Two New Flow Control Technologies Based on Vibration

2013 ◽  
Vol 774-776 ◽  
pp. 326-334
Author(s):  
Da Wei Li ◽  
Jin Hao Qiu ◽  
Rui Nie ◽  
Hong Li Ji
Keyword(s):  
Mach Number ◽  
Active Control ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Computational Method ◽  
Control Effect ◽  
Active Deformation ◽  
Wing Model ◽  
Control Technologies

This paper aims at study the technology of flow active control to increase the wing lift and weaken the wing drag by using the method of fluid mechanics. There are two new active control methods proposed in this paper. In this article, the computational method is expanded to a three-dimensional wing model to verify the validity of the new active control technology. Research shows that the partial active deformation can improve the aerodynamic characteristics of airfoil by appropriate parameters optimize, moreover the effect of rotation was better. In the condition of low Mach number and rotational control, the lift coefficient can be increased 11%, the drag coefficient can be decreased 40%. The shock wave will move backward by control in the condition of high Mach number. The control effect of 3D model is not as good as 2D model.

Numerical Simulation on Aerodynamics of Ramjet Projectiles

2011 ◽  
Vol 201-203 ◽  
pp. 89-92 ◽  
Author(s):  
Jia Xian Zhang ◽  
Yan Na Wang ◽  
Rui Min Liu
Keyword(s):  
Numerical Simulation ◽  
Mach Number ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Numerical Algorithms ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Pressure Center ◽  
Complex Wave ◽  
Center Increase

Three-dimensional Reynolds-averaged Navier-Stokes simulations have been performed to explore the aerodynamic characteristics of ramjet projectiles. The turbulence model used is the RNG k-ε model. The numerical algorithms termed total variational diminishing (TVD) was adopted. The complex wave structures of ramjet projectiles with different architecture at different inflow Mach number were achieved by numerical simulation. The influence of inflow Mach number on aerodynamic characteristics and pressure center of ramjet projectiles were analyzed. Results show that lift coefficient and pressure center increase with the argument of inflow Mach number. Ramjet projectiles with different architecture have different drag coefficient trend.

The Effect of Canard to the Aerodynamic Behavior of Blended Wing Body Aircraft

2012 ◽  
Vol 225 ◽  
pp. 38-42
Author(s):  
Zurriati Mohd Ali ◽  
Wahyu Kuntjoro ◽  
Wisnoe Wirachman
Keyword(s):  
Mach Number ◽  
Wind Tunnel ◽  
Aerodynamic Characteristic ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Moment Coefficient ◽  
Subsonic Wind Tunnel ◽  
Setting Angle ◽  
Blended Wing Body ◽  
The Moment

This paper presents a study on the effect of canard setting angle on the aerodynamic characteristic of a Blended Wing Body (BWB). Canard effects to BWB aerodynamic characteristics are not widely investigated. Hence the focus of the study is to investigate the variations of lifts, drags and moments when the angles of attack are varied at different canard setting angles. Wind tunnel tests were performed on BWB aircraft with canard setting angles,  ranging from -20˚ to 20˚. Angles of attack,  were varied from -10˚ to 10˚. Aspect ratio and canard planform area were kept fixed. All tests were conducted in the subsonic wind tunnel at Universiti Teknologi MARA, at Mach number of 0.1. The streamlines flow, at the upper surface of the canard was visualized using mini tuft. Result shows that the lift coefficient does not change much with different canard setting angles. As expected, the lift coefficient increases with increasing angles of attack at any canard setting angle. In general, the moment coefficient increases as the canard setting angle is increased. The results obtained in this research will be of importance to the understanding of aerodynamic behavior of BWB employing canard in its configuration.

scholarly journals Research on the forward flight performance of rotor based on variable-droop leading edge

2021 ◽  
Vol 39 (3) ◽  
pp. 668-674
Author(s):  
Congcong Li ◽  
Yongjie SHI ◽  
Guohua Xu ◽  
Xingliang Liu
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Integral Form ◽  
Simulation Method ◽  
Aerodynamic Characteristics ◽  
Control Effect ◽  
Forward Flight ◽  
Force Coefficient

Aiming at the dynamic stall phenomenon of the retreating side of the rotor in forward flight, the existing flow control method of dynamic leading edge droop was applied to the flow control of forward-flying rotor at three-dimensional scale. A numerical simulation method based on variable droop leading edge is established in this paper. The seesaw rotor is taken as the research object, the moving overset mesh method and RBF grid deformation technology are used, the integral form of Reynolds average N-S equation is the main control equation. The influence of the dynamic leading edge at r/R=0.75~1 on the aerodynamic characteristics of the rotor when the forward ratio is 0.3 is investigated. It is found that variable droop leading edge on the retreating side can effectively inhibit the generation and development of separation vortices near the trailing edge, and has a significant effect on lifting lift coefficient and section normal force coefficient, reducing torque coefficient, and thus improving the equivalent lift-drag ratio of the rotor. In a certain range, the control effect is better with the increase of the droop amplitude under the leading edge.

