Mechanical Properties and Microstructures of Cement Mortar Modified with Styrene-Butadiene Polymer Emulsion

2010 ◽  
Vol 168-170 ◽  
pp. 190-194 ◽  
Author(s):  
Zhen Jun Wang ◽  
Rui Wang ◽  
Yu Bin Cheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Mortar ◽  
Strength Increase ◽  
Polymer Emulsion ◽  
Cement Ratio ◽  
Cement Mortars ◽  
Water To Cement Ratio ◽  
Styrene Butadiene

In this paper, styrene-butadiene polymer emulsion SD622S was adopted to modify cement mortar; mechanical properties of cement mortars were studied and microstructures was analyzed by means of Scanning Electron Microscope (SEM) and Specific Surface Area & Pore Distribution Analyzer. The results show that in contrast to ordinary cement mortar, if water to cement ratio (W/C) is constant, compressive strength of modified cement mortar can decrease, while flexural strength and toughness, ratio of compressive strength to flexural strength, increase with the increase of polymer to cement ratio in mass (P/C) at 7 and 28 curing days. With the increase of P/C, net structure made from polymer and cement hydration products is developed and pore whose size is smaller than 200Å begins to increase, which indicates pore diameters in modified cement mortar change to be finer. So microstructures of modified cement mortar become denser and display higher toughness.

Effects of Fly Ash Addition on Compressive Strength and Flexural Strength of Foamed Cement Composites

2013 ◽  
Vol 795 ◽  
pp. 664-668 ◽  
Author(s):  
Roshasmawi Abdul Wahab ◽  
Mohd Noor Mazlee ◽  
Shamsul Baharin Jamaludin ◽  
Khairul Nizar Ismail
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Cement Composites ◽  
Volume Percent ◽  
Foaming Agent ◽  
Cement Ratio ◽  
Water To Cement Ratio

In this study, the mixing of polystyrene (PS) beads and fly ash as a sand replacement material in foamed cement composites (FCC) has been investigated. Specifically, the mechanical properties such as compressive strength and flexural strength were measured. Different proportions of fly ash were added in cement composites to replace the sand proportion at 3 wt. %, 6 wt. %, 9 wt. % and 12 wt. % respectively. The water to cement ratio was fixed at 0.65 meanwhile ratios of PS beads used was 0.25 volume percent of samples as a foaming agent. All samples at different mixed were cured at 7 and 28 days respectively. Based on the results of compressive strength, it was found that the compressive strength was increased with the increasing addition of fly ash. Meanwhile, flexural strength was decreased with the increasing addition of fly ash up to 9 wt. %. The foamed cement composites with 12 wt. % of fly ash produced the highest strength of compressive strength meanwhile 3 wt. % of fly ash produced the highest strength of flexural strength.

scholarly journals Effect of Graphene Oxide/Graphene Hybrid on Mechanical Properties of Cement Mortar and Mechanism Investigation

Nanomaterials ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 113 ◽  
Author(s):  
Hongfang Sun ◽  
Li Ling ◽  
Zhili Ren ◽  
Shazim Ali Memon ◽  
Feng Xing
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Graphene Oxide ◽  
Flexural Strength ◽  
Pore Size Distribution ◽  
Cement Mortar ◽  
Underlying Mechanism ◽  
Mortar Specimen ◽  
Degree Of Hydration ◽  
Cement Mortars

This paper evaluated the effect of graphene oxide/graphene (GO/GR) hybrid on mechanical properties of cement mortar. The underlying mechanism was also investigated. In the GO/GR hybrid, GO was expected to act as a dispersant for GR while GR was used as reinforcement in mortar due to its excellent mechanical properties. For the mortar specimen, flexural and compressive strength were measured at varied GO to GR ratios of 1:0, 3:1, 1:1, 1:3, and 0:1 by keeping the total amount of GO and GR constant. The underlying mechanism was investigated through the dispersibility of GR, heat releasing characteristics during hydration, and porosity of mortar. The results showed that GO/GR hybrid significantly enhanced the flexural and compressive strength of cement mortars. The flexural strength reached maximum at GO:GR = 1:1, where the enhancement level was up to 23.04% (28 days) when compared to mortar prepared with only GO, and up to 15.63% (7 days) when compared to mortar prepared with only GR. In terms of compressive strength, the enhancement level for GO:GR = 3:1 was up to 21.10% (3 days) when compared with that of mortar incorporating GO only. The enhancement in compressive strength with mortar at GO:GR = 1:1 was up to 14.69% (7-day) when compared with mortar incorporating GR only. In addition to dispersibility, the compressive strength was also influenced by other factors, such as the degree of hydration, porosity, and pore size distribution of mortar, which made the mortars perform best at different ages.

