Study on the Cutting Properties about Magnesium Alloy when Dry Turning with Kentanium Cutting Tools

2010 ◽  
Vol 102-104 ◽  
pp. 653-657 ◽  
Author(s):  
Xu Hong Guo ◽  
Li Jun Teng ◽  
Wei Wang ◽  
Ting Ting Chen
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Tool Wear ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Depth ◽  
Dry Turning ◽  
Main Influence

In recent years, the machinability of magnesium alloy is concerned more and more by the public. In this paper, a study on the cutting properties of magnesium alloy AZ91D when dry turning with kentanium cutting tools is presented. It shows the cutting force measured by a data acquisition system which is made up of Kistler9257B piezoelectric crystal sensor dynamometer, Kistler5070A10100 charge amplifier and computer. The effect of cutting parameters on cutting force was studied, and the experimental formula was built. The tool wear and chip characteristics were observed with KYKY-EM3200 electron scanning microscope and EDAX PV9900 alpha ray spectrometer, while the surface roughness of the workpiece was measured with 2205 profilometer. Results showed that the cutting depth was the main influence factor on cutting force, followed by feed rate and cutting speed . The main form of tool wear showed to be diffusive wear and adhesive wear. The feed rate had the main influence on chip form and the workpiece surface roughness, cutting speed was less effective, the cutting depth was the least.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

Experimental Investigations of Cutting Conditions Influence on Main Cutting Force and Surface Roughness Based on Chip Form Types in Cast Nylon Turning

2011 ◽  
Vol 110-116 ◽  
pp. 3563-3569 ◽  
Author(s):  
Bandit Suksawat
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Causal Effect ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Path Coefficient ◽  
Cutting Depth

This paper aims to investigate cutting conditions influence on main cutting force and surface roughness based on considered chip form types in cast nylon turning operation with single-point high speed steel cutting tool. The 75 experiments were performed by average of three levels of cutting speed, five levels of cutting depth and five levels of feed rate. The results reveal that main cutting forces were increased by an increasing of cutting speed and cutting depth for all obtained chip form types for all chip form types. The surface roughness is affected by increasing of feed rate and reduction of cutting speed for 2.3 Snarled and 4.3 Snarled chip form types. The statistical path-coefficient analysis results are shown that the main cutting force affected by cutting speed, depth of cut and feed rate with total causal effect value of 0.5537, 0.4785 and 0.1718, respectively. The surface roughness is influenced by feed rate, cutting speed and depth of cut with 0.8400, -0.2419 and-0.0711 of total causal effect value, respectively. These results are useful to perform varying cutting conditions for high quality of workpiece in cast nylon turning by control the chip form type.

An Experimental Study on Finish Dry Milling of AISI 321 Stainless Steel

2016 ◽  
Vol 861 ◽  
pp. 26-31 ◽  
Author(s):  
Peng Guo ◽  
Chuan Zhen Huang ◽  
Bin Zou ◽  
Jun Wang ◽  
Han Lian Liu ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Tool Wear ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Milling ◽  
Aisi 321 ◽  
Coated Cemented Carbide

The milling of AISI 321 stainless steel which has wide engineering applications particularly in automobile, aerospace and medicine is of great importance especially in the conditions where high surface quality is required. In this paper, L16 orthogonal array design of experiments was adopted to evaluate the machinability of AISI 321 stainless steel with coated cemented carbide tools under finish dry milling conditions, and the influence of cutting speed ( V ), feed rate ( f ) and depth of cut ( ap ) on cutting force, surface roughness and tool wear was analysed. The experimental results revealed that the cutting force decreased with an increase in the cutting speed and increased with an increase in the feed rate or the depth of cut. The tool wear was affected significantly by the cutting speed and the depth of cut, while the effect of the feed rate on the tool wear was insignificant. With the cutting speed increased up to 160 m/min, a decreasing tendency in the surface roughness was observed, but when the cutting speed was further increased, the surface roughness increased. The effect of the feed rate and the depth of cut on the surface roughness was slight.

scholarly journals Machinability of Luxury Vinyl Tiles during Plain Milling Using a Helical Cutter

