Seismic Performance Evaluation of Residential Structures in Egypt

2014 ◽  
Vol 919-921 ◽  
pp. 945-950
Author(s):  
Yasser E. Ibrahim ◽  
Osman Shallan ◽  
Ashraf Elshihy ◽  
Mohamed Selim
Keyword(s):  
Fragility Curves ◽  
Ground Motions ◽  
Three Dimensional ◽  
Structural Models ◽  
Incremental Dynamic Analysis ◽  
Reinforced Concrete Structures ◽  
Seismic Loads ◽  
Seismic Performance Evaluation ◽  
Existing Structures ◽  
Operational Life

In this research, analytical fragility curves for three existing structures are presented. Structures are 2-story, 6-story and 10-story residential reinforced concrete structures designed under dead ,live and seismic loads of zone 3 according to Egyptian code (2008). The design acceleration is 0.15g. The fragility curves are developed based on nonlinear incremental dynamic analysis of three dimensional structural models using SeismoStruct under twelve historic ground motions. Four performance levels are considered; fully operational, operational, life safe and near collapse.

Seismic Fragilities of High-Voltage Substation Disconnect Switches

2019 ◽  
Vol 35 (4) ◽  
pp. 1559-1582
Author(s):  
Bai Wen ◽  
Mohamed A. Moustafa ◽  
Dai Junwu
Keyword(s):  
Seismic Vulnerability ◽  
Fragility Curves ◽  
Ground Motions ◽  
Incremental Dynamic Analysis ◽  
Nonlinear Finite Element ◽  
Power Grids ◽  
Finite Element Models ◽  
Severe Damage ◽  
Substation Equipment ◽  
Motion Characteristics

Electrical substations and vital components, e.g., disconnect switches, experienced severe damage that caused blackouts during past earthquakes. To improve the seismic resiliency of power grids and use probabilistic decision-making frameworks, comprehensive fragility data for the different substation equipment are needed. The objective of this study is to investigate the seismic performance of and develop component and system fragility curves for a critical substation component: disconnect switches. The seismic vulnerability of two common switch types was evaluated and two operational configurations were considered. Detailed nonlinear finite element models for the full switches were calibrated using previous experimental data and used to conduct incremental dynamic analysis and carry out the fragility assessment. A total of 160 triaxial ground motions representing four sets of different ground motion characteristics were used. The switches’ fragility curves were developed and presented to be readily used for new substation design, prioritizing retrofit/maintenance activities and reliability assessment of power grids.

Seismic Fragility Analysis of the Smithsonian Institute Museum Support Center

2017 ◽  
Vol 33 (1) ◽  
pp. 85-108 ◽  
Author(s):  
Xin Chu ◽  
James M. Ricles ◽  
Shamim N. Pakzad
Keyword(s):  
Structural Damage ◽  
Fragility Curves ◽  
Ground Motions ◽  
Three Dimensional ◽  
Element Model ◽  
Seismic Fragility ◽  
Design Basis ◽  
Virginia Earthquake ◽  
Smithsonian Institute ◽  
Hazard Levels

This paper presents the seismic fragility assessment of the Smithsonian Institute Museum Support Center (MSC), which sustained appreciable damage during the 2011 Virginia earthquake. A three-dimensional (3-D) finite element model (FEM) for the building was created and validated using measured dynamic characteristics determined from field vibration test data. Two suites of bidirectional ground motions at different hazard levels were applied to the FEM to generate fragility curves for structural as well as nonstructural (storage cabinets) damage. The effect of brace yielding strength on structural and nonstructural damage is also investigated to provide recommendations for future retrofit. The fragility curves show that the spectral acceleration to cause structural damage to the building is not high. Due to low seismicity, however, the probability for the structure to be damaged at the design basis earthquake is small. Nevertheless, the probability for nonstructural damage is considerable, which is an important issue related to the seismic performance of the building.

scholarly journals Bidirectional Energy-based Pushover Procedure as a Fast Approach to Establish Approximate IDA Curves under Biaxial Seismic Excitations: An Evaluation for Medium- and High-rise Buildings

2021 ◽  
Author(s):  
Sahman Soleimani ◽  
Abdolreza Sarvghad Moghadam ◽  
Armin Aziminejad
Keyword(s):  
Dynamic Analysis ◽  
Ground Motions ◽  
Structural Models ◽  
Incremental Dynamic Analysis ◽  
Seismic Excitations ◽  
High Rise ◽  
Asymmetric Buildings ◽  
Fast Approach ◽  
Unique Approach ◽  
Similar Accuracy

Abstract Bidirectional energy-based pushover (BEP) procedure is expanded in this paper to predict approximate incremental dynamic analysis (IDA) results of medium- and high-rise structures. BEP is a unique approach in the sense that it provides approximate IDA curves under the simultaneous effect of two horizontal components of ground motions and is applicable to both symmetric- and asymmetric-plan buildings. The method has already proved to be useful in low-rise buildings, and this study aims to evaluate its suitability for mid- and high-rise structures. Six structural models were considered in this evaluation in two groups of 9- and 20-story buildings, with each group consisting of a symmetric, a one-way asymmetric, and a two-way asymmetric-plan building. The results revealed that the method was sufficiently accurate to provide approximate IDA curves for all structural models. The method had similar accuracy in the asymmetric models as it did in the symmetric models, although the accuracy slightly decreased as the height of the building increased. BEP also provided good estimates of the demands in both ‘flexible’ and ‘stiff sides’ of the asymmetric buildings as well as the demands over the height of the buildings.

