The Corrosion Mechanism of Cu-Containing Weathering Steel in a Cyclic Dry-Wet Condition

2009 ◽  
Vol 79-82 ◽  
pp. 957-960 ◽  
Author(s):  
Li Jie Yue ◽  
Wei Gong Chen

The weather resistance of 10CuPRE、10CuP and Q235 steels were studied by dry-wet cyclic immersion test. The corrosion resistance mechanism of rare earth Cu-containing weathering steel was studied through electrochemical polarization test, scanning electron microscope(SEM) and X ray diffraction(XRD). The results show the small and spherical rare earth oxysulfides replace the elongated MnS inclusions in the rare earth weathering steel. Less and fewer rare earth oxysulfides heavily decrease pitting susceptibility and rate of pit propagation. So the electrochemical corrosion of microarea in the steel matrix is weakened after rare earth was added in the Cu-containing weathering steel. The inner rust layer of rare earth weathering steel is more compact and uniform than that of weathering steel without rare earth. The main corrosion product on the rare earth weathering steel is α-FeOOH. The formation of the steady corrosion product is promoted by rare earth, which result in that the protective property of the inner rust layer on weathering steels is enhanced. As a result, the corrosion resistance of Cu-containing weathering steel is improved by rare earth elements.

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 517
Author(s):  
Bin Sun ◽  
Lei Cheng ◽  
Chong-Yang Du ◽  
Jing-Ke Zhang ◽  
Yong-Quan He ◽  
...  

The atmospheric corrosion behavior of a hot-rolled strip with four types (I–IV) of oxide scale was investigated using the accelerated wet–dry cycle corrosion test. Corrosion resistance and porosity of oxide scale were studied by potentiometric polarization measurements. Characterization of samples after 80 cycles of the wet–dry corrosion test showed that scale comprised wüstite and magnetite had strongest corrosion resistance. Oxide scale composed of inner magnetite/iron (>70%) and an outer magnetite layer had the weakest corrosion resistance. The corrosion kinetics (weight gain) of each type of oxide scale followed an initial linear and then parabolic (at middle to late corrosion) relationship. This could be predicted by a simple kinetic model which showed good agreement with the experimental results. Analysis of the potentiometric polarization curves, obtained from oxide coated steel electrodes, revealed that the type I oxide scale had the highest porosity, and the corrosion mechanism resulted from the joint effects of electrochemical behavior and the porosity of the oxide scale. In the initial stage of corrosion, the corrosion product nucleated and an outer rust layer formed. As the thickness of outer rust layer increased, the corrosion product developed on the scale defects. An inner rust layer then formed in the localized pits as crack growth of the scale. This attacked the scale and expanded into the substrate during the later stage of corrosion. At this stage, the protective effect of the oxide scale was lost.


2013 ◽  
Vol 734-737 ◽  
pp. 2332-2337
Author(s):  
Rui Hua Guo ◽  
Fang Sheng Liu ◽  
Lin Min Wang

This article by orthogonal experimental method to determine the composition of chromate conversion and use of electrochemical method of electrochemical corrosion of the film discussed the substrate in different components, content, time and pH of chromate conversion coating of corrosion resistance. Orthogonal to determine the best experimental chromate conversion solution by adding the rare earth element cerium and lanthanum salt, and discuss the effects of rare earth elements cerium and lanthanum chromate conversion film on the anti-corrosion. The results show that in CrO3 5.4 g/L, NaF 0.5 g/L, K3Fe (CN)6 0.5 g/L, pH 1, conversion time is three minutes, there is a better corrosion resistance. The rare earth elements in a chromate conversion solution, La2(CO3)3 to 0.2 g/L chromate conversion coating of the anti-corrosion better.


