Wear Performance of The Zirconia Toughened Alumina Added With TiO2 and Cr2O3 Ceramic Cutting Tool

2021 ◽  
Author(s):  
Raqibah Najwa Mudzaffar ◽  
Mohamad Faiz Izzat Bahauddin ◽  
Hanisah Manshor ◽  
Ahmad Zahirani Ahmad Azhar ◽  
Nik Akmar Rejab ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Crater Wear ◽  
Machined Surface ◽  
Ceramic Cutting Tool ◽  
Zirconia Toughened Alumina

Abstract The zirconia toughened alumina enhanced with titania and chromia (ZTA-TiO2-Cr2O3) ceramic cutting tool is a new cutting tool that possesses good hardness and fracture toughness. However, the performance of the ZTA-TiO2-Cr2O3 cutting tool continues to remain unknown and therefore requires further study. In this research, the wearing of the ZTA-TiO2-Cr2O3 cutting tool and the surface roughness of the machined surface of stainless steel 316L was investigated. The experiments were conducted where the cutting speeds range between 314 to 455 m/min, a feed rate from 0.1 to 0.15 mm/rev, and a depth of cut of 0.2 mm. A CNC lathe machine was utilised to conduct the turning operation for the experiment. Additionally, analysis of the flank wear and crater wear was undertaken using an optical microscope, while the chipping area was observed via scanning electron microscopy (SEM). The surface roughness of the machined surface was measured via portable surface roughness. The lowest value of flank wear, crater wear and surface roughness obtained are 0.044 mm, 0.45 mm2, and 0.50 µm, respectively at the highest cutting speed of 455 m/min and the highest feed rate of 0.15 mm/rev. The chipping area became smaller with the increase of feed rate from 0.10 to 0.15 mm/rev and larger when the feed rate decrease. This was due to the reduced vibrations at the higher spindle speed resulting in a more stable cutting operation, thereby reducing the value of tool wear, surface roughness, and the chipping area.

Effects of Cutting Speed and Feed Rate on Surface Roughness in Hard Turning of AISI 4140 with Mixed Ceramic Cutting Tool

2018 ◽  
Vol 779 ◽  
pp. 153-158
Author(s):  
Phacharadit Paengchit ◽  
Charnnarong Saikaew
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Hard Turning ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Machined Surface ◽  
Data Set ◽  
Ceramic Cutting Tool ◽  
Aisi 4140 ◽  
Mixed Ceramic

This work investigated the influences of cutting speed and feed rate on surface roughness in hard turning of AISI 4140 chromium molybdenum steel bar using mixed ceramic inserts Al2O3+TiC under dry condition for automotive industry applications. Turning experiments were conducted by varying cutting speed ranging from 150 to 220 m/min and feed rate ranging from 0.06 to 1 mm/rev. General factorial design was used to analyze the data set of surface roughness and determine statistically significant process factors based on analysis of variance results. The results showed that average surface roughness was significantly affected by feed rate and interaction between cutting speed and feed rate at the level of significance of 0.05. An optimal operating condition for hard turning of AISI 4140 with the ceramic cutting tool that produced a minimum machined surface roughness was obtained at cutting speed of 220 m/min and 0.06 mm/rev.

scholarly journals Experimental Study on Surface Roughness and Flank Wear in Turning of Nimonic C263 under Dry Cutting Conditions

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
J. Francis Xavier ◽  
B. Ravi ◽  
D. Jayabalakrishnan ◽  
Chakaravarthy Ezilarasan ◽  
V. Jayaseelan ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Feed Rate ◽  
Flank Wear ◽  
Cutting Speed ◽  
Controlling Factors ◽  
Average Error ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Machined Surface

Aircraft component manufacturing sector is looking for high precision machining in aircraft components. The present work explores the operability of green manufacturing of Nimonic C263 using dry turning. Nimonic C263 is tough to turn owing to its inherent quality like low conductivity and more work hardening. Therefore, in order to improve this machined surface/integrity, the controlling factors were optimized based on desirability approach for minimum of surface roughness and flank wear during turning of this alloy using CBN insert. L27 orthogonal array was chosen to carry out the experiment. The effects of controlling factors, such as cutting speed ( V ), feed rate ( S ), and cut penetration/depth of cut ( a p ) on the outputs, were also explored. The feed rate was a major impact to affect surface finish and flank wear. The average error percentage between the experimental and RSM models for surface finish was 4.76 percent and 2.79 percent for flank wear.

