Experimental Research on Cutting Temperature of Cemented Carbide Tools during Cutting Austenitic Manganese Steel

2011 ◽  
Vol 413 ◽  
pp. 347-350
Author(s):  
Gui Quan Han ◽  
Zeng Zhi Zhang
Keyword(s):  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cemented Carbide ◽  
Manganese Steel ◽  
Dry Cutting ◽  
Austenitic Manganese Steel ◽  
Austenitic Manganese ◽  
Cemented Carbide Tools

The cutting temperature rules of cemented carbide tools YW2 during cutting austenitic manganese steel ZGMn13 were investigated by experiments through systematically changing cutting parameters (cutting speed, feed, cutting depth) under the condition of dry cutting. The experiential expressions for cutting temperature of tools were summarized while dominating factors for influencing cutting temperature were analyzed. The results show that accounting values by experiential formulae basically match actually measuring values by experiments which may play an important role in studying cutting law of austenitic manganese steel. Cutting speed plays a major role in determining the temperature of cutting tools, followed by feed rate and depth of cutting.

Experimental Study on the Cutting Temperature with Micro-Texturing Self-Lubricated Tools

2011 ◽  
Vol 291-294 ◽  
pp. 715-720
Author(s):  
Ze Wu ◽  
Jian Xin Deng ◽  
Yun Song Lian ◽  
Zhi Jun Wang ◽  
Jun Zhao
Keyword(s):  
Experimental Study ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Hardened Steel ◽  
Cemented Carbide ◽  
Dry Cutting ◽  
Cemented Carbide Tools

Micro-texturing self-lubricated cutting tools named MTR-1 and MTR-3 were designed and made based on micro-texturing lubricating idea and laser micro-texturing technology. Dry cutting tests on 45# hardened steel were carried out with these self-lubricated cutting tools and conventional cemented carbide tools named MT0. The cutting temperatures and the morphology of chips were measured. The results indicated that the cutting temperatures with the micro-texturing self-lubricated cutting tools were reduced compared with that of MT0 cemented carbide tools, and the chip coiling was improved.

scholarly journals Study on the Cutting Performance of Micro Textured Tools on Cutting Ti-6Al-4V Titanium Alloy

Micromachines ◽  
2020 ◽  
Vol 11 (2) ◽  
pp. 137 ◽  
Author(s):  
Kairui Zheng ◽  
Fazhan Yang ◽  
Na Zhang ◽  
Qingyu Liu ◽  
Fulin Jiang
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Cutting Force ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Performance ◽  
Cemented Carbide ◽  
Feed Force ◽  
Cemented Carbide Tools

Titanium alloys are widely used in various fields, but their machinability is poor because the chip would easily adhere to the tool surface during cutting, causing poor surface quality and tool wear. To improve the cutting performance of titanium alloy Ti-6Al-4V, experiments were conducted to investigate the effect of micro textured tool on the cutting performances. The cemented carbide tools whose rake faces were machined with line, rhombic, and sinusoidal groove textures with 10% area occupancy rates were adopted as the cutting tools. The effects of cutting depth and cutting speed on feed force and main cutting force were discussed based on experimental results. The results show that the cutting force produced by textured tools is less than that produced by non-textured tools. Under different cutting parameters, the best cutting performance can be obtained by using sinusoidal textured tools among the four types of tools. The wear of micro textured tools is significantly lower than that of non-textured tools, due to a continuous lubrication film between the chip and the rake face of the tool that can be produced because the micro texture can store and replenish lubricant. The surface roughness obtained using the textured tool is better than that using the non-textured tool. The surface roughness Ra can be reduced by 35.89% when using sinusoidal textured tools. This study is helpful for further improving the cutting performance of cemented carbide tools on titanium alloy and prolonging tool life.

scholarly journals Machining Performance of TiAlN-Coated Cemented Carbide Tools with Chip Groove in Machining Titanium Alloy Ti-6Al-0.6Cr-0.4Fe-0.4Si-0.01B

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 850 ◽  
Author(s):  
Zhaojun Ren ◽  
Shengguan Qu ◽  
Yalong Zhang ◽  
Xiaoqiang Li ◽  
Chao Yang
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cemented Carbide ◽  
Machining Performance ◽  
Cemented Carbide Tools ◽  
Optimal Cutting Parameters ◽  
Coated Cemented Carbide

In this paper, TiAlN-coated cemented carbide tools with chip groove were used to machine titanium alloy Ti-6Al-0.6Cr-0.4Fe-0.4Si-0.01B under dry conditions in order to investigate the machining performance of this cutting tool. Wear mechanisms of TiAlN-coated cemented carbide tools with chip groove were studied and compared to the uncoated cemented carbide tools (K20) with a scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). The effects of the cutting parameters (cutting speed, feed rate and depth of cut) on tool life and workpiece surface roughness of TiAlN-coated cemented carbide tools with chip groove were studied with a 3D super-depth-of-field instrument and a surface profile instrument, respectively. The results showed that the TiAlN-coated cemented carbide tools with chip groove were more suitable for machining TC7. The adhesive wear, diffusion wear, crater wear, and stripping occurred during machining, and the large built-up edge formed on the rake face. The optimal cutting parameters of TiAlN-coated cemented carbide tools were acquired. The surface roughness Ra decreased with the increase of the cutting speed, while it increased with the increase of the feed rate.

