Manufacturing of MWNT Filled Carbon Fiber Reinforced Polypropylene with Gelatin

2013 ◽  
Vol 845 ◽  
pp. 868-872
Author(s):  
Jeong U. Roh ◽  
Woo I. Lee
Keyword(s):  
Shear Strength ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Composite Layer ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
Ultimate Shear Strength ◽  
Iosipescu Shear Test ◽  
Coated Carbon ◽  
Morphology Of Surface

The aims of this study were to investigate the effect of gelatin coating on the mechanical property of the polypropylene (PP) composites by the addition of Multi-walled nanotube (MWNT) and gelatin coated carbon fibers. The morphology of surface of carbon fiber filament on the fracture surface was examined by field-emission scanning electronic microscopy (FE-SEM). The Iosipescu shear test was done to determine the ultimate shear strength of the PP reinforced with MWNT/gelatin composite layer coated carbon fibers. The gelatin coated carbon fibers resulted in an increase in the ultimate shear strength compared to plain carbon fibers. In addition, the ultimate shear strength was improved through the addition of MWNTs with the gelatin. Also, with gelatin acting as a binder, flying CNT particles could be minimized.

Surface and Composite Interface of Carbon Fiber Modified by Grafting of Diethanolamine

2009 ◽  
Vol 79-82 ◽  
pp. 497-500 ◽  
Author(s):  
Lei Chen ◽  
Zhi Wei Xu ◽  
Jia Lu Li ◽  
Xiao Qing Wu ◽  
Li Chen
Keyword(s):  
Shear Strength ◽  
Carbon Fiber ◽  
Functional Groups ◽  
Carbon Fibers ◽  
Irradiation Dose ◽  
Interlaminar Shear Strength ◽  
Epoxy Composites ◽  
Composite Interface ◽  
Γ Ray ◽  
Interlaminar Shear

The γ-ray co-irradiation method was employed to study the effect of diethanolamine modification on the surface of carbon fiber (CF) and the interfacial properties of CF/epoxy composites. Compared with the original carbon fiber, the surface of modified fibers became rougher. The amount of oxygen-containing functional groups was increased and the nitrogen element was detected after irradiation grafting. The interlaminar shear strength (ILSS) of composites reinforced by carbon fibers irradiated in diethanolamine solution was increased and then decreased as the irradiation dose increased. The ILSS of CF/epoxy composites was enhanced by 16.1% at 200kGy dose, compared with that of untreated one. The γ-ray irradiation grafting is expected to be a promising method for the industrialized modification of carbon fibers.

scholarly journals CoMnO2-Decorated Polyimide-Based Carbon Fiber Electrodes for Wire-Type Asymmetric Supercapacitor Applications

2020 ◽  
Author(s):  
Young-Hun Cho ◽  
Jae-Gyoung Seong ◽  
Jae-Hyun Noh ◽  
Da-Young Kim ◽  
Yong-Sik Chung ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Carbon Fibers ◽  
Rate Capability ◽  
Ammonium Persulfate ◽  
Chemical Oxidation ◽  
Sem Analysis ◽  
Metal Nanostructures ◽  
Carbon Fiber Electrode ◽  
Coated Carbon ◽  
Fiber Electrode

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

Influence of different surface-coated carbon fibers on the properties of the poly(phenylene sulfide) composites

2018 ◽  
Vol 53 (8) ◽  
pp. 1123-1132 ◽  
Author(s):  
Bedriye Ucpinar ◽  
Ayse Aytac
Keyword(s):  
Differential Scanning Calorimetry ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Mechanical Analysis ◽  
Fiber Reinforced ◽  
Scanning Calorimetry ◽  
Carbon Fiber Reinforced ◽  
Coated Carbon ◽  
Scanning Electron ◽  
Phenylene Sulfide

This paper aims to study the effect of different surface coatings of carbon fiber on the thermal, mechanical, and morphological properties of carbon fiber reinforced poly(phenylene sulfide) composites. To this end, unsized and different surface-coated carbon fibers were used. Prepared poly(phenylene sulfide)/carbon fiber composites were characterized by using Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, tensile test, dynamic mechanical analysis, and scanning electron microscopy. Tensile strength values of the surfaced-coated carbon fibers reinforced poly(phenylene sulfide) composites are higher than the unsized carbon fiber reinforced poly(phenylene sulfide) composite. The highest tensile strength and modulus values were observed for the polyurethane-coated carbon fiber reinforcement. Dynamic mechanical analysis studies indicated that polyurethane-coated carbon fiber reinforced composite exhibited higher storage modulus and better adhesion than the others. Differential scanning calorimetry results show that melting and glass transition temperature of the composites did not change significantly. Scanning electron microscopic studies showed that polyurethane and epoxy-coated carbon fibers exhibited better adhesion with poly(phenylene sulfide).