scholarly journals Surface Roughness Values of Magnesium Alloy AZ31 When Turning by Using Rotary Cutting Tool

INSIST ◽  
2016 ◽  
Vol 1 (1) ◽  
pp. 54
Author(s):  
Gusri Akhyar ◽  
Suryadiwansa Harun ◽  
Arinal Hamni
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Feed Rate ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Work Piece ◽  
Machined Surface ◽  
Rotary Cutting

Abstract - Magnesium and magnesium alloys is one of materials that worldwide used on automotive components due to very good  strength to weight ratio, resistant to corrosion, lighter compare to steel materials. Other than that magnesium has an advantage in easy to form and good machinability.  Nevertheless, magnesium known as metal which is easy to burned because of magnesium has low melting point. To maintain magnesium from burning quickly when proses machining, it needs to use coolant or lubricant to reduce temperature. Using of coolant when machining process can reduce temperature on cutting tool and work piece material, while using of lubricant can reduce friction between the cutting tool and work piece mateial. However, using of coolant and lubricant can harm for the environment and also coolant difficult to destroyed. Therefore, an alternative method to reduce the temperature when machining of magnesium alloy is using  the rotary cutting tool system. In the rotary cutting tool system, the cutting tool has a time to experience cooling in the period time. Other than aspect of temperature, surface roughness values are representative of surface of quality of produced componens. In this research, surface roughness value of magnesium alloy of AZ31 observed in ranges of work piece cutting speed of  (Vw) 25, 50, 120, 160, 200 m/min, rotary cutting speed of (Vt) 25, 50, 75 m/min, feed rate of (f) 0,05  and 0,10 mm/rev, and depth of cut of 0.2 mm. The turning process was done by using two kinds of diameter of rotary cutting tools are 16 and 20 mm, and without applying of coolant. The results of the research showed that the minimum surface roughness value of machined surface was 0,62𝝻m by using insert with diameter of 16 mm, while the maximum surface roughness value of machined surface was 2,86 𝝻m by using insert with diameter of 20 mm. This result stated that the increase in the diameter of rotary cutting tool gives a significant effect on the produced surface roughness value. Factor of feed rate also gives a significant contribution on the surface roughness value of machined magnesium surface.  The increase in feed rate generated significantly surface roughness value as long as the trials experiments. The produced surface roughness values inversely proportional to the cutting speed of rotary cutting tool.Keywords - magnesium, rotary tool, surface roughness, turning. 

Optimization of Surface Roughness by Using Different Cutting Tools for Aluminum Alloy 6063

2020 ◽  
Vol 17 (2) ◽  
pp. 961-966
Author(s):  
Allina Abdullah ◽  
Afiqah Azman ◽  
B. M. Khirulrizwan
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Optimum Condition ◽  
Feed Rate ◽  
Optimum Parameter ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Numerical Control ◽  
Depth Of Cut

This research outlines an experimental study to determine the optimum parameter of cutting tool for the best surface roughness (Ra) of Aluminum Alloy (AA) 6063. For the experiment in this research, cutting parameters such as cutting speed, depth of cut and feed rate are used to identify the effect of both cutting tools which are tungsten carbide and cermet towards the surface roughness (Ra) of material AA6063. The machining operation involved to cut the material is turning process by using Computer Numerical Control (CNC) Lathe machine. The experimental design was designed by Full Factorial. The experiment that had been conducted by the researcher is 33 with 2 replications. The total number of the experiments that had been run is 54 runs for each cutting tool. Thus, the total number of experiments for both cutting tools is 108 runs. ANOVA analysis had been analyzed to identify the significant factor that affect the Ra result. The significant factors that affect the Ra result of AA6063 are feed rate and cutting speed. The researcher used main effect plot to determine the factor that most influenced the surface roughness of AA6063, the optimum condition of surface roughness and the optimum parameter of cutting tool. The factor that most influenced the surface roughness of AA6063 is feed rate. The optimum condition of surface roughness is at the feed rate of 0.05 mm/rev, cutting speed of 600 rpm and depth of cut of 0.10 mm. While the optimum parameter of cutting tool is cermet insert with the lowest value of surface roughness (Ra) result which is 0.650 μm.