2019 ◽  
Vol 66 (5) ◽  
pp. 565-572
Author(s):  
Xiaoxiao Liu ◽  
Dejun Kong

Purpose This study aims to investigate the salt spray corrosion (SSC) and electrochemical corrosion of obtained Zn–Al coating, which provided a basis for comprehensive analysis of corrosion behavior of Zn–Al coating. Design/methodology/approach A Zn–Al coating was fabricated on Q235A steel using a Dacromet method. The SSC and electrochemical corrosion performances in 3.5 Wt.% NaCl solution were investigated using an SSC chamber and electrochemical workstation, respectively, and the corrosion mechanism of Zn–Al coating was discussed. Findings The Dacromet fabricated Zn–Al coating is primarily composed of Zn and Al phases, its residual stress of −11.1 ± 4 MPa is compressive stress, which is beneficial to improve its corrosion resistance. In the SSC process, the corrosion product of Zn5(OH)8Cl2H2O enhances the corrosion resistance of Zn–Al coating, which provides sufficient cathodic protection for the substrate. The corrosion potential of Zn–Al coating is lower than that of substrate, which provides sufficient cathodic protection to the substrate, the Zn–Al coating in the immersion periods is protected by the corrosion product and Zn–Al sheets. Originality/value In this study, a Zn–Al coating was first fabricated on Q235A steel using a Dacromet method.


2013 ◽  
Vol 634-638 ◽  
pp. 1698-1703
Author(s):  
Yan Feng Zhou ◽  
Wei Jian Qiu ◽  
Wei Xiao Li ◽  
Jiang Xie

The corrosion process of rare earth (RE) SPCC steel and SPCC steel in CSP in 3.5% NaCl solutions was investigated by SEM, EDS, XRD and polarization curve measurements. The results show that grain refinement can be obtained, the inclusions will be formed, and the electrochemical corrosion of microscopic region is weakened and therefore the corrosion resistance of SPCC steel could be improved by addition of RE. The rust layer of RE treated steel generated in the solution is more compact, the α-FeOOH content in rust layer is higher, and the content of activated γ-FeOOH and β-FeOOH is smaller, which are helpful to protect the steel. It also shows that current densities of SPCC steel is lower and the corrosive tendency will decrease with the addition of RE, which also makes the corrosion resistance of steel improved.


2019 ◽  
Vol 66 (3) ◽  
pp. 352-359
Author(s):  
Li Jiahong ◽  
Kong Dejun

Purpose The purpose of this paper is to improve the salt spray corrosion and electrochemical corrosion performances of H13 hot work mould steel, Cr–Ni coatings with the different Cr and Ni mass ratios are fabricated using a laser cladding (LC), which provides an experimental basis for the surface modification treatment of H13 steel. Design/methodology/approach Cr–Ni coatings with the different Cr and Ni mass ratios were firstly fabricated on H13 hot work mould steel using a laser cladding (LC). The salt spray corrosion (SSC) and electrochemical corrosion performances of Cr–Ni coatings in 3.5 Wt.% NaCl solution were investigated to analyze the corrosion mechanism, and the effect of mass ratios of Cr and Ni on their corrosion mechanism was discussed. Findings The laser cladded Cr–Ni coatings with the different Cr and Ni mass ratios are composed of Cr–Ni compounds, which are metallurgically combined with the substrate. The SSC resistance of Cr–Ni coating with the Cr and Ni mass ratios of 24:76 is the highest. The electrochemical corrosion resistance of Cr–Ni coating with the Cr and Ni mass ratio of 24:76 is the best among the three kinds of coatings. Originality/value In this study, the corrosion resistance of laser cladded Cr–Ni coatings with the Cr and Ni mass ratios of 17: 83, 20: 80 and 24: 76 was first evaluated using salt spray corrosion (SSC) and electrochemical tests, and the effect of mass ratios of Cr and Ni on their corrosion mechanism was discussed.