Incorporation of Iraqi Rocks in the Production of Eco-Friendly Cement Mortar

2020 ◽  
Vol 38 (10A) ◽  
pp. 1522-1530
Author(s):  
Rawnaq S. Mahdi ◽  
Aseel B. AL-Zubidi ◽  
Hassan N. Hashim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Structural Properties ◽  
Mechanical Milling ◽  
Cement Mortar ◽  
Cement Mortars

This work reports on the incorporation of Flint and Kaolin rocks powders in the cement mortar in an attempt to improve its mechanical properties and produce an eco-friendly mortar. Flint and Kaolin powders are prepared by dry mechanical milling. The two powders are added separately to the mortars substituting cement partially. The two powders are found to improve the mechanical properties of the mortars. Hardness and compressive strength are found to increase with the increase of powders constituents in the cement mortars. In addition, the two powders affect water absorption and thermal conductivity of the mortar specimens which are desirable for construction applications. Kaolin is found to have a greater effect on the mechanical properties, water absorption, and thermal conductivity of the mortars than Flint. This behavior is discussed and analyzed based on the compositional and structural properties of the rocks powders.

scholarly journals Preparation of Electric- and Magnetic-Activated Water and Its Influence on the Workability and Mechanical Properties of Cement Mortar

2021 ◽  
Vol 13 (8) ◽  
pp. 4546
Author(s):  
Kaiyue Zhao ◽  
Peng Zhang ◽  
Bing Wang ◽  
Yupeng Tian ◽  
Shanbin Xue ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Paste ◽  
Cement Mortar ◽  
Environmental Issues ◽  
Chemical Admixtures ◽  
Untreated Water ◽  
Alternating Voltage

Cement-based materials prepared with activated water induced by a magnetic field or electric field represent a possible solution to environmental issues caused by the worldwide utilization of chemical admixtures. In this contribution, electric- and magnetic-activated water have been produced. The workability and mechanical properties of cement mortar prepared with this activated water have been investigated. The results indicate that the pH and absorbance (Abs) values of the water varied as the electric and magnetic field changed, and their values increased significantly, exhibiting improved activity compared with that of the untreated water. In addition, activated water still retains activity within 30 min of the resting time. The fluidity of the cement paste prepared with electric-activated water was significantly larger than that of the untreated paste. However, the level of improvement differed with the worst performance resulting from cement paste prepared with alternating voltage activated water. In terms of mechanical properties, both compressive strength and flexural strength obtained its maximum values at 280 mT with two processing cycles. The compressive strength increased 26% as the curing time increased from 7 days to 28 days and flexural strength increased by 31%. In addition, through the introduction of magnetic-activated water into cement mortar, the mechanical strength can be maintained without losing its workability when the amount of cement is reduced.

scholarly journals Properties of Calcium Sulfoaluminate Cement Mortar Modified by Hydroxyethyl Methyl Celluloses with Different Degrees of Substitution

Molecules ◽  
2021 ◽  
Vol 26 (8) ◽  
pp. 2136
Author(s):  
Shaokang Zhang ◽  
Ru Wang ◽  
Linglin Xu ◽  
Andreas Hecker ◽  
Horst-Michael Ludwig ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Bond Strength ◽  
Cement Mortar ◽  
Retention Rate ◽  
Methyl Cellulose ◽  
Tensile Bond Strength ◽  
Calcium Sulfoaluminate Cement ◽  
Calcium Sulfoaluminate ◽  
Cement Mortars