scholarly journals Investigate the Effect of Cutting Parameters on Surface Roughness When Milling X12m Steel

2021 ◽  
pp. 258-263
Author(s):  
Do Thi Kim Lien ◽  
Nguyen Dinh Man ◽  
Phung Tran Dinh
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Negligible Effect ◽  
Depth Of Cut ◽  
The Relationship

In this paper, an experimental study on the effect of cutting parameters on surface roughness was conducted when milling X12M steel. The cutting tool used in this study is a face milling cutter. The material that is used to make the insert is the hard alloy T15K6. The cutting parameters covered in this study include the cutting speed, the feed rate and depth of cut. The experiments are performed in the form of a rotating center composite design. The analysis shows that for both Ra and Rz: (1) the feed rate has the greatest influence on the surface roughness while the depth of cut, the cutting speed has a negligible effect on the surface roughness. (2) only the interaction between the feed rate and the depth of the cut has a significant effect on both Ra and Rz while the interaction between the cutting speed and the feed rate, the interaction between the cutting speed and the depth of cut have a negligible effect on surface roughness. A regression equation showing the relationship between Ra, Rz, and cutting parameters has also been built in this study.

scholarly journals Analysis and Optimization of Ceramic Cutting Tool In Hard Turning of EN-31 Using Factorial Design

2012 ◽  
pp. 53-58
Author(s):  
Chetan Darshan ◽  
Lakhvir Singh ◽  
APS Sethi
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Analysis Of Variance ◽  
Feed Rate ◽  
Hard Turning ◽  
Flank Wear ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Good Surface ◽  
En 31

Manufacturers around the globe persistently looking for the cheapest and quality manufactured machined components to compete in the market. Good surface quality is desired for the proper functioning of the produced parts. The surface quality is influenced by cutting speed, feed rate and depth of cut and many other parameters. In the present study attempt has been made to evaluate the performance of ceramic inserts during hard turning of EN-31 steel. The analysis of variance is applied to study the effect of cutting speed, feed rate and depth of cut on Flank wear and surface roughness. Model is found to be statically significant using regression model, while feed and depth of cut are the factor affecting Flank wear and feed is dominating factors for surface roughness. The analysis of variance was used to analyze the input parameters and there interactions during machining. The developed model predicted response factor at 95% confidence level.

scholarly journals Analysis and Optimization of Cutting Tool Coating Effects on Surface Roughness and Cutting Forces on Turning of AA 6061 Alloy

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Mahir Akgün ◽  
Fuat Kara
Keyword(s):  
Surface Roughness ◽  
Mathematical Models ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Machined Surface ◽  
Tool Coating ◽  
Cutting Inserts

The present work has been focused on cutting force (Fc) and analysis of machined surface in turning of AA 6061 alloy with uncoated and PVD-TiB2 coated cutting inserts. Turning tests have been conducted on a CNC turning under dry cutting conditions based on Taguchi L18 (21 × 33) array. Kistler 9257A type dynamometer and equipment have been used in measuring the main cutting force (Fc) in turning experiments. Analysis of variance (ANOVA) has been applied to define the effect levels of the turning parameters on Fc and Ra. Moreover, the mathematical models for Fc and Ra have been developed via linear and quadratic regression models. The results indicated that the best performance in terms of Fc and Ra was obtained at an uncoated insert, cutting speed of 350 m/min, feed rate of 0.1 mm/rev, and depth of cut of 1 mm. Moreover, the feed rate is the most influential parameter on Ra and Fc, with 64.28% and 54.9%, respectively. The developed mathematical models for cutting force (Fc) and surface roughness (Ra) present reliable results with coefficients of determination (R2) of 96.04% and 92.15%, respectively.

scholarly journals Prediction of cutting tool vibration and surface roughness in hard turning of AISI52100 steel

2018 ◽  
Vol 211 ◽  
pp. 03011
Author(s):  
Nitin Ambhore ◽  
Dinesh Kamble ◽  
Satish Chinchanikar
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Vibration Amplitude ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Vibration Signals ◽  
Cutting Parameter ◽  
Acceleration Amplitude

