Effect of Process Parameters on Cutting Forces and Surface Roughness in Machining of DSS 2205 Using Taguchi’s Approach

2019 ◽  
Vol 895 ◽  
pp. 26-31
Author(s):  
R. Suresh ◽  
L. Shivaramu ◽  
N.G. Siddesh Kumar ◽  
T.N. Srikantha Dath
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Material Behavior ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Coated Carbide ◽  
Side Flow

In the present study an attempt has been made to investigate the effect of process parameters on surface roughness and cutting forces generation in machining of Duplex Stainless Steel (DSS 2205) grade material with TiN coated carbide tool. Taguchi technique is used for optimizing the process parameters. L27 orthogonal array was used to conduct the experimental trials. Cutting forces recorded using piezo-electric based mill tool dynamometer and surface roughness measured using surface roughness measuring instrument. The obtained results indicated that the cutting force increases with increase in feed rate and depth of cut whereas cutting forces decreases with increase in cutting speed. Surface roughness decreases with increase in cutting speed and low feed rate. Scanning Electroscope Microscopic (SEM) images indicates the feed marks, undeformed material and patches on the machined surface. The formation of material side flow and burrs on the feed marks ridges observed at higher cutting speed, low feed rate and depth of cut. It is mainly due to the material behavior like elastic-plastic deformation of the surface layer. The material side flow causes the considerable deterioration of surface quality of the DSS 2205 steel.

Surface Intergrity of Inconel 718 under MQL Condition

2010 ◽  
Vol 150-151 ◽  
pp. 1667-1672 ◽  
Author(s):  
Che Hassan Che Haron ◽  
Jaharah Abd Ghani ◽  
Mohd Shahir Kasim ◽  
T.K. Soon ◽  
Gusri Akhyar Ibrahim ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Machining Process ◽  
Graphical Form ◽  
Depth Of Cut ◽  
Optimum Process ◽  
Machined Surface ◽  
Coated Carbide

The purpose of this study is to investigate the effect of turning parameters on the surface integrity of Inconel 718. The turning parameters studied were cutting speed of 90, 120, 150 m/min, feed rate of 0.15, 0.25, 0.25mm/rev and depth of cut of 0.3, 0.4, 0.5 mm under minimum quantity lubricant (MQL) using coated carbide tool. surface response methodology (RSM) design of experiment using Box-Behnken approach has been employed consisting of various combination of turning parameters Surface roughness, surface topography, microstructure and the micro hardness of the machined surface were studied after the machining process. Feed rate was found to be the most significant parameter affecting the surface roughness. The optimum parameter was obtained with Ra equal to 0.243 µm at cutting speed of 150 m/min, feed rate of 0.25 mm/rev and depth of cut of 0.3mm. A mathematical model for surface roughness was developed using Response Surface Methodology. The effect of turning parameters and factor interactions on surface roughness is presented in 3D graphical form, which helps in selecting the optimum process parameters to achieve the desired surface quality.

Experimental investigations of cutting parameters’ influence on cutting forces and surface roughness in turning of Inconel alloy X-750 with biodegradable vegetable oil

2015 ◽  
Vol 231 (9) ◽  
pp. 1516-1527 ◽  
Author(s):  
Ahmadreza Hosseini Tazehkandi ◽  
Mohammadreza Shabgard ◽  
Farid Pilehvarian ◽  
Nakisa Farshfroush
Keyword(s):  
Surface Roughness ◽  
Vegetable Oil ◽  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Inconel Alloy ◽  
Coated Carbide