2009 ◽  
Vol 79-82 ◽  
pp. 1075-1078
Author(s):  
Nai Ming Lin ◽  
Fa Qin Xie ◽  
Tao Zhong ◽  
Xiang Qing Wu ◽  
Wei Tian

The rare earth (RE) modified chromizing coating was obtained on P110 oil casing tube steel (P110 steel) substrate by means of pack cementation technique to enhance the resistance against corrosion of P110 steel. Scanning Electron Microscopy (SEM), Energy Dispersive X-ray analysis (EDX) and X-ray diffraction (XRD) were employed to research microstructure, composition distribution and phase constitution of the chromizing coating. The effect of minor addition of RE on the microstructure of chromizing was discussed. Corrosion resistance of chromizing coating was investigated and compared with that of bare P110 steel via electrochemical corrosion and immersion corrosion in simulated oilfield brine solution, respectively. The results showed that a uniform, continuous and compact coating was formed on P110 steel. The coating with RE addition was more compact than that of the coating added no RE, and a small amount of RE addition could promote the chromizing procedure notably. From SEM and EDX investigation, it had been confirmed that the coating was composed of two different layers, an out layer and an inner layer; the coating mainly contains Fe and Cr; the concentration of Cr decreased as the distance from the surface increased, yet Fe presented the inverse trend. XRD analysis indicated the coating was built up by (Cr, Fe)23C6 referring to the out layer, (Cr, Fe)7C3, Cr7C3 and α-(Cr, Fe) corresponding to the inner layer. Electrochemical corrosion consequence was obtained as follows: the self-corroding electric potential of chromizing coating was higher, and the corrosion current density was lower than that of bare P110 steel, which revealed that chromizing coating had better anti-corrosion performance; immersion corrosion results demonstrated the mass loss of chromized P110 steel was lower, and this meant that chromizing coating had a better corrosion resistance than that of bare P110 steel on the experimental condition. A compact (Cr, Fe)xCy coating can be fabricated by pack cementation technique. As a result of minor RE addition, microstructure and corrosion resistance of the chromizing coating are improved obviously.


2021 ◽  
Vol 2101 (1) ◽  
pp. 012058
Author(s):  
J P Xin ◽  
S Y Zhang ◽  
S P Hu

Abstract Using a combination of first-principles calculations and experimental studies to study the effect of La on the corrosion resistance of Powder sherardizing layer in metal structures. Compared to other sherardizing rare earth elements (Re), La has better adsorption with the iron matrix and has the lowest binding energy on the adsorption surface (111) of the Fe matrix. Therefore, the rare earth element La is added to the powder sherardizing process for the rare earth chemical heat treatment to reduce the defects of the powder sherardizing faults formed, improve the surface uniformity and the quality of the permeation layer. On the basis of calculation, La element was added in the process of powder sherardizing, and the corrosion performance of the formed powder galvanizing layer was studied. After alternating salt spray experiments, the degree of corrosion of the layer is relatively small and the corrosion products are predominantly layered and spherical. Electrochemical tests of the layer show that the corrosion resistance of the layer after the rare earth chemical heat treatment has improved.


2015 ◽  
Vol 816 ◽  
pp. 781-787
Author(s):  
Z.R. Hou ◽  
H.L. Yi ◽  
X.M. Zhao

Based on the 355MPa high weather-resistant steel, three different kinds of high weather-resistant steels were designed by varying the content of Ni. The the corrosion resistance of the high weather-resistant steel as well as the influence of Ni content on the corrosion resistance were studied in the present investigation. The results of the cycle corrosion tests indicated that with the addition of Ni, the corrosion resistance was improved to some extent. The rust layer of the weathering steel was composed of α-FeOOH and γ-FeOOH at the beginning of corrosion, and the α-FeOOH turned to γ-FeOOH which enhanced the corrosion resistance.


2012 ◽  
Vol 479-481 ◽  
pp. 574-577
Author(s):  
Zhi Fen Wang ◽  
Jian Rong Liu ◽  
Li Xin Wu ◽  
Hai E Huang ◽  
Qian Xue Zhou

The weatherability of a weathering steel W450QN was compared with a carbon steel Q345 after 5 years atmospheric corrosion. The results indicated that the corrosion resistance was better for W450QN than Q345 based on the corrosion rate. The characteristics of the rust layers indicated the rust layer on W450QN was denser and thicker than that of Q345. The rust layers were mainly composed of goethite (α-FeOOH) with a few of lepidocrocite (γ-FeOOH). W450QN had better weatherability attributed to the alloying elements of copper, chromium and phosphorus enriched in the rust layer.


Sign in / Sign up

Export Citation Format

Share Document