The changing behavior of vibration signals with varying cutting parameters (cutting speed, feed rate and depth of cut) for turning hardened AISI52100 steel has been studied and reported. The vibration response of cutting tool in all three mutually perpendicular directions, namely, in feed Vx, radial Vy and, tangential Vz directions have been captured by mounting piezoelectric tri-axial accelerometer close to the cutting tool. Experiments are planned and conducted as per Central composite rotatable design of Surface response methodology. The second order multiple regression models are developed to correlate cutting parameters with vibration acceleration and surface roughness. The coefficient of regression R2 for all models is found close to 0.92 which shows that the developed models are reliable and provide an excellent explanation between the cutting parameter and the vibration of cutting tool within limits. The analysis of the results revealed that cutting conditions are having prominent and mixed type effect on vibration signals. The acceleration amplitude Vx, Vy and Vz increases with increase in cutting speed, and depth of cut. The vibration amplitude Vx, Vy and Vz initially increases as feed increases and, with further increase in feed, the vibration amplitude decreases. The surface roughness is highly influenced by the feed rate followed by cutting speed whereas the depth of cut was found less significant. The fluctuation in frequency is observed in all directions. However, the band of frequency remains within a certain range. Within selected cutting parameter range, the maximum acceleration amplitude is observed in frequency band of 4 kHz - 16 kHz.

Evaluation of PVD-Inserts Performance and Surface Integrity when Turning Ti-6Al-4V ELI under Dry Machining

2011 ◽  
Vol 264-265 ◽  
pp. 1050-1055 ◽  
Author(s):  
Gusri Akhyar Ibrahim ◽  
Che Hassan Che Haron ◽  
Jaharah Abd. Ghani
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Base Material ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Softening Effect ◽  
Surface Segmentation ◽  
Initial Stage ◽  
Deformed Layer

The great advancement in the development of carbide cutting tool with super-hard coating layers taken place in recent few decades, can improve the performance of cutting tool and machinability of titanium alloy. The turning parameters evaluated are cutting speed (55, 75, 95 m/min), feed rate (0.15, 0.25, 0.35 mm/rev), depth of cut (0.10, 0.15, 0.20 mm) and tool grade of PVD carbide tool. The results that tool life shows patterns of rapidly increase at the initial stage and gradually increased at the second stage and extremely increased at the final stage. The trend lines of surface roughness have are the surface roughness value is high at first machining after that regularly decreases. Work hardening of the deformed layer beneath machined surface caused higher hardness than the average hardness of the base material. However, the softening effect also occurred below the machined surface. Segmentation or serration at the chip edge was caused by high strain and pressure during machining.

Surface Intergrity of Inconel 718 under MQL Condition

2010 ◽  
Vol 150-151 ◽  
pp. 1667-1672 ◽  
Author(s):  
Che Hassan Che Haron ◽  
Jaharah Abd Ghani ◽  
Mohd Shahir Kasim ◽  
T.K. Soon ◽  
Gusri Akhyar Ibrahim ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Machining Process ◽  
Graphical Form ◽  
Depth Of Cut ◽  
Optimum Process ◽  
Machined Surface ◽  
Coated Carbide

The purpose of this study is to investigate the effect of turning parameters on the surface integrity of Inconel 718. The turning parameters studied were cutting speed of 90, 120, 150 m/min, feed rate of 0.15, 0.25, 0.25mm/rev and depth of cut of 0.3, 0.4, 0.5 mm under minimum quantity lubricant (MQL) using coated carbide tool. surface response methodology (RSM) design of experiment using Box-Behnken approach has been employed consisting of various combination of turning parameters Surface roughness, surface topography, microstructure and the micro hardness of the machined surface were studied after the machining process. Feed rate was found to be the most significant parameter affecting the surface roughness. The optimum parameter was obtained with Ra equal to 0.243 µm at cutting speed of 150 m/min, feed rate of 0.25 mm/rev and depth of cut of 0.3mm. A mathematical model for surface roughness was developed using Response Surface Methodology. The effect of turning parameters and factor interactions on surface roughness is presented in 3D graphical form, which helps in selecting the optimum process parameters to achieve the desired surface quality.

Sign in / Sign up

Export Citation Format

Share Document