Force and Temperature in Dry Cutting of Hardened W18Cr4V with PCBN

2010 ◽  
Vol 431-432 ◽  
pp. 559-563
Author(s):  
Hai Rong Wu ◽  
Guo Qin Huang ◽  
Xi Peng Xu
Keyword(s):  
Experimental Study ◽  
Cutting Force ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Dry Cutting ◽  
Feeding Speed ◽  
Strain Gauge Dynamometer ◽  
Three Components

An experimental study was carried out to investigate the effects of cutting parameters on cutting force and temperature in cutting of hardened W18Cr4V with PCBN cutter. Three components of cutting force were recorded by a strain-gauge dynamometer and the cutting temperature was measured by a nature thermocouple of tool-workpiece. The cutting parameters were arranged by orthogonal method. It is shown that the cutting temperature increased with each of the three cutting parameters and the main effecting factor is feeding speed. The three components of cutting force increased greatly with an increase in feeding speed and cutting depth. But the forces decreased a little as cutting speed increased. The main and axial cutting forces depend mainly on cutting depth whereas the radius force is mainly influenced by feeding speed.

Three-dimensional finite element modeling of effect on the cutting forces of rake angle and approach angle in milling

2016 ◽  
Vol 231 (2) ◽  
pp. 83-88 ◽  
Author(s):  
Kadir Gok ◽  
Hüseyin Sari ◽  
Arif Gok ◽  
Süleyman Neseli ◽  
Erol Turkes ◽  
...  
Keyword(s):  
Cutting Tools ◽  
Three Dimensional ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Milling Operations ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In this study, milling operations were carried out using AISI 1040 specimens steel in dry cutting conditions. The cutting tools used in the experiment include P20 tool steel and they also have three different approach angles (45°, 60°, 75°) and rake angles (0°, −6°, −12°). In milling experiments, cutting parameters with a depth of cut of 1.5 mm, cutting speed of 193 m/min, and feed rate of 313 mm/min were selected. A comparison was presented between the force values which were obtained by measured value and predicted with numerical simulations, and then a good agreement was found between measured and predicted force values. As result of, it was observed that the rake and approach angles were effective in milling operations.

Research on the Surface Roughness of Dry Cutting Different Levels of Austempering Ductile Iron (ADI)

2011 ◽  
Vol 464 ◽  
pp. 496-500
Author(s):  
Xiao Hong Xue ◽  
Xu Hong Guo ◽  
Ting Ting Chen ◽  
Dong Dong Wan ◽  
Qiao Wang
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cubic Boron Nitride ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Isothermal Quenching ◽  
Dry Cutting ◽  
Quenching Temperature

Three cutting tools of different materials (ceramics CC6050, cubic boron nitride CB7025, carbide GC2025) are used for dry turning of 9 groups of ADI which heat-treated under different quenching time and quenching temperature. The surface roughness of ADI workpieces were tested after the finish turning at changed cutting parameters, and the influencing factors of surface quality were analysed. Results showed that the surface roughness values of all 9 groups of ADI workpieces obtained by CC6050 were the lowest and the surface quality was better at lower depth of cut ap and feed rate f with higher cutting speed vc . Meanwhile, the surface roughness was influenced by the isothermal quenching parameters of ADI workpieces significantly.

Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy

2013 ◽  
Vol 589-590 ◽  
pp. 361-365
Author(s):  
Xiao Di Ma ◽  
Jiu Hua Xu ◽  
Wen Feng Ding ◽  
Dong Sheng Lv ◽  
Yu Can Fu
Keyword(s):  
Wear Mechanisms ◽  
Failure Modes ◽  
Wear Behavior ◽  
Cutting Speed ◽  
Base Material ◽  
Cutting Parameters ◽  
Cemented Carbide ◽  
Nickel Base ◽  
Cemented Carbide Tools ◽  
Coated Cemented Carbide