This paper studies the influence of hydroxyethyl methyl cellulose (HEMC) on the properties of calcium sulfoaluminate (CSA) cement mortar. In order to explore the applicability of different HEMCs in CSA cement mortars, HEMCs with higher and lower molar substitution (MS)/degree of substitution (DS) and polyacrylamide (PAAm) modification were used. At the same time, two kinds of CSA cements with different contents of ye’elimite were selected. Properties of cement mortar in fresh and hardened states were investigated, including the fluidity, consistency and water-retention rate of fresh mortar and the compressive strength, flexural strength, tensile bond strength and dry shrinkage rate of hardened mortar. The porosity and pore size distribution were also analyzed by mercury intrusion porosimetry (MIP). Results show that HEMCs improve the fresh state properties and tensile bond strength of both types of CSA cement mortars. However, the compressive strength of CSA cement mortars is greatly decreased by the addition of HEMCs, and the flexural strength is decreased slightly. The MIP measurement shows that HEMCs increase the amount of micron-level pores and the porosity. The HEMCs with different MS/DS have different effects on the improvement of tensile bond strength in different CSA cement mortars. PAAm modification can improve the tensile bond strength of HEMC-modified CSA cement mortar.

Influence of the Composition of Cement Mortars Modified by Lime or Polymers on the Mechanical Properties and Microstructure of Mortars

2013 ◽  
Vol 592-593 ◽  
pp. 647-650 ◽  
Author(s):  
Małgorzata Lenart
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Polyvinyl Alcohol ◽  
Polymer Composites ◽  
Adhesion Strength ◽  
Hardened Cement ◽  
Cement Mortars ◽  
Styrene Butadiene

Cement – polymer composites are nowadays widely used in repair systems not only in case of concrete or reinforced concrete constructions but also in masonry. Polymers addition for example already at 5% m.c. modifies the structure of the cement – polymer composite in a way that many of the mechanical properties such as flexural strength, tensile strength or adhesion to substrates are improved. The paper presents the results of tests such as flexural, compressive or adhesion strength to ceramic substrate of hardened cement mortars with different composition, as well as selected cement mortars modified by two polymers: polyvinyl alcohol and styrene – butadiene polymer dosed at 5 % m.c. Four types of cement mortars modified by lime (component used in historical constructions as well as in contemporary masonry mortars) are also examined for comparison.

EFFECT OF STYRENE-BUTADIENE COPOLYMER (SBR) LATEX ON MECHANICAL AND TRANSPORT PROPERTIES OF PORTLAND CEMENT MORTAR

2020 ◽  
Vol 15 (4) ◽  
pp. 185-197
Author(s):  
Daniel Hatungimana ◽  
Şemsi Yazici ◽  
Şevket Orhan ◽  
Ali Mardani-Aghabaglou
Keyword(s):  
Mechanical Properties ◽  
Portland Cement ◽  
Detrimental Effect ◽  
Cement Mortar ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Replacement Level ◽  
Cement Production ◽  
Cement Ratio ◽  
Styrene Butadiene

ABSTRACT Portland cement is extensively used as a binder in concrete production. However, with Portland cement production, 5% of the natural resources used in this production are consumed, constituting 5–7% of the total CO2 emission. In order to mitigate the environmental problems associated with cement production, styrene-butadiene rubber latex was used as cement replacement up to 20%. In this study, compressive strength, flexural strength, unit weight, water absorption, open porosity, water sorptivity and the chloride ion permeability of Portland cement mortar mixtures modified by styrene-butadiene rubber (SBR) polymeric latex were investigated. For this purpose, the sand/cement ratio and the water/cement ratio were kept constant as 3/1 and 0.5, respectively. In addition to the control mixture containing no polymer, 1, 2, 3, 5, 10 and 20 wt.% of cement was replaced with SBR. In this way, seven mortar mixtures were prepared. Mixed curing (wet cure and dry cure) method was applied to the mortar specimens. Results showed that up to a 5% replacement level, it is possible to improve the mechanical properties of cement mortars with SBR latex addition. However, at a 10% and 20% replacement level, SBR had a significant detrimental effect on the mechanical properties of polymer modified mortars. However, the transport properties decreased with the incorporation rate of SBR latex and the detrimental effect of SBR replacement was more pronounced in 20% SBR mortar mixtures.

scholarly journals Effects of Bacillus subtilis biocementation on the mechanical properties of mortars