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2174 ◽  
Author(s):  
Zhaolong Zhu ◽  
Pingxiang Cao ◽  
Xiaolei Guo ◽  
Xiaodong (Alice) Wang ◽  
Fan Zhang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Helix Angle ◽  
Helical Milling ◽  
Tool Geometry ◽  
Cutting Depth ◽  
Diamond Cutting Tools

In order to better provide a theoretical basis for the machining of luxury vinyl tiles, a helical milling experiment was conducted by using diamond cutting tools, and special attention was given to the trends of cutting force and surface roughness in respect to tool geometry and cutting parameters. The results showed that the resultant force was negatively correlated to the helix angle and cutting speed, but positively correlated with the cutting depth. Then, that the surface roughness increased with a decrease of the helix angle and an increase of cutting depth, while as cutting speed raised, the surface roughness first declined and then increased. Thirdly, the cutting depth was shown to have the greatest influence on both cutting force and surface roughness, followed by helix angle and cutting speed. Fourth, the contribution of cutting depth only was significant to cutting force, while both the helix angle and cutting speed had insignificant influence on the cutting force and surface roughness. Finally, the optimal cutting conditions were proposed for industrial production, in which the helix angle, cutting speed and cutting depth were 70°, 2200 m/min and 0.5 mm, respectively.

scholarly journals Optimization of the Cutting Regime in the Turning of the AISI 316L Steel for Biomedical Purposes Based on the Initial Progression of Tool Wear

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1698
Author(s):  
Ricardo del Risco-Alfonso ◽  
Roberto Pérez-Rodríguez ◽  
Patricia del Carmen Zambrano Robledo ◽  
Marcelino Rivas Santana ◽  
Ramón Quiza
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Force ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Nsga Ii ◽  
Input Variables ◽  
Aisi 316 L

The development of biomedical devices has improved the quality of life for millions of people. The increase in life expectancy generates an increase in the demand for these devices. One of the most used materials for these purposes is 316 L austenitic stainless steel due to its mechanical properties and good biocompatibility. The objective of the present investigation was to identify the dependence between the main cutting force, the initial speed of the tool wear, the surface roughness, and the parameters of the cutting regime. Based on these dependencies, a multi-objective optimization model is proposed to minimize the energy consumed and initial wear rate, as well as to maximize productivity, maintaining the surface roughness values below those established by the ISO 5832-1 standard. The wear of the cutting tool was measured on a scanning electron microscope. For the optimization process, a genetic algorithm based on NSGA-II (Non-nominated Sorting Genetic Algorithm) was implemented. The input variables were the cutting speed and the feed in three levels. The cutting force and surface roughness were set as restrictions. It is concluded that the mathematical model allows for the optimization of the cutting regime during dry turning and with the use of MQL (Minimum Quantity Lubrication) with BIDEMICS JX1 ceramic tools (NTK Cutting Tools, Wixom, MI, USA), of AISI 316 L steel for biomedical purposes. Pareto sets and boundaries allow for choosing the most appropriate solution according to the specific conditions of the workshop where it is applied, minimizing the initial progression of tool wear and energy consumed, and maximizing productivity by guaranteeing the surface roughness values established for these types of parts according to the standard.

Effect of Tool Wear on Tool Life and Surface Finish when Machining DF-3 Hardened Tool Steel

2013 ◽  
Vol 315 ◽  
pp. 241-245 ◽  
Author(s):  
Ali Davoudinejad ◽  
M.Y. Noordin ◽  
Danial Ghodsiyeh ◽  
Sina Alizadeh Ashrafi ◽  
Mohsen Marani Barzani
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Tool Life ◽  
Tool Steel ◽  
Wear Mechanism ◽  
Feed Rate ◽  
Hard Turning ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Mixed Ceramic