Research on the Friction and Wear Properties of the Copper Matrix Composites Reinforced with Copperized Carbon Fibers

2014 ◽  
Vol 556-562 ◽  
pp. 624-627 ◽  
Author(s):  
Ran Xu ◽  
Yong Wang ◽  
Run Hong Liu ◽  
Hao Zou
Keyword(s):  
Carbon Fiber ◽  
Carbon Fibers ◽  
Friction And Wear ◽  
Testing Machine ◽  
Copper Matrix ◽  
Wear Testing ◽  
Wear Property ◽  
Vacuum Sintering ◽  
Graphite Composites ◽  
Coated Carbon

The aim of this paper is to develop a kind of copper matrix self-lubricious material with excellent friction and wear characteristics. The copper-graphite composites reinforced with short copper-coated carbon fibers (CF-C/Cu) were successfully developed using techniques of mechanical alloying, composite plating and hot press vacuum sintering. For comparison, copper-graphite composites without short copper-coated carbon fibers (C/Cu) were made under the same process. The wear testing was carried out using a rapid wear testing machine (M-200).Friction coefficient was measured by a micro-wear tester (UMT).The microstructure, abrasive dust and worn surface of the wear pins on the different condition such as load and wear time were examined by SEM. It was noted that the addition of copper-coated carbon fiber in the Cu-based composites can retard the transformation process which transforms from micro-cutting wear to adhesive wear and delamination. The abrasion loss of the composites with short copper-coated carbon fibers appeared a valley when the load increased from 10N to 30N. It showed that the addition of copper-coated carbon fiber enhanced the anti-friction and anti-wear property of copper matrix composite and better than the sample without carbon fibers.

Preparation of the Carbon Fiber/Cu Alloy Matrix Self-Lubricating Composite Materials

2014 ◽  
Vol 670-671 ◽  
pp. 164-167 ◽  
Author(s):  
Sui Yuan Chen ◽  
Xin Rong Li ◽  
Yu Ning Bi ◽  
Daniel Wellburn ◽  
Jing Liang ◽  
...  
Keyword(s):  
Composite Materials ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Matrix Alloy ◽  
Copper Matrix ◽  
Wear Properties ◽  
Alloy Matrix ◽  
Coated Carbon

Using 663-tin bronze, Ni, W, nanoAl2O3, MoS2, graphite, CaF2, and Ni coated graphite as the matrix alloy powder, in which copper-coated carbon fiber of 5%, 7%, 9%, 11% and 13% in volume fraction were added as the reinforcing phase, a novel type carbon fiber/copper-matrix self-lubricating composite materials was prepared by means of powder metallurgy. The results indicate that the mechanical properties of the composite materials are improved after adding copper-coated carbon fibers. The composite materials reach optimal overall mechanical performance under testing when the volume fraction of the added copper-coated carbon fibers is 11%.: with a hardness of 57.8 HV and a compressive strength of 222 MPa. The addition of carbon fiber also improved the friction and wear properties of the composite materials. Increasing the volume fraction of fiber, was found to increase the wear resistance and improve self-lubricating performance. A volume fraction of 11% gave a friction coefficient of 0.09 and abrasion loss of 4mg.

scholarly journals Wettability of Copper Coated Carbon Fibers

1994 ◽  
Vol 3 (4) ◽  
pp. 096369359400300
Author(s):  
G. Carotenuto ◽  
A. Gallo ◽  
L. Nicolais
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Solid Surface ◽  
Fiber Surface ◽  
Wetting Kinetics ◽  
Coated Carbon ◽  
Kinetics Of ◽  
Scanning Electron

The wetting kinetics of a solid surface by a molten metal decrease with increase of its roughness. The topography of the growing copper coating, produced on carbon fiber surface by electroplating from a sulphat bath, has been studied by scanning electron microscopy. The smoothes surface is produced after 200÷300 milliampere-hour of plating.

scholarly journals Mechanical Properties of SiO2-Coated Carbon Fiber-Reinforced Mortar Composites with Different Fiber Lengths and Fiber Volume Fractions

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Gwang-Hee Heo ◽  
Jong-Gun Park ◽  
Ki-Chang Song ◽  
Jong-Ho Park ◽  
Hyung-Min Jun
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Flexural Strength ◽  
Carbon Fibers ◽  
Cement Matrix ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions ◽  
Carbon Fiber Reinforced ◽  
Coated Carbon

In the present study, SiO2 particles were coated on the surface of carbon fibers by means of chemical reaction of silane coupling agent (glycidoxypropyl trimethoxysilane, GPTMS) and colloidal SiO2 sol to improve the interfacial bonding force between fibers and matrix in cement matrix. The surface of the modified carbon fibers was confirmed through a scanning electron microscope (SEM). The mechanical properties of SiO2-coated carbon fiber mortar and uncoated carbon fiber mortar with different fiber lengths (6 mm and 12 mm) and fiber volume fractions (0.5%, 1.0%, 1.5%, and 2.0%) were compared and analyzed. The experimental results show that the flow values of the carbon fiber mortar were greatly disadvantageous in terms of fluidity due to the nonhydrophilicity of fibers and fiber balls, and the unit weight decreased significantly as the fiber volume fractions increased. However, the air content increased more or less. In addition, regardless of whether the fibers were coated, the compressive strength of carbon fiber-reinforced mortar (CFRM) composite specimens tended to gradually decrease as the fiber volume fractions increased. On the other hand, in case of the SiO2-coated CFRM composite specimens, the flexural strength was significantly increased compared to uncoated CFRM composite specimens and plain mortar specimens, and the highest flexural strength was obtained at 12 mm and 1.5%, particularly. It can be seen that the new carbon fiber surface modification method employed in this study was very effective in enhancing the flexural strength as cement-reinforcing materials.

Sign in / Sign up

Export Citation Format

Share Document