scholarly journals Research on the forward flight performance of rotor based on variable-droop leading edge

2021 ◽  
Vol 39 (3) ◽  
pp. 668-674
Author(s):  
Congcong Li ◽  
Yongjie SHI ◽  
Guohua Xu ◽  
Xingliang Liu
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Integral Form ◽  
Simulation Method ◽  
Aerodynamic Characteristics ◽  
Control Effect ◽  
Forward Flight ◽  
Force Coefficient

Aiming at the dynamic stall phenomenon of the retreating side of the rotor in forward flight, the existing flow control method of dynamic leading edge droop was applied to the flow control of forward-flying rotor at three-dimensional scale. A numerical simulation method based on variable droop leading edge is established in this paper. The seesaw rotor is taken as the research object, the moving overset mesh method and RBF grid deformation technology are used, the integral form of Reynolds average N-S equation is the main control equation. The influence of the dynamic leading edge at r/R=0.75~1 on the aerodynamic characteristics of the rotor when the forward ratio is 0.3 is investigated. It is found that variable droop leading edge on the retreating side can effectively inhibit the generation and development of separation vortices near the trailing edge, and has a significant effect on lifting lift coefficient and section normal force coefficient, reducing torque coefficient, and thus improving the equivalent lift-drag ratio of the rotor. In a certain range, the control effect is better with the increase of the droop amplitude under the leading edge.

Investigations of synthetic jet control effects on helicopter rotor in forward flight based on the CFD method

2018 ◽  
Vol 122 (1253) ◽  
pp. 1102-1122
Author(s):  
Q.-J. Zhao ◽  
X. Chen ◽  
Y.-Yang Ma ◽  
G.-Q. Zhao
Keyword(s):  
Aerodynamic Characteristic ◽  
Active Flow Control ◽  
Lift Coefficient ◽  
Grid Method ◽  
Simulation Method ◽  
Synthetic Jet ◽  
Control Effect ◽  
Forward Flight ◽  
Suction Surface ◽  
Jet Control

ABSTRACTTo investigate the control effect of the synthetic jet on the aerodynamic characteristic of rotors, a numerical simulation procedure for the rotor flowfield is established. First, a moving-embedded grid method and an unsteady Reynolds Averaged Navier–Stokes (URANS) solver are established for predicting the complex flowfield of rotors. A velocity jet boundary condition over the jet actuator orifice is constructed, and a numerical method for simulating the active flow control on rotors is developed. Then, the effectiveness of the simulation method is validated by comparing the numerical results of jet control on NACA 0015 aerofoil with the experimental data. At last, the aerodynamic characteristic of rotors with synthetic jet actuators located on the suction surface of the blade in forward flight is calculated. The results indicate that the synthetic jet has the capability of improving the aerodynamic characteristic of rotors, especially in inhibiting the flow separation over the surface. In addition, the increase of the jet momentum coefficient and the jet angle can both enhance the lift coefficient in the retreating side. Compared with a single jet, jet arrays have better control effects on improving the aerodynamic characteristic of rotors in forward flight.

Numerical study of the aerodynamic and power characteristics of the cycloidal rotor, under incoming flow

2019 ◽  
pp. 25-34
Author(s):  
Александр Анатольевич Дектерев ◽  
Артем Александрович Дектерев ◽  
Юрий Николаевич Горюнов
Keyword(s):  
Flow Velocity ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Simulation Method ◽  
Aerodynamic Characteristics ◽  
Incoming Flow ◽  
Ansys Fluent ◽  
Energy Characteristics ◽  
Power Characteristics ◽  
Calculation Results

Исследование направлено на разработку и апробацию методики численного моделирования аэродинамических и энергетических характеристик циклоидального ротора. За основу взята конфигурация ротора IAT21 L3. Для нее с использованием CFD-пакета ANSYS Fluent построена математическая модель и выполнен расчет. Проанализировано влияние скорости набегающего потока воздуха на движущийся ротор. Математическая модель и полученные результаты исследования могут быть использованы при создании летательных аппаратов с движителями роторного типа. This article addresses the study of the aerodynamic and energy characteristics of a cycloidal rotor subject to the influence of the incoming flow. Cycloidal rotor is one of the perspective devices that provide movement of aircrafts. Despite the fact that the concept of a cycloidal rotor arose in the early twentieth century, the model of a full-scale aircraft has not been yet realized. Foreign scientists have developed models of aircraft ranging in weight from 0.06 to 100 kg. The method of numerical calculation of the cycloidal rotor from the article [1] is considered and realized in this study. The purpose of study was the development and testing of a numerical simulation method for the cycloidal rotor and study aerodynamic and energy characteristics of the rotor in the hovering mode and under the influence of the oncoming flow. The aerodynamic and energy characteristics of the cycloidal rotor, rotating at a speed of 1000 rpm with incoming flow on it with velocities of 20-80 km/h, were calculated. The calculation results showed a directly proportional increase of thrust with an increase of the incoming on the rotor flow velocity, but the power consumed by the rotor was also increased. Increase of the incoming flow velocity leads to the proportional increasing of the lift coefficient and the coefficient of drag. Up to a speed of 80 km/h, an increase in thrust and power is observed; at higher speeds, there is a predominance of nonstationary effects and difficulties in estimating the aerodynamic characteristics of the rotor. In the future, it is planned to consider the 3D formulation of the problem combined with possibility of the flow coming from other sides.

