Characterization of Physical and Mechanical Properties of Bleaching Paper from Rice Straw

2019 ◽  
Vol 891 ◽  
pp. 3-8 ◽  
Author(s):  
Udomdeja Polyium ◽  
Thanapan Boonyaratakalin ◽  
Songsiri Wichiranon
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Rice Straw ◽  
Physical And Mechanical Properties ◽  
Optimal Conditions ◽  
Tear Strength ◽  
Burst Strength ◽  
Bleached Pulp ◽  
Unbleached Pulp

This paper aimed to determine the characteristics of physical and mechanical properties of rice straw hand sheet and investigated the optimal conditions for making rice straw paper. The chemical composition of rice straw determined with the TAPPI standards. The conditions of making paper hand sheet composed of pulping time: 2 hours, 4 hours, pulping temperature: 100°C, 130°C, pulping solvent: 2 wt% NaOH, 4 wt% NaOH and bleaching: unbleached pulp, bleached pulp with 2% H2O2. The paper hand sheet was tested based on TAPPI methods, basic weight TAPPI- T410-om-93, thickness TAPPI- T411-om-89, moisture content TAPPI- T412-om-93, brightness TAPPI T452 om-92, opacity TAPPI standard T 425 om-91, burst strength TAPPI T403 om-97, tensile strength TAPPI T494 om-01, and tear strength TAPPI-T414-om-88. The results showed that the optimal conditions of rice straw hand sheet including pulping time: 2 hours, pulping temperature: 100°C, pulping solvent: 2 wt% NaOH, and bleaching: unbleached pulp gave the highest the physical and mechanical properties form other conditions. This conditions showed as the basic weight 62.27 g/m2, thickness 259.30 µ, opacity 93.34 ISO%, burst strength 64.75 kPa.m2/g, tensile strength 95.33 N.m/g, and tear strength 473.55mN.m2/g. In this condition, the paper hand sheet used at the lowest concentration of pulping solvent and non-bleached, which reduces environmental pollution.

APPROACHES TO CONTROLLING MICRO-ORGANISMS IN COTTON AND COTTON/ELASTANE CLOTHINGS

2021 ◽  
Vol 16 (3) ◽  
pp. 124-135
Author(s):  
Nilüfer Yıldız Varan
Keyword(s):  
Mechanical Properties ◽  
Antimicrobial Activity ◽  
Tensile Strength ◽  
Untreated Control ◽  
Physical And Mechanical Properties ◽  
Emergency Rooms ◽  
Tear Strength ◽  
Antifungal Properties ◽  
Micro Organisms ◽  
Control Samples

Antimicrobials are substances or mixtures of substances used to destroy or suppress the growth of harmful microorganisms such as bacteria, viruses, or fungi on inanimate objects and surfaces. In this study, an alternative method is presented using triclosan agents that can kill bacteria and viruses to help keep patient, operating, and emergency rooms free of germs. Samples were treated with triclosan to achieve antimicrobial/antiviral/antifungal properties for further designs to help comfort and bacteria, virus, fungi (BVF) resistantance during use. The physical, and mechanical properties of triclosan treated cotton and cotton/elastane fabrics in comparison with untreated control samples was investigated. The results showed that a small significant decrease was observed for tensile strength (strip and grab methods), tear strength and seam strength. Besides, statistically a small significant decrease was observed with the increase in triclosan concentration for all samples. The panama weaves showed the lowest tensile strength and the highest tear strength and statistically small significant decrease was observed for all treated samples. The antimicrobial tests showed that all treated samples have a very good antimicrobial activity which can also lead to antivirus protection by providing hygienic environment for the users during future designs.

scholarly journals The Influence of Rice Straw on the Physical and Mechanical Properties of Banco, an Adobe Reinforced with Rice Straw

2019 ◽  
Vol 9 (2) ◽  
pp. 2363-2367
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Rice Straw ◽  
Physical And Mechanical Properties ◽  
Mechanical Tests ◽  
High Tensile Strength ◽  
Good Adhesion ◽  
Clay Matrix ◽  
Mechanical Performances

Making adobes with the best mechanical properties for the construction of earthen housings is the overall goal of this work. Specifically, we study the influence of rice straw on the physical and mechanical properties of these adobes. The physical and mechanical properties (compressive and flexural strength) of adobes (mixture of sandy clay and rice straw) have been studied with different proportions of straw in the mixture. It is a question of determining the quantity of stalks of rice straw making it possible to optimize the mechanical performances of the composite. Various compositions have been considered with mass concentrations of rice straw ranging from 0 to 40% relative to the volume of clay sand to make 4×4×16cm prismatic specimens. The results obtained during physical and mechanical tests were presented in the form of a graph. The analysis of these data shows that the optimal addition of rice straw in the clay matrix is 25% for a better compromise between the compressive and tensile strengths. The improvement of the physical and mechanical properties of adobes is related to the good adhesion between the rice straw and the clay matrix, to the high tensile strength of the rice straw and finally to a good distribution of cracks in the composites

scholarly journals Preparation and Characterization of Modified Natural Rubber Blends For Water Purification Treatment Usage