Nickel-based Inconel X-750 superalloy is widely applied in aerospace industry and manufacturing of gas turbine blades, power generators and heat exchangers due to its exclusive properties. As a consequence of low heat transfer coefficient and work-hardening properties, this alloy is known as a poorly machinable alloy. In this work, effect of machining parameters (cutting speed, feed rate and depth of cut) on cutting forces and surface roughness was investigated during turning of Inconel alloy X-750 with coated carbide tool. In order to meet the demands of the environment-friendly cutting processes and human health, biodegradable vegetable oil (BioCut 4600) was selected as the cutting fluid. The results were analyzed using response surface methodology and statistical analysis of variance, and mathematical models for cutting forces and surface roughness were proposed. Results indicated that feed rate and cutting speed were the most effective parameters on the surface roughness. However, depth of cut was the most effective parameter on cutting forces in comparison with cutting speed and feed rate. Eventually, in order to achieve the main aims of industrial production in large amounts and green manufacturing, the ranges for the best cutting conditions were presented.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

scholarly journals Analysis and Optimization of Cutting Tool Coating Effects on Surface Roughness and Cutting Forces on Turning of AA 6061 Alloy

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Mahir Akgün ◽  
Fuat Kara
Keyword(s):  
Surface Roughness ◽  
Mathematical Models ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Machined Surface ◽  
Tool Coating ◽  
Cutting Inserts

The present work has been focused on cutting force (Fc) and analysis of machined surface in turning of AA 6061 alloy with uncoated and PVD-TiB2 coated cutting inserts. Turning tests have been conducted on a CNC turning under dry cutting conditions based on Taguchi L18 (21 × 33) array. Kistler 9257A type dynamometer and equipment have been used in measuring the main cutting force (Fc) in turning experiments. Analysis of variance (ANOVA) has been applied to define the effect levels of the turning parameters on Fc and Ra. Moreover, the mathematical models for Fc and Ra have been developed via linear and quadratic regression models. The results indicated that the best performance in terms of Fc and Ra was obtained at an uncoated insert, cutting speed of 350 m/min, feed rate of 0.1 mm/rev, and depth of cut of 1 mm. Moreover, the feed rate is the most influential parameter on Ra and Fc, with 64.28% and 54.9%, respectively. The developed mathematical models for cutting force (Fc) and surface roughness (Ra) present reliable results with coefficients of determination (R2) of 96.04% and 92.15%, respectively.

Wear Performance of The Zirconia Toughened Alumina Added With TiO2 and Cr2O3 Ceramic Cutting Tool

2021 ◽  
Author(s):  
Raqibah Najwa Mudzaffar ◽  
Mohamad Faiz Izzat Bahauddin ◽  
Hanisah Manshor ◽  
Ahmad Zahirani Ahmad Azhar ◽  
Nik Akmar Rejab ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Crater Wear ◽  
Machined Surface ◽  
Ceramic Cutting Tool ◽  
Zirconia Toughened Alumina

Abstract The zirconia toughened alumina enhanced with titania and chromia (ZTA-TiO2-Cr2O3) ceramic cutting tool is a new cutting tool that possesses good hardness and fracture toughness. However, the performance of the ZTA-TiO2-Cr2O3 cutting tool continues to remain unknown and therefore requires further study. In this research, the wearing of the ZTA-TiO2-Cr2O3 cutting tool and the surface roughness of the machined surface of stainless steel 316L was investigated. The experiments were conducted where the cutting speeds range between 314 to 455 m/min, a feed rate from 0.1 to 0.15 mm/rev, and a depth of cut of 0.2 mm. A CNC lathe machine was utilised to conduct the turning operation for the experiment. Additionally, analysis of the flank wear and crater wear was undertaken using an optical microscope, while the chipping area was observed via scanning electron microscopy (SEM). The surface roughness of the machined surface was measured via portable surface roughness. The lowest value of flank wear, crater wear and surface roughness obtained are 0.044 mm, 0.45 mm2, and 0.50 µm, respectively at the highest cutting speed of 455 m/min and the highest feed rate of 0.15 mm/rev. The chipping area became smaller with the increase of feed rate from 0.10 to 0.15 mm/rev and larger when the feed rate decrease. This was due to the reduced vibrations at the higher spindle speed resulting in a more stable cutting operation, thereby reducing the value of tool wear, surface roughness, and the chipping area.