Dual-position excitation technique in flow control over an airfoil at low speeds

2018 ◽  
Vol 30 (9) ◽  
pp. 4141-4154
Author(s):  
Abbas Ebrahimi ◽  
Majid Hajipour ◽  
Kamran Ghamkhar
Keyword(s):  
Flow Control ◽  
Shear Layer ◽  
Control Method ◽  
Lift Coefficient ◽  
Shear Layers ◽  
Control Flow ◽  
Plasma Actuators ◽  
Dbd Plasma ◽  
Surface Shear ◽  
Content Type

PurposeThe purpose of this paper is to control flow separation over a NACA 4415 airfoil by applying unsteady forces to the separated shear layers using dielectric barrier discharge (DBD) plasma actuators. This novel flow control method is studied under conditions which the airfoil angle of attack is 18°, and Reynolds number based on chord length is 5.5 × 105.Design/methodology/approachLarge eddy simulation of the turbulent flow is used to capture vortical structures through the airfoil wake. Power spectral density analysis of the baseline flow indicates dominant natural frequencies associated with “shear layer mode” and “wake mode.” The wake mode frequency is used simultaneously to excite separated shear layers at both the upper surface and the trailing edge of the airfoil (dual-position excitation), and it is also used singly to excite the upper surface shear layer (single-position excitation).FindingsBased on the results, actuations manipulate the shear layers instabilities and change the wake patterns considerably. It is revealed that in the single-position excitation case, the vortices shed from the upper surface shear layer are more coherent than the dual-position excitation case. The maximum value of lift coefficient and lift-to-drag ratio is achieved, respectively, by single-position excitation as well as dual-position excitation.Originality/valueThe paper contributes to the understanding and progress of DBD plasma actuators for flow control applications. Further, this research could be a beneficial solution for the promising design of advanced low speed flying vehicles.

scholarly journals Numerical studies on aerodynamics of high-speed railway train subjected to strong crosswind

2019 ◽  
Vol 11 (11) ◽  
pp. 168781401988727
Author(s):  
Xu Wang ◽  
Yuanhao Qian ◽  
Zengshun Chen ◽  
Xiao Zhou ◽  
Huaqiang Li ◽  
...  
Keyword(s):  
Wind Speed ◽  
High Speed ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Width Ratio ◽  
Force Coefficient ◽  
Rolling Moment ◽  
Side Force ◽  
Train Speed ◽  
Yaw Angle

Under the action of strong crosswind, the aerodynamic behavior of a rail vehicle at high speed will be changed significantly, which could directly affect the safe operation of the vehicle. With the help of the shape of train used in China, the aerodynamic characteristics of trains with scale of 1:1 is investigated using computational fluid dynamics numerical simulation method, which consists of the variation of aerodynamics force and moment with wind yaw angle, wind speed, train speed, and nose shape. After an initial validation against Baker’s results from wind tunnel test, the numerical model is then used to investigate the aerodynamic characteristics of the trains. The numerical results indicate that lift coefficient of the M train is slightly higher than TMC1 and TMC2 trains. Regardless of aerodynamics force coefficients, TMC1 reaches the maximum at a yaw angle of 75°. Aerodynamics force coefficient increases with both wind speed and train speed, but the change of which is not linear. Comparing aerodynamic force with different geometric dimensions of train nose, it is shown that height–width ratio is insensitive to side force and rolling moment, but sensitive to lift force from the yaw angle 0°–90°. The side force coefficient, as we most concern, is less than other results, when the length–width ratio is 1 and height–width is 0.87.

scholarly journals Numerical Simulation of the Anti-Icing Performance of Electric Heaters for Icing on the NACA 0012 Airfoil

Aerospace ◽  
2020 ◽  
Vol 7 (9) ◽  
pp. 123
Author(s):  
Sho Uranai ◽  
Koji Fukudome ◽  
Hiroya Mamori ◽  
Naoya Fukushima ◽  
Makoto Yamamoto
Keyword(s):  
Numerical Simulation ◽  
Lift Coefficient ◽  
Heating Surface ◽  
Leading Edge ◽  
Simulation Method ◽  
Chord Length ◽  
Ice Accretion ◽  
Suction Surface ◽  
Edge Surface ◽  
Naca 0012

