and were made correlations between these properties and the type of treatment and copper content.

Methodology for the Research Conducted

2021 ◽  
pp. 190-226
Keyword(s):  
Experimental Research ◽  
Research Methodology ◽  
Systems Design ◽  
Controlled Environment ◽  
Research Methodologies ◽  
In The Wild ◽  
The Individual

This chapter describes and discusses a combination of research methodologies (e.g., experimental, theoretical, and systems design) used in this research, allowing us to eliminate as much as possible every limitation that can be encountered with the individual methods themselves. For example, experimental research methodology has a limitation because the experiments are performed mainly in a controlled environment and might not reflect properly some practices performed ‘in the wild'. But combining this with some survey and prototype (system's) design reduced such limitations. The knowledge gained from carrying out preliminary experimentation is used in the next chapter to design and model the Hybrid-AutoML system.

The Research of the Chemistry Composition of High Temperature Oxidization under Loads for the Cr5Mo Alloy

2011 ◽  
Vol 694 ◽  
pp. 729-732
Author(s):  
Shun Qing Chen ◽  
Yu Min Ma
Keyword(s):  
High Temperature ◽  
Experimental Research ◽  
Experimental Results ◽  
The Difference

The chemistry composition of the high temperature oxidization under loads has been analyzed for the Cr5Mo alloy in this paper. The experimental research to the Fe, Cr and O elements have also been done. The difference between loads and no loads has been emphasized to the chemistry elements of the Cr5Mo alloy. The experimental results showed that the temperature couldn’t change the rate of the chemistry elements, but the loads could change them. The chemistry elements Fe ，Mo and Cr could change more obvious than other elements of the Cr5Mo alloy in this paper.

scholarly journals Numerical analysis of the impact of removing a corner column in a continuous slab-column structure in relation to the experimental model

2020 ◽  
Vol 310 ◽  
pp. 00054
Author(s):  
Miroslaw Wieczorek
Keyword(s):  
Numerical Analysis ◽  
Numerical Modelling ◽  
Experimental Model ◽  
Experimental Research ◽  
Experimental Results ◽  
Numerical Calculations ◽  
Column Structure ◽  
Continuous Slab ◽  
The Impact ◽  
Model Support

The paper presents the numerical analysis of the impact of removing a corner column on the behavior of a continuous slab-column structure. The model uses the minimal reinforcement amount compliant with Eurocodes. The basis for numerical modelling was the experimental research of a piece of a slab-column structure with the dimensions of 3.0×3.0 m in column axes. The article includes a detailed description of the assumed conditions of the model support, the method of loading and reading of the results. The paper also compares the obtained results of numerical calculations with experimental results.

Experimental Research on Influences on Mechanical Property of C50 Waterproof Concrete by Basalt Fiber

2013 ◽  
Vol 834-836 ◽  
pp. 755-761
Author(s):  
Hai Liang Wang ◽  
Hai Yang Guo ◽  
Xin Lei Yang ◽  
Quan Chang Ren ◽  
Peng Dong
Keyword(s):  
Mechanical Property ◽  
Experimental Research ◽  
Brittle Failure ◽  
Fracture Resistance ◽  
Test Specimen ◽  
Polypropylene Fiber ◽  
Basalt Fiber ◽  
Experimental Results ◽  
Regular Patterns ◽  
Failure Character

The experiment discussed influences of basalt fiber with different adulterate amount to the compressive and fracture resistance properties of waterproof concrete C50. We also made comparison between experimental results and mechanical property of polypropylene fiber waterproof concrete. The experimental results demonstrated that the brittle failure character of waterproof concrete has been improved to some extent, and the compressive and fracture resistance strength of the test specimen has increased apparently after adulterating basalt fiber and polypropylene fiber. Furthermore, it is mainly unanimous of the influence regular patterns of basalt fiber and polypropylene fiber to waterproof concrete when adulterating the same amount.

Experimental Research Regarding the Influence of Hydraulic Resistances on the Hydrostatic Guideways Stiffness

2014 ◽  
Vol 657 ◽  
pp. 475-479
Author(s):  
Marius Pascu ◽  
Gheorghe Stan
Keyword(s):  
Machine Tool ◽  
Hydraulic Resistance ◽  
Experimental Research ◽  
Machine Tools ◽  
Dynamic Stiffness ◽  
Experimental Results ◽  
Graphical Form ◽  
Experimental Setup ◽  
Experimental Database ◽  
Supply Circuit

A very important factor for the hydrostatic guideways is given by the presence of the restrictor on the supply circuit, whose hydraulic resistance may have important effects on the lubricant film behaviour and implicitly, on the static and dynamic stiffness of the system. This paper presents a new method of experimental research regarding the hydrostatic guideway stiffness, depending on the hydraulic resistances values which supply each pocket. During the experiments which approach the influence of the hydraulic resistances values of the restrictors on the hydrostatic guideway stiffness, a centered constant loads of 20, 50 and 100 [daN] was used. The experiments were carried out on an experimental setup composed of an open hydrostatic guideway, having the pocket dimensions of 150x88 [m, supplied with liquid under pressure through means of a pack of adjustable restrictors. The obtained experimental results are presented in both tabular and graphical form and constitute an experimental database which can be used by the machine tools designers and manufacturers. The paper contains recommendations regarding the usage of hydraulic resistances values depending on the machine tool type and size. Also, from the obtained results, recommendations can be made with regard to the type of restrictors to be used, so that the lubricant filtration grade is comprised between admissible values.

Sign in / Sign up

Export Citation Format

Share Document