Three-Dimensional Wing Design Towards the Future Mars Airplane

2011 ◽  
Author(s):  
Ryoji Kojima ◽  
Donghi Lee ◽  
Tomoaki Tatsukawa ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Viscous Drag ◽  
Stream Velocity ◽  
Main Stream ◽  
Lower Reynolds Number

The effects of aspect ratio and Reynolds number on aerodynamic characteristics of three-dimensional rectangular wing at low Reynolds number of 103 to 105, are investigated with Reynolds-averaged Navier-Stokes solver with the Baldwin-Lomax model. Present results show that lift coefficient decreases drastically at lower aspect ratio than 4. Besides, the much larger viscous drag coefficient is obtained at the lower Reynolds number, especially lower than 104. In order to focus on designing practical wings, the particular cases under the condition of fixed wing-surface area and fixed main stream velocity are conducted. The results show that there is trade-off between the decrease in viscous drag coefficient with increasing Reynolds number and the increase in lift coefficient with increasing aspect ratio. At the lower Reynolds number condition, as the former effect is stronger than the latter one, maximum lift-to-drag ratio is obtained at lower aspect ratio.

Aerodynamic analysis and design of Busemann biplane: towards efficient supersonic flight

2011 ◽  
Vol 226 (2) ◽  
pp. 217-238 ◽  
Author(s):  
D Maruyama ◽  
K Kusunose ◽  
K Matsushima ◽  
K Nakahashi
Keyword(s):  
Mach Number ◽  
Design Method ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
The Body ◽  
Analysis And Design ◽  
Expansion Waves ◽  
Mach Numbers ◽  
Inverse Design Method

Aiming to realize a low-drag supersonic transport, Busemann biplane concept was adopted in this study. Two- and three-dimensional (2D and 3D) biplanes were analysed and designed to improve their aerodynamic performance using computational fluid dynamics. It was confirmed that 3D biplane wings have better aerodynamic-performance areas than 2D biplane airfoils. A winglet is also useful for improvement of their aerodynamic performance. Aerodynamic characteristics of these biplanes at their off-design conditions were also analysed. In 3D wings, a flow choking and its attendant hysteresis as starting problems, which arise when the biplanes accelerate from low Mach numbers, disappear at lower Mach numbers than those in 2D airfoils. It was confirmed that hinged slats and flaps are effective to settle these issues. Finally, interference effects of a body with the biplanes were investigated. When the biplane wings are affected by the expansion waves from the body, their aerodynamic performance at the design Mach number and the starting Mach number are better and lower than those of their isolated wings, respectively. A 3D biplane wing obtained by an inverse-design method was applied to the body. The wing of this wing–body configuration achieves higher aerodynamic performance than the 2D flat-plate airfoil at sufficient lift conditions, which is the almost identical performance of 2D biplane airfoils.

scholarly journals Investigation of Aerodynamic Characteristics of a Wing Model With RGV Winglet

2020 ◽  
Author(s):  
Sivaraj Gopal Krishnan ◽  
Mohammad Hafifi Ishak ◽  
Mohammad Azwan Nasirudin ◽  
Farzad Ismail
Keyword(s):  
Drag Coefficient ◽  
Lift Coefficient ◽  
Vortex Formation ◽  
Aerodynamic Characteristics ◽  
Contour Plot ◽  
Tip Vortices ◽  
Wing Model ◽  
Plot Analysis ◽  
Computational Fluid Dynamics Cfd ◽  
Drag Ratio

This work describes the aerodynamic characteristics of an aircraft wing model with a Rüppell’s griffon vulture (RGV)-type winglet. A computational fluid dynamics (CFD) study using ANSYS 15.0 was conducted to study the effect of the RGV winglet on a rectangular wing. The NACA 65(3)-218 wing consists of 660 mm span and 121 mm chord length where the aspect ratio is 5.45. Eight different winglet configurations have been studied. Furthermore, the study is extended to study effect of cant angle and different angles of attack (AOA) to the winglet. A comparative study is done on aerodynamic features such as lift coefficient (CL), drag coefficient (CD), lift/drag ratio (CL/CD) and tip vortices to get the best RGV winglet design. The RGV winglet achieved highest CL compared to other types of winglets configuration. Based on contour plot analysis, the RGV winglet shows lower vortex formation compared to without winglet. The results show about 15 to 30% reduction in drag coefficient and 5 to 25% increase in lift coefficient by using an RGV winglet.

Model-based analysis of boundary layer ingestion effect on lateral-directional aerodynamics using differentiated boundary conditions

2016 ◽  
Vol 231 (13) ◽  
pp. 2452-2463
Author(s):  
Jing Zhang ◽  
Xianfa Zeng ◽  
Lingyu Yang
Keyword(s):  
Boundary Layer ◽  
Boundary Conditions ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Propulsion System ◽  
Computational Method ◽  
Body Type ◽  
Detailed Model ◽  
Model Based ◽  
Distributed Propulsion