Hard turning is a dominant machining operation performed on hardened materials using single-point cutting tools. In recent years, hard turning operation has become more and more capable with respect to various machinability criteria. This work deals with machinability of hardened DF-3 tool steel with 55 ±1 HRC hardness at various cutting conditions in terms of tool life, tool wear mechanism and surface roughness. Continuous dry turning tests were carried out using coated, mixed ceramic insert with honed edge geometry. Two different cutting speeds, 100 and 210 m/min, and feed rate values of 0.05, 0.125 and 0.2 mm/rev were used with a 0.2 mm constant depth of cut for all tests. Additionally scanning electron microscope (SEM) was employed to clarify the different types of wear. As far as tool life was concerned, best result was achieved at lowest cutting condition whereas surface roughness values decreased when operating at higher cutting speed and lower feed rate. Additionally maximum volume of material removed is obtained at low cutting speed and high feed rate. Dominant wear mechanism observed during the experiments were flank and crater wear which is mainly caused by abrasive action of the hard workpiece material with the ceramic cutting tools.

An Experimental Study of Cutting Force on Large Cutting Depth Turning Titanium Alloy with CBN Tool

2014 ◽  
Vol 800-801 ◽  
pp. 237-240
Author(s):  
Li Fu Xu ◽  
Ze Liang Wang ◽  
Shu Tao Huang ◽  
Bao Lin Dai
Keyword(s):  
Experimental Study ◽  
Titanium Alloy ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Cbn Tool ◽  
Cutting Experiment ◽  
Rough Turning

In this paper, the cutting experiment was used to study the influence of various cutting parameters on cutting force when rough turning titanium alloy (TC4) with the whole CBN tool. The results indicate that among the cutting speed, feed rate and cutting depth, the influence of the cutting depth is the most significant on cutting force; the next is the feed rate and the cutting speed is at least.

scholarly journals Experiments in the Machining of Ice at Negative Rake Angles

1984 ◽  
Vol 30 (104) ◽  
pp. 77-81 ◽  
Author(s):  
D.K. Lieu ◽  
C.D. Mote
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
Orthogonal Machining ◽  
Cutting Force Components ◽  
Force Components

AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1to 1 ms−1), and the rake angles (–15° to –60°). Results of the experiments showed that the cutting force components were approximately independent of cutting speed. The resultant cutting force on the tool was in a direction approximately normal to the cutting face of the tool. The magnitude of the resultant force increased with the negative rake angle. Photographs of ice-chip formation revealed continuous and segmented chips at different cutting depths.

scholarly journals Milling Inconel 718 Workpiece With Cryogenically Treated And Untreated Cutting Tools

2021 ◽  
Author(s):  
Hüseyin Gürbüz ◽  
Şehmus Baday
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Abrasive Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Tool Wear ◽  
Feed Force

Abstract Although Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02-0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated.

scholarly journals Technics Research on Polycrystalline Cubic Boron Nitride Cutting Tools Dry Turning Ti-6AL-4V Alloy Based on Orthogonal Experimental Design

2018 ◽  
Vol 142 ◽  
pp. 03002
Author(s):  
Yunhai Jia ◽  
Lixin Zhu
Keyword(s):  
Surface Roughness ◽  
Experimental Design ◽  
Boron Nitride ◽  
Feed Rate ◽  
Flank Wear ◽  
Cubic Boron Nitride ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Orthogonal Experimental Design ◽  
Polycrystalline Cubic Boron Nitride

Ti-6Al-4V components are the most widely used titanium alloy products not only in the aerospace industry, but also for bio-medical applications. The machine-ability of titanium alloys is impaired by their high temperature chemical reactivity, low thermal conductivity and low modulus of elasticity. Polycrystalline cubic boron nitride represents a substitute tool material for turning titanium alloys due to its high hardness, wear resistance, thermal stability and hot red hardness. For determination of suitable cutting parameters in dry turning Ti-6AL-4V alloy by Polycrystalline cubic boron nitride cutting tools, the samples, 300mm in length and 100mm in diameter, were dry machined in a lathe. The turning suitable parameters, such as cutting speed, feed rate and cut depth were determined according to workpieces surface roughness and tools flank wear based on orthogonal experimental design. The experiment showed that the cutting speed in the range of 160~180 m/min, the feed rate is 0.15 mm/rev and the depth of cut is 0.20mm, ideal workpiece surface roughness and little cutting tools flank wear can be obtained.

Sign in / Sign up

Export Citation Format

Share Document