2020 ◽  
Author(s):  
Ruogu Tang ◽  
Wenfa Dong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Relative Volume ◽  
Curing Time ◽  
Water Industry ◽  
High Modulus ◽  
Elongation At Break ◽  
Tear Strength ◽  
Rubber Blends

<div>The water industry used NR was selected for blending with SBR. A series of NR/SBR vulcanizates were prepared through three different vulcanization systems, conventional vulcanization (CV), effective vulcanization (EV) and semi-effective vulcanization (SEV) respectively, basing on each formulation and optimum curing time. We examined the mechanical properties of NR/SBR vulcanizates including tensile strength, tear strength, elongation at break, modulus, Shore A hardnessand and relative volume abrasion. The results indicated that NR/SBR vulcanizates prepared in different systems differed in mechanical properties. Vulcanizates prepared via CV showed higher tensile and tear strength; vulcanizates prepared via EV had high modulus and hardness, and vulcanizates prepared via SEV performed high abrasion resistance. </div>

Preparation and characterization of biodegradable blends of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) and poly(butylene adipate-co-terephthalate)

2016 ◽  
Vol 36 (5) ◽  
pp. 473-480 ◽  
Author(s):  
Min Zhang ◽  
Xiaoqian Diao ◽  
Yujuan Jin ◽  
Yunxuan Weng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Crystallization Temperature ◽  
Molecular Interaction ◽  
Mechanical And Thermal Properties ◽  
Elongation At Break ◽  
Tear Strength ◽  
Biodegradable Blends

Abstract Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH) was blended with poly(butylene adipate-co-terephthalate) (PBAT) by extrusion at different weight ratios (PHBH/PBAT: 100:0, 80:20, 60:40, 50:50, 40:60, 20:80 and 0:100). Films were then prepared from the blends and characterized in terms of their morphological, rheological, mechanical and thermal properties. The morphological and rheological results indicated that PHBH/PBAT blends are immiscible but exhibit possible molecular interaction. The crystallization temperature of PHBH in the blends decreased, indicating that the addition of PBAT inhibited the crystallization of PHBH. Blending PBAT with PHBH improved the processability compared with that of pure polymers. The mechanical properties, including tensile strength, elongation at break and tear strength, increased with increasing PBAT content. The PHBH/PBAT 20:80 blend exhibited significantly improved mechanical properties, which was due to the reinforcing and toughening effect of the finely dispersed PHBH phase.

scholarly journals Preparation and Characterization of Modified Natural Rubber Blends For Water Purification Treatment Usage

2020 ◽  
Author(s):  
Ruogu Tang ◽  
Wenfa Dong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Relative Volume ◽  
Curing Time ◽  
Water Industry ◽  
High Modulus ◽  
Elongation At Break ◽  
Tear Strength ◽  
Rubber Blends

<div>The water industry used NR was selected for blending with SBR. A series of NR/SBR vulcanizates were prepared through three different vulcanization systems, conventional vulcanization (CV), effective vulcanization (EV) and semi-effective vulcanization (SEV) respectively, basing on each formulation and optimum curing time. We examined the mechanical properties of NR/SBR vulcanizates including tensile strength, tear strength, elongation at break, modulus, Shore A hardnessand and relative volume abrasion. The results indicated that NR/SBR vulcanizates prepared in different systems differed in mechanical properties. Vulcanizates prepared via CV showed higher tensile and tear strength; vulcanizates prepared via EV had high modulus and hardness, and vulcanizates prepared via SEV performed high abrasion resistance. </div>

PREPARATION AND CHARACTERIZATION OF REPROCESSED COMPOSITES OF POLYPROPYLENE REINFORCED BY WOOD FIBERS: PHYSICAL AND MECHANICAL PROPERTIES

2017 ◽  
Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Fibers

Fabrication and Characterization of Biocomposite Using Grewia Optiva Fibre (i.e. Bhimal) Reinforced Polyvinyl Alcohol (PVA)

2015 ◽  
Vol 1105 ◽  
pp. 51-55 ◽  
Author(s):  
K.M. Gupta ◽  
Kishor Kalauni
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Fibre ◽  
Fabrication Method ◽  
View Point ◽  
Engineering Material ◽  
Fibre Composites ◽  
Grewia Optiva ◽  
Fabrication And Characterization