2019 ◽  
Vol 12 (1) ◽  
pp. 31-38 ◽  
Author(s):  
N. SCHWANTES-CEZARIO ◽  
M. F. PORTO ◽  
G. F. B. SANDOVAL ◽  
G. F. N. NOGUEIRA ◽  
A. F. COUTO ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Calcium Carbonate ◽  
Cementitious Materials ◽  
Mechanical Analysis ◽  
Sem Analysis ◽  
Subtilis Strain ◽  
Cement Mortars ◽  
Water To Cement Ratio ◽  
Mixing Water

Abstract This study aims to evaluate the influence of B. subtilis AP91 spores addition on the mechanical properties of mortars. B. subtilis strain AP91, isolated from rice leaves of the needle variety, which has an early cycle of production, was used at the concentration of 105 spores/mL in mortars with cement-to-sand ratio of 1:3 (by weight) and water-to-cement ratio (w/c) of 0.63. These spores were added in two different ways: in the mixing water and by immersion in a solution containing bacterial spores. Scanning Electron Microscope (SEM) analysis showed crystals with calcium peaks on the EDS, which possibly indicates the presence of bioprecipitated calcium carbonate. The results obtained in the mechanical analysis showed that the bioprecipitation of CaCO3 by B. subtilis strain AP91 was satisfactory, particularly when the spores were added in the mixing water, increasing the compressive strength up to 31%. Thus, it was concluded that the addition of B. subtilis AP91 spores in the mixing water of cement mortars induced biocementation, which increased the compressive strength. This bioprecipitation of calcium carbonate may very well have other advantageous consequences, such as the closure of pores and cracks in cementitious materials that could improve durability properties, although more research is still needed on this matter.

Performance of ilmenite concrete at sustained elevated temperatures

1988 ◽  
Vol 15 (5) ◽  
pp. 776-783
Author(s):  
H. S. Wilson
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Flexural Strength ◽  
Key Words ◽  
Elevated Temperatures ◽  
Cement Ratio ◽  
Nondestructive Tests ◽  
High Temperature Mechanical Properties ◽  
Curing Period

Two similar mixes were made with cement contents of about 350 kg/m3 and a water–cement ratio of 0.50. The concrete specimens, moist cured for 7 days, were cured in air for 28 and 120 days, respectively, prior to heating. The exposure temperatures were 75, 150, 300, and 450 °C. The periods of exposure at each temperature were 2, 30, and 120 days.The compressive strengths, before heating, of the specimens cured for 35 and 120 days were 41.0 and 46.2 MPa, respectively, and the flexural strengths were 4.9 and 5.8 MPa. Compared with those strengths, the strengths of the specimens heated for 30 days or more increased at 75 °C but decreased at higher temperatures. The losses increased with increase in temperature, reaching about 30% at 450 °C.The flexural strength of the concrete cured in air for 28 days was more adversely affected than was the compressive strength. The flexural and compressive strengths of the concrete cured in air for 120 days were affected to about the same degree. The longer curing period had little effect on the relative losses in compressive strength, but the longer curing period reduced the loss in flexural strength. In most applications, the loss in strength could be compensated by proportioning the mix to overdesign for strength. Key words: high-density concrete, ilmenite, aggregates, high temperature, mechanical properties, nondestructive tests.

Research on Polymer Latex Modify Comprehensive Properties of Cement Mortar

2011 ◽  
Vol 225-226 ◽  
pp. 457-460
Author(s):  
Wei Li
Keyword(s):  
Mechanical Properties ◽  
Cement Mortar ◽  
Drying Shrinkage ◽  
Mix Design ◽  
Cement Ratio ◽  
Comprehensive Properties ◽  
Before And After ◽  
Overall Performance ◽  
Styrene Butadiene ◽  
Polymer Latex

Aimed for current situation that most scholars concerned with mechanics, deformation, flow performance of modified cement mortar, the paper selected carboxyl styrene-butadiene latex as the modified material, researched on cement mortar’ water reducing effect, wear resistance, corrosion resistance-mechanical properties, drying shrinkage before modifing and after modifing. Compared cement fine mortar’s properties with cement mechine-made mortar’s properties before and after modification. Research results showed that the addition of carboxyl SB latex, the overall performance of cement mortar is greatly improved, and with the increase of polymer cement ratio, this improvement trend is more obvious, those changes especially are suitable for extra-fine cement mortar. The results clarify the properties variation law of cement mortar before and after modification, this provides scientific guidance for polymer latex modified cement mortar mix design.

Sign in / Sign up

Export Citation Format

Share Document