Machining Apprenticeship Based on Experimental Training Practice

2011 ◽  
Vol 692 ◽  
pp. 83-92
Author(s):  
Pedro Jose Arrazola ◽  
A. Villar ◽  
R. Fernández ◽  
J. Aperribay
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Feed Rate ◽  
Cutting Forces ◽  
Theoretical Calculations ◽  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Practical Training ◽  
Input Parameters

This article describes a practical machining training aiming that the students acquire the theoretical-practical knowledge of chip formation process. The training takes place after theoretical lessons of machining processes. Thus, this practice allows strengthening the knowledge gained during the lessons. The practical training lasts for five hours, and the student assisted by the teacher analyses the influence of some machining entry parameters (cutting speed, feed rate...) on exit parameters like: (I) cutting forces and power consumption, (II) surface roughness, and (III) chip typology. The practical session is carried out on an experimental set-up (Lathe CNC Danobar 65) equipped with sensors and devices to measure forces (sensor Kistler 9121) and power consumption. In addition, a portable rugosimeter (Hommelwerke) is employed to perform surface roughness measurements. No especial devices are needed for the chip typology analysis. In the case of cutting forces and power consumption, the following input parameters influences are analysed: feed rate, depth of cut and cutting speed. In the case of surface roughness analysis, the following input parameters influences are analysed: feed rate and nose radius of the cutting insert. Finally, regarding chip typology feed rate and depth of cut are examined. The experimental results are compared with model predictions (theoretical calculations) for the three issues studied. The students have to compare both results: theoretical an empirical and they need to explain the reasons when discrepancies appear. Results obtained during the last years demonstrate the student acquires better knowledge of the machining process, and at the same time realises of the process complexity.

The Effect of Vortex Tube Cooling on Surface Roughness and Carbon Footprint in Dry Turning

2014 ◽  
Vol 903 ◽  
pp. 135-138
Author(s):  
Zahari Taha ◽  
Hadi Abdul Salaam ◽  
Phoon Sin Ye ◽  
Tuan Muhammad Yusoff Shah Tuan Ya
Keyword(s):  
Surface Roughness ◽  
Carbon Footprint ◽  
Feed Rate ◽  
Vortex Tube ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Air Cooling ◽  
Coated Carbide

This paper presents a study on the effect of Ranque-Hilsch vortex tube air cooling on surface roughness quality and carbon footprint when turning mild steel workpiece with coated carbide cutting tool. The cutting parameters involved in this study were cutting speed, feed rate and depth of cut. The cutting speed and feed rate were fixed at 160 m/min and 0.10, 0.18 and 0.28 mm/rev, while the depth of cut was varied from 1.0 to 4.0 mm. During the turning process, the cutting temperatures were measured using infrared thermometer and the power consumption was measured using a power and harmonics analyzer and then converted into carbon footprint. The machined parts surface roughness were measured using a surface roughness tester. The results show that machining with Ranque - Hilsch vortex tube reduces the cutting temperature, but the surface roughness and carbon footprint is better under ambient condition except at a higher feedrate.

The Effect of Vortex Tube Air Cooling on Surface Roughness and Power Consumption in Dry Turning

2013 ◽  
Vol 310 ◽  
pp. 348-351 ◽  
Author(s):  
Hadi Abdul Salaam ◽  
Phoon Sin Ye ◽  
Zahari Taha ◽  
Tuan Muhammad Yusoff Shah Tuan Ya
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Feed Rate ◽  
Vortex Tube ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Air Cooling ◽  
Coated Carbide

This paper presents a study of the effect of Ranque-Hilsch vortex tube air cooling on surface roughness quality and power consumption when turning mild steel material with coated carbide cutting tool. The cutting parameters involved in this study were cutting speed, feed rate and depth of cut. The cutting speed and feed rate were fixed at 160 m/min and 0.28 mm/rev, while the depth of cut was varied from 1.0 to 4.0 mm. During the turning process, the cutting temperatures were measured using an infrared thermometer and the power consumption was measured using a power and harmonics analyzer. The machined parts surface roughnesses were measured using a surface roughness tester. The results show that cooling using the Ranque-Hilsch vortex tube air cooling reduces the cutting temperature and the power consumption, but the surface roughness results is better when cooling with environment air.