Ti2AlNb-based alloy is regarded as lightweight high-temperature structural material, which is expected to replace the nickel-base super alloy due to its low density, high elastic modulus, strength retention at elevated temperature, outstanding oxide resistance. However, these excellent properties also make Ti2AlNb to be difficult-to-cut material. In this paper, the milling experiment of Ti2AlNb alloy was carried out using Ti(N,C)-Al2O3 coated cemented carbide tools. SEM and EDS analysis was utilized to observe the worn tools to determine the tool failure modes and wear mechanisms. Tool life when milling Ti2AlNb was short and heavily dependent on the cutting parameters. During milling, coating material of the tool was separated rapidly from the base material. When the cutting speed exceeded 100m/min, serious cracks appeared on the tool surface. Thermal fatigue, adhesive and attrition were the predominant wear mechanisms of the coated tools.

scholarly journals Effect of Built-Up Edge Formation on Residual Stresses Induced by Dry Cutting of Normalized Steel

2014 ◽  
Vol 996 ◽  
pp. 603-608
Author(s):  
Johannes Kümmel ◽  
Jens Gibmeier ◽  
Volker Schulze ◽  
Alexander Wanner
Keyword(s):  
Surface Layer ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Wear Behaviour ◽  
Dry Cutting ◽  
Workpiece Material ◽  
Workpiece Surface

The tool and workpiece surface layer states of the tribosystem uncoated WC-Co cutting tools vs. normalised SAE 1045 workpiece material are studied in detail for a dry metal cutting process. Within the system the cutting parameters (cutting speed, feed rate, cutting depth) determine the wear state of the cutting tool and the resulting surface layer state (residual stress) in the workpiece. As the built-up edge can be used as a possible wear protecting layer [1] the influence of built-up edge and wear behaviour of the cutting tool was examined with respect to the workpiece surface layer state for knowledge based metal cutting processing. Small compressive stresses (-60-80 MPa) are induced in the surface layer, that are nearly homogeneous for the highest built-up edge, which lead to the lowest tool wear in combination with lowest cutting temperature.

scholarly journals Study on Technological Effects of a Precise Grooving of AlSi13MgCuNi Alloy with a Novel WCCo/PCD (DDCC) Inserts

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2467 ◽  
Author(s):  
Szymon Wojciechowski ◽  
Rafał Talar ◽  
Paweł Zawadzki ◽  
Stanisław Legutko ◽  
Radosław Maruda ◽  
...  
Keyword(s):  
Tool Life ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Fold Increase ◽  
Cutting Parameters ◽  
Cemented Carbide ◽  
Machining Parameters ◽  
Tungsten Carbides ◽  
Machined Surface ◽  
Cutting Path

The WCCo/PCD (Diamond Dispersed Cemented Carbide—DDCC) manufactured with the use of PPS (pulse plasma sintering) are modern materials intended for cutting tools with the benefits of tungsten carbides and polycrystalline diamonds. Nevertheless, the cutting performance of DDCC materials are currently not recognized. Thus this study proposes the evaluation of technological effects of a precise groove turning process of hard-to-cut AlSi13MgCuNi alloy with DDCC tools. The conducted studies involved the measurements of machined surface topographies after grooving with different cutting parameters. In addition, the tool life and wear tests of DDCC inserts were conducted during grooving process and the obtained results were compiled with values reached during machining with cemented carbide tools. It was also proved that grooving of AlSi13MgCuNi alloy with DDCC inserts enables 5 times longer tool life and almost 3-fold increase of cutting path compared to values obtained during grooving with H3 and H10 cemented carbide inserts. Ultimately, the feed value of f = 0.15 mm/rev and cutting speed in a range of 800 m/min ≤ vc ≤ 1000 m/min during grooving with DDCC inserts can be defined as an optimal machining parameters, enabling the maximization of tool life and improvement in surface quality.

Recent Development of Parameter Optimization for Metal Cutting and Grinding Processes

2013 ◽  
Vol 652-654 ◽  
pp. 2218-2221 ◽  
Author(s):  
Li Bao An ◽  
Chun Guang Lu
Keyword(s):  
Parameter Optimization ◽  
High Speed ◽  
Metal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Optimization Techniques ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Optimization Of Cutting Parameters

Metal cutting indicates a specific category of processes in which unwanted material is removed from workpeice by single- or multi-point cutting tools for making products meeting prescribed specifications. Parameter optimization in metal cutting plays an important role in satisfying quality requirements of machined parts at low production cost or time. It requires optimal selection of cutting speed, feed rate, depth of cut, and the number of passes. A brief review of recent progress on the optimization of cutting parameters is introduced in the present work. Some new machining practices expending in recent years are involved including hard turning, dry cutting, high speed machining, machining of difficult-to-machine materials and composites. Modeling skills for creating optimization models and optimization techniques for solving optimal or near-optimal solutions are summarized and analyzed.

Sign in / Sign up

Export Citation Format

Share Document