Tunnel performance during the Puebla-Mexico 19 September 2017 earthquake

2020 ◽  
Vol 36 (2_suppl) ◽  
pp. 288-313
Author(s):  
Juan M Mayoral ◽  
Gilberto Mosqueda ◽  
Daniel De La Rosa ◽  
Mauricio Alcaraz
Keyword(s):  
Mexico City ◽  
Seismic Performance ◽  
Urban Areas ◽  
Numerical Study ◽  
Three Dimensional ◽  
Frequency Content ◽  
Seismic Performance Evaluation ◽  
Ground Deformations ◽  
Under Construction ◽  
Observed Damage

Seismic performance of tunnels during earthquakes in densely populated areas requires assessing complex interactions with existing infrastructure such as bridges, urban overpasses, and metro stations, including low- to medium-rise buildings. This article presents the numerical study of an instrumented tunnel, currently under construction on stiff soils, located in the western part of Mexico City, during the Puebla-Mexico 19 September 2017 earthquake. Three-dimensional finite difference models were developed using the software FLAC3D. Initially, the static response of the tunnel was evaluated accounting for the excavation technique. Then, the seismic performance evaluation of the tunnel was carried out, computing ground deformations and factors of safety, considering soil nonlinearities. Good agreement was observed between predicted and observed damage during post-event site observations. Once the soundness of the numerical model was established, a numerical study was undertaken to investigate the effect of frequency content in tunnel-induced ground motion incoherence for tunnels built in cemented stiff soils. A series of strong ground motions recorded during normal and subduction events were used in the simulations, considering a return period of 250 years, as recommended in the Mexico City building code. From the results, it was concluded that the tunnel presence leads to important frequency content modification in the tunnel surroundings which can affect low- to mid-rise stiff structures located nearby. This important finding must be taken into account when assessing the seismic risk in highly populated urban areas, such as Mexico City.

scholarly journals Computer-aided design of multi-purpose steel headframes for mines with a new technical level

2020 ◽  
Vol 174 ◽  
pp. 01048
Author(s):  
Elena Kassikhina ◽  
Vladimir Pershin ◽  
Nina Rusakova
Keyword(s):  
Cross Sections ◽  
Computer Aided Design ◽  
Information Technologies ◽  
Three Dimensional ◽  
Numerical Control ◽  
Technical Level ◽  
Resource Saving ◽  
Existing Structures ◽  
Set Up ◽  
Aided Design

The existing structures of the steel sinking headgear and permanent headframe do not meet the requirements of resource saving (metal consumption and manpower input at installation), and the present methods of the headframe designing do not fully reflect recent possibilities of applying of the advanced information technologies. Technical level of the modern software makes it possible for designers to set up multiple numerical experiments to create a computer simulation that allows solving the problem without field and laboratory experiments, and therefore without special costs. In this regard, a mathematical simulation has been developed and based on it, software to select cross-sections of multi- purpose steel headframe elements and to calculate proper weight of its metal structures depending on the characteristics and hoisting equipment. A headframe drawing is displayed, as the results of the software work, including list of elements, obtained optimal hoisting equipment in accordance with the initial data. The software allows speeding up graphic work and reducing manpower input on calculations and paper work. The software allows developing a three-dimensional image of the structure and its functional blocks, based on the obtained initial parameters, as well as developing control software for units with numerical control (NC) in order to manufacture multi-purpose headframes.

SEISMIC RESPONSE OF POWER TRANSMISSION TOWER-LINE SYSTEM UNDER MULTI-COMPONENT MULTI-SUPPORT EXCITATIONS

2012 ◽  
Vol 06 (04) ◽  
pp. 1250025 ◽  
Author(s):  
TIAN LI ◽  
LI HONGNAN ◽  
LIU GUOHUAN
Keyword(s):  
Seismic Waves ◽  
Power Transmission ◽  
Incident Angle ◽  
Ground Motions ◽  
Three Dimensional ◽  
Transmission Tower ◽  
Line System ◽  
Time Stepping ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The effect of multi-component multi-support excitations on the response of power transmission tower-line system is analyzed in this paper, using three-dimensional finite element time-stepping analysis of a transmission tower-line system based on an actual project. Multi-component multi-support earthquake input waves are generated based on the Code for Design of Seismic of Electrical Installations. Geometric non-linearity was considered in the analysis. An extensive parametric study was conducted to investigate the behavior of the transmission tower-line system under multi-component multi-support seismic excitations. The parameters include single-component multi-support ground motions, multi-component multi-support ground motions, the correlations among the three-component of multi-component multi-support ground motions, the spatial correlation of multi-component multi-support ground motions, the incident angle of multi-component multi-support seismic waves, the ratio of the peak values of the three-component of multi-component multi-support ground motions, and site condition with apparent wave velocity of multi-component multi-support ground motions.

Sign in / Sign up

Export Citation Format

Share Document