The noteworthy feature of aircraft with distributed propulsion configuration is the integration of a blended-wing-body type airframe and an embedded distributed propulsion system, thus inducing the specific boundary layer ingestion effect. Different boundary layer ingestion effects on the distributed engines may generate asymmetric flow fields on the airframe surface, and then lead to the unique lateral-directional aero-propulsive close coupling. To investigate the lateral-directional aerodynamics influenced by boundary layer ingestion, a new comprehensive computational method based on the differentiated boundary conditions is proposed. This method uses a synthetic three-dimensional computational model including the airframe and multi-engine to analyze the aerodynamic characteristics, and the essential boundary conditions can be extracted from the thermodynamic distributed propulsion system model to represent the different boundary layer ingestion intensities on the left and right engines. Subsequently, detailed model-based analyses of boundary layer ingestion influences on the lateral-directional aerodynamic characteristics are conducted, and the influence regularities under different flight states are revealed. All the results demonstrate that the differentiated boundary layer ingestion intensities on distributed engines can certainly affect the roll and yaw aerodynamic performance of the distributed propulsion configuration aircraft.

Validation of Numerical Analysis to Estimate Airfoil Aerodynamic Characteristics at Low Reynolds Number Region

2015 ◽  
Author(s):  
Donghwi Lee ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
Kozo Fujii
Keyword(s):  
Reynolds Number ◽  
Numerical Method ◽  
Low Reynolds Number ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Eddy Simulation ◽  
Low Reynolds

In this study, two-dimensional laminar simulation (2-D Lam), two-dimensional Reynolds Averaged Navier-Stokes simulation with the Spalart-Allmaras turbulence model (2-D RANS(SA)), and implicit three-dimensional large-eddy simulation (3-D LES) are performed for NACA0012, NACA0006, and Ishii airfoils at Rec = 3.0 × 104. The relation between a predictability of airfoil aerodynamic characteristics and a dependence of airfoil geometry shape of each numerical method is evaluated at the low Reynolds number. Although little discrepancy is observed for the lift coefficient predictability, significant differences are presented in terms of the separation and reattachment points predictability depending on the numerical methods. The 2-D Lam simulation can predict the lift coefficients as well as the separation and reattachment points qualitatively as similar to the 3-D LES results except for the high angle of attack which is accompanied by the massive separation. The 2-D RANS(SA), the weak nonlinearity and stall phenomena for the lift coefficients are observed. A good predictability of the separation point are shown, however, it cannot be estimated the reattachment points due to the trend to predict widely for the separation region. The predictabilities of each numerical method appear regardless of the airfoil shapes.

Aerodynamic Characteristics of the LS(1)-0417MOD Airfoil Model

2003 ◽  
Author(s):  
Jolanta M. Janiszewska ◽  
Gerald Gregorek ◽  
John Lee
Keyword(s):  
Steady State ◽  
Unsteady Flow ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Hysteresis Loops ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Vortex Generators ◽  
Three Dimensional Model ◽  
Three Dimensional Configuration

The LS(1)-0417MOD airfoil model was tested in The Ohio State University’s 3×5 wind tunnel both clean and with the application of leading edge grit roughness and with vortex generators. The tests were conducted in both two-dimensional and three-dimensional model configurations and for steady state and unsteady flow conditions. Pressure data were obtained from six spanwise stations. The results showed that the application of the grit roughness reduces the maximum lift coefficients in all configurations. Unsteady maximum lift coefficients were always higher than those for steady state and had, generally, large hysteresis loops. In the case of the unsteady flow however, the hysteresis loops were smaller for the three dimensional (wing) flows. The smallest hysteresis loops were found at the tip spanwise station. The application of the vortex generators at certain chordwise locations reduced the hysteresis loops and increased the maximum lift coefficient, especially in the three dimensional configuration.

Optimisation and analysis of efficiency for contra-rotating propellers for high-altitude airships

2019 ◽  
Vol 123 (1263) ◽  
pp. 706-726
Author(s):  
J. Tang ◽  
X. Wang ◽  
D. Duan ◽  
W. Xie
Keyword(s):  
Reynolds Number ◽  
Mach Number ◽  
High Altitude ◽  
Reference Frames ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Optimization Approach ◽  
Axial Distance ◽  
The Individual

ABSTRACTAn improved variational optimization approach is established to optimize and analyse the propulsion efficiency of the high-altitude contra-rotating propellers for high-altitude airships based on the Vortex Lattice Lifting Line Method. The optimum radial circulation distribution, chord and pitch distribution are optimized under the maximum lift-to-drag ratio of aerofoils. To consider the effects of the actual Reynolds number and the Mach number of each aerofoil section, aerodynamics such as lift coefficient, drag coefficient and lift-to-ratio are obtained by interpolating a CFD database, which is established by numerical simulations under different Reynolds number, Mach number and angles-of-attack. The improved method is verified by validation cases on a high-altitude CRP using the three-dimensional steady Reynolds-averaged Navier-Stokes solver and moving reference frames technique. The optimization results of thrust, torque and efficiency for both the individual front/rear propeller and CRP are shown to agree reasonably well with the CFD results. Using the improved approach, the influence of blade numbers, diameter, rotation speeds, axial distance and torque ratio on the optimum efficiency of CRPs is illustrated in detail by conducting parametric studies.

Sign in / Sign up

Export Citation Format

Share Document