Ice accretion is a phenomenon whereby super-cooled water droplets impinge and accrete on wall surfaces. It is well known that the icing may cause severe accidents via the deformation of airfoil shape and the shedding of the growing adhered ice. To prevent ice accretion, electro-thermal heaters have recently been implemented as a de- and anti-icing device for aircraft wings. In this study, an icing simulation method for a two-dimensional airfoil with a heating surface was developed by modifying the extended Messinger model. The main modification is the computation of heat transfer from the airfoil wall and the run-back water temperature achieved by the heater. A numerical simulation is conducted based on an Euler–Lagrange method: a flow field around the airfoil is computed by an Eulerian method and droplet trajectories are computed by a Lagrangian method. The wall temperature distribution was validated by experiment. The results of the numerical and practical experiments were in reasonable agreement. The ice shape and aerodynamic performance of a NACA 0012 airfoil with a heater on the leading-edge surface were computed. The heating area changed from 1% to 10% of the chord length with a four-degree angle of attack. The simulation results reveal that the lift coefficient varies significantly with the heating area: when the heating area was 1.0% of the chord length, the lift coefficient was improved by up to 15%, owing to the flow separation instigated by the ice edge; increasing the heating area, the lift coefficient deteriorated, because the suction peak on the suction surface was attenuated by the ice formed. When the heating area exceeded 4.0% of the chord length, the lift coefficient recovered by up to 4%, because the large ice near the heater vanished. In contrast, the drag coefficient gradually decreased as the heating area increased. The present simulation method using the modified extended Messinger model is more suitable for de-icing simulations of both rime and glaze ice conditions, because it reproduces the thin ice layer formed behind the heater due to the runback phenomenon.

Study on Leakage Loss Control Method of Circumferential Bending Clearance

2019 ◽  
Author(s):  
Shuai Jiang ◽  
Fu Chen ◽  
Jianyang Yu ◽  
Shaowen Chen ◽  
Yanping Song
Keyword(s):  
Control Method ◽  
Incidence Angle ◽  
Leading Edge ◽  
Blocking Effect ◽  
Field Analysis ◽  
Leakage Flow ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Control Effect ◽  
Tip Leakage

Abstract The concept of circumferential bending clearance based on Gauss Bimodal Function is proposed to suppress tip leakage flow (TLF) in a highly-loaded turbine cascade. In this method, a new vortex (BV) can be induced to mix with TLV in the middle of tip region and block the development of tip leakage vortex (TLV). Since the blocking effect divides the TLV into two parts, the tip leakage rate and loss of TLF can be reduced significantly. In order to reveal the mechanisms of blocking effect on leakage flow and its influencing factors, the research numerically investigates the effects of environmental conditions on the TLF development in a turbine cascade. The flow field analysis of the optimal bending clearance is in the first place, and then the effects of clearance heights (δ) and incidence angles (α) on the TLF characteristic and loss are investigated respectively. Results indicate that the blocking effect has a close relationship with the TLF characteristic, which can be divided into the BV migration, TLV-2 location and blocking loss. The nearer distance to the leading edge (LE) and farther distance to the suction side (SS) of BV means a less loss of TLF in bending clearance cases. The further distance away from blade tip and SS of TLV-2 means a larger-scale vortex with more loss. The additional loss in blocking region expands constantly with the increase of clearance height and incidence angle. The bending clearance has limited control effect on TLF with the variation of clearance height, especially the loss increases in Case 2%H. However, it has a strong adaptability with the change of incidence angle, the relative total pressure loss drops up to 16% in Case −5°.

New combinational active control strategy for improving aerodynamic characteristics of airfoil and rotor

2019 ◽  
Vol 234 (4) ◽  
pp. 977-996
Author(s):  
Yi-yang Ma ◽  
Qi-jun Zhao ◽  
Guo-qing Zhao
Keyword(s):  
Flow Control ◽  
Control Strategy ◽  
Active Flow Control ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Synthetic Jet ◽  
Dynamic Stall ◽  
Trailing Edge ◽  
Trailing Edge Flap ◽  
Cfd Method

In order to improve the aerodynamic characteristics of rotor, a new active flow control strategy by combining a synthetic jet actuator and a variable droop leading-edge or a trailing-edge flap has been proposed. Their control effects are numerically investigated by computational fluid dynamics (CFD) method. The validated results indicate that variable droop leading-edge and synthetic jet can suppress the formation of dynamic stall vortex and delay flow separation over rotor airfoil. Compared with the baseline state, Cdmax and Cmmax are significantly reduced. Furthermore, parametric analyses on dynamic stall control of airfoil by the combinational method are conducted, and it indicates that the aerodynamic characteristics of the oscillating rotor airfoil can be significantly improved when the non-dimensional frequency ( k*) of variable droop leading-edge is about 1.0. At last, simulations are conducted for the flow control of rotor by the combinational method. The numerical results indicate that large droop angle of variable droop leading-edge can better reduce the torque coefficient of rotor and the trailing-edge flap has the capability of increasing the thrust of rotor. Also, the synthetic jet could further improve the aerodynamic characteristics of rotor.