scholarly journals Machinability Investigations on Aerospace Custom 450 Alloy Using TiAlN/TiCN, TiCN/TiAlN Coated and Uncoated Carbide Tools

2021 ◽  
Vol 54 (2) ◽  
pp. 325-334
Author(s):  
Sampath Kumar Thepperumal ◽  
Vignesh Margabandu ◽  
Ramanujam Radhakrishnan ◽  
John Rajan Amaladas ◽  
Shri Vignesh Ananthakrishnan
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Feed Rate ◽  
Cutting Speed ◽  
Optimal Level ◽  
Depth Of Cut ◽  
Electron Microscopic ◽  
Utility Concept ◽  
Coated Tool ◽  
Coated Carbide

In this present research, the machinability studies of TiAlN/TiCN, TiCN/TiAlN coated and uncoated inserts were investigated on machining custom 450 alloy. The machining input parameters such as feed rate (f), cutting speed (V) and depth of cut (d) are set using orthogonal array. The machining output parameters such as surface roughness, tool wear and cutting forces were studied for its parametric contribution and it was analyzed using Analysis of Variance (ANOVA). Further, the tool wear obtained was studied using scanning electron microscopic images and energy dispersive spectroscopy analysis was conducted to check the addition of work material elements to the coated tool surface. The results show that, the feed rate is the most contributing factor in deciding resultant forces, surface roughness and tool wear respectively. TiAlN/TiCN coated carbide tool has obtained improved machinability, when compared to TiCN/TiAlN coated carbide and uncoated carbide inserts. To obtain one optimal level for all three responses of three types of tools, multi criteria decision making approach, named utility concept approach is selected. Based on the MCDM analysis, it is found that trial number 4 gives better experimental output of improved surface integrity, lower resultant force and less tool wear for all types of tools.

scholarly journals An Investigation on Optimum Process Parameters in Terms of Surface Roughness for Turning Titanium Alloy Ti-6Al-4V Using Coated Carbide

2019 ◽  
Vol 4 (4) ◽  
pp. 137-145
Author(s):  
Abdul Md Mazid ◽  
Md. Shahanur Hasan ◽  
Kazi Badrul Ahsan
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Real Life ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Ti Alloys ◽  
Machined Parts ◽  
Coated Carbide ◽  
Coated Carbide Tools

The quality of machined parts and the productivity of machining that leads to economic sustainability.  These factors are also vital for machinability improvement for materials, as well as, for economically sustainable manufacturing. Due to their poor machinability titanium alloys (Ti-alloys) are categorised as difficult-to-machine materials. For the same reason products made of Ti-alloys are highly expensive and are used only in strategic and sophisticated industries.  A series of real-life experimental investigations was carried out to reveal the economic optimal zones of machining parameters that can produce the best possible surface roughness in machining Ti-6Al-4V alloy, using the coated carbide cutting tools, in shortest period of operation time. As the output of the research, for using the coated carbide tools for machining the investigated Ti-alloy, optimal zones of cutting speed, feed rate and depth of cut have been proposed and presented in graphical format. The current research revealed that all three groups (with nose radius Nr = 0.4, 0.8, and 1.2 mm) of coated carbide tools are capable to produce best surface finish, ranging between Ra = 0.5 - 1.0 µm, with cutting speed starting at V = 60 m/min and beyond at least up to V = 250 m/min while keeping the feed rate and depth of cut as constants as f = 0.1 mm/rev and d = 0.5 mm. The data on the graphs may help researchers, engineers and manufacturers to select optimal economic cutting speed, feed rate and depth of cut to achieve a certain level of surface roughness of machined components as assigned by the product designer on the part drawing. This reduces the production cost substantially, reduces number of defect products and improves product quality for machined parts.

Sign in / Sign up

Export Citation Format

Share Document