Bhimal fibres are quite a newer kind of bio-degradable fibres. They have never been heard before in literatures from the view point of their utility as engineering material. These fibres have been utilized for investigation of their properties. Characterization of this fibre is essential to determine its properties for further use as reinforcing fibre in polymeric, bio-degradable and other kinds of matrix. With this objective, the fabrication method and other mechanical properties of Bhimal-reinforced-PVA biocomposite have been discussed. The stress-strain curves and load-deflection characteristics are obtained. The tensile, compressive, flexure and impact strengths have been calculated. The results are shown in tables and graphs. The results obtained are compared with other existing natural fibre biocomposites. From the observations, it has been concluded that the tensile strength of Bhimal-reinforced-PVA biocomposite is higher than other natural fibre composites. Hence these can be used as reinforcement to produce much lighter weight biocomposites.

scholarly journals Damage Evolution of Granodiorite after Heating and Cooling Treatments

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 779
Author(s):  
Mohamed Gomah ◽  
Guichen Li ◽  
Salah Bader ◽  
Mohamed Elkarmoty ◽  
Mohamed Ismael
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Failure Mode ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Physical Parameters ◽  
Slow Cooling ◽  
Heating And Cooling ◽  
Natural Rock ◽  
The Impact

The awareness of the impact of high temperatures on rock properties is essential to the design of deep geotechnical applications. The purpose of this research is to assess the influence of heating and cooling treatments on the physical and mechanical properties of Egyptian granodiorite as a degrading factor. The samples were heated to various temperatures (200, 400, 600, and 800 °C) and then cooled at different rates, either slowly cooled in the oven and air or quickly cooled in water. The porosity, water absorption, P-wave velocity, tensile strength, failure mode, and associated microstructural alterations due to thermal effect have been studied. The study revealed that the granodiorite has a slight drop in tensile strength, up to 400 °C, for slow cooling routes and that most of the physical attributes are comparable to natural rock. Despite this, granodiorite thermal deterioration is substantially higher for quick cooling than for slow cooling. Between 400:600 °C is ‘the transitional stage’, where the physical and mechanical characteristics degraded exponentially for all cooling pathways. Independent of the cooling method, the granodiorite showed a ductile failure mode associated with reduced peak tensile strengths. Additionally, the microstructure altered from predominantly intergranular cracking to more trans-granular cracking at 600 °C. The integrity of the granodiorite structure was compromised at 800 °C, the physical parameters deteriorated, and the rock tensile strength was negligible. In this research, the temperatures of 400, 600, and 800 °C were remarked to be typical of three divergent phases of granodiorite mechanical and physical properties evolution. Furthermore, 400 °C could be considered as the threshold limit for Egyptian granodiorite physical and mechanical properties for typical thermal underground applications.

scholarly journals Thermal, Physical and Mechanical Properties of Poly(Butylene Succinate)/Kenaf Core Fibers Composites Reinforced with Esterified Lignin

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2359
Author(s):  
Harmaen Ahmad Saffian ◽  
Masayuki Yamaguchi ◽  
Hidayah Ariffin ◽  
Khalina Abdan ◽  
Nur Kartinee Kassim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Loss Modulus ◽  
Physical And Mechanical Properties ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Esterification Reaction ◽  
Butylene Succinate ◽  
Kenaf Core ◽  
Modified Lignin

In this study, Kraft lignin was esterified with phthalic anhydride and was served as reinforcing filler for poly(butylene succinate) (PBS). Composites with different ratios of PBS, lignin (L), modified lignin (ML) and kenaf core fibers (KCF) were fabricated using a compounding method. The fabricated PBS composites and its counterparts were tested for thermal, physical and mechanical properties. Weight percent gain of 4.5% after lignin modification and the FTIR spectra has confirmed the occurrence of an esterification reaction. Better thermo-mechanical properties were observed in the PBS composites reinforced with modified lignin and KCF, as higher storage modulus and loss modulus were recorded using dynamic mechanical analysis. The density of the composites fabricated ranged from 1.26 to 1.43 g/cm3. Water absorption of the composites with the addition of modified lignin is higher than that of composites with unmodified lignin. Pure PBS exhibited the highest tensile strength of 18.62 MPa. Incorporation of lignin and KCF into PBS resulted in different extents of reduction in tensile strength (15.78 to 18.60 MPa). However, PBS composite reinforced with modified lignin exhibited better tensile and flexural strength compared to its unmodified lignin counterpart. PBS composite reinforced with 30 wt% ML and 20 wt% KCF had the highest Izod impact, as fibers could diverge the cracking propagation of the matrix. The thermal conductivity value of the composites ranged from 0.0903 to 0.0983 W/mK, showing great potential as a heat insulator.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

Sign in / Sign up

Export Citation Format

Share Document