scholarly journals Numerical Analysis of Wind Turbine Airfoil Aerodynamic Performance with Leading Edge Bump

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Majid Asli ◽  
Behnam Mashhadi Gholamali ◽  
Abolghasem Mesgarpour Tousi
Keyword(s):  
Wind Turbine ◽  
Control Method ◽  
Flow Behavior ◽  
Renewable Energy Sources ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Vortex Generator ◽  
Leading Edge ◽  
Suction Side ◽  
Aerodynamic Performance

Aerodynamic performance improvement of wind turbine blade is the key process to improve wind turbine performance in electricity generated and energy conversion in renewable energy sources concept. The flow behavior on wind turbine blades profile and the relevant phenomena like stall can be improved by some modifications. In the present paper, Humpback Whales flippers leading edge protuberances model as a novel passive stall control method was investigated on S809 as a thick airfoil. The airfoil was numerically analyzed by CFD method in Reynolds number of 106and aerodynamic coefficients in static angle of attacks were validated with the experimental data reported by Somers in NREL. Therefore, computational results for modified airfoil with sinusoidal wavy leading edge were presented. The results revealed that, at low angles of attacks before the stall region, lift coefficient decreases slightly rather than baseline model. However, the modified airfoil has a smooth stall trend while baseline airfoil lift coefficient decreases sharply due to the separation which occurred on suction side. According to the flow physics over the airfoils, leading edge bumps act as vortex generator so vortices containing high level of momentum make the flow remain attached to the surface of the airfoil at high angle of attack and prevent it from having a deep stall.

Experimental Aerodynamic Characteristics of a Compound Wing in Ground Effect

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun Abdul Malek ◽  
Shuhaimi Mansor ◽  
Nor Azwadi Che Sidik ◽  
Agoes Priyanto
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Center Of Pressure ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Ground Clearance

Wing configuration is a parameter that affects the performance of wing-in-ground effect (WIG) craft. In this study, the aerodynamic characteristics of a new compound wing were investigated during ground effect. The compound wing was divided into three parts with a rectangular wing in the middle and two reverse taper wings with anhedral angle at the sides. The sectional profile of the wing model is NACA6409. The experiments on the compound wing and the rectangular wing were carried to examine different ground clearances, angles of attack, and Reynolds numbers. The aerodynamic coefficients of the compound wing were compared with those of the rectangular wing, which had an acceptable increase in its lift coefficient at small ground clearances, and its drag coefficient decreased compared to rectangular wing at a wide range of ground clearances, angles of attack, and Reynolds numbers. Furthermore, the lift to drag ratio of the compound wing improved considerably at small ground clearances. However, this improvement decreased at higher ground clearance. The drag polar of the compound wing showed the increment of lift coefficient versus drag coefficient was higher especially at small ground clearances. The Reynolds number had a gradual effect on lift and drag coefficients and also lift to drag of both wings. Generally, the nose down pitching moment of the compound wing was found smaller, but it was greater at high angle of attack and Reynolds number for all ground clearance. The center of pressure was closer to the leading edge of the wing in contrast to the rectangular wing. However, the center of pressure of the compound wing was later to the leading edge at high ground clearance, angle of attack, and Reynolds number.

scholarly journals Effect of Leading-Edge Bulges on Aerodynamic Characteristics of Bionic Wingsail

2021 ◽  
Author(s):  
Chen Li ◽  
Peiting Sun ◽  
Hongming Wang
Keyword(s):  
Stokes Equations ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Suction Surface ◽  
Ansys Fluent ◽  
Navier Stokes Equations ◽  
Extension Direction ◽  
Lift And Drag

The leading-edge bulges along the extension direction are designed on the marine wingsail. The height and the spanwise wavelength of the protuberances are 0.1c and 0.25c, respectively. At Reynolds number Re=5×105, the Reynolds Averaged Navier-Stokes equations are applied to the simulation of the wingsail with the bulges thanks to ANSYS Fluent finite-volume solver based on the SST K-ω models. The grid independence analysis is carried out with the lift and drag coefficients of the wingsail at AOA = 8° and AOA=20°. The results show that while the efficiency of the wingsail is reduced by devising the leading-edge bulges before stall, the bulges help to improve the lift coefficient of the wingsail when stalling. At AOA=22° under the action of the leading-edge tubercles, a convective vortex is formed on the suction surface of the modified wingsail, which reduces the flow loss. So the bulges of the wingsail can delay the stall.

Sign in / Sign up

Export Citation Format

Share Document