Experiments on Inverse Method to Illumination by Optimization Technique IMIbyOPTIM with Fixed Light Source Power

2014 ◽  
Vol 348 ◽  
pp. 216-225
Author(s):  
Letícia Jenisch Rodrigues ◽  
Tiago Haubert Andriotty ◽  
Paulo Smith Schneider ◽  
Francis Henrique Ramos França
Keyword(s):  
Light Source ◽  
Inverse Method ◽  
Optimization Technique ◽  
Source Distribution ◽  
Light Sources ◽  
Source Power ◽  
Experimental Procedure ◽  
Broad Variety ◽  
Particular Solution ◽  
Free Placement

The present work reports an experimental procedure designed to validate a particular solution for the distribution of artificial light sources in the sealing of an enclosure obtained by the inverse method IMIbyOPTIM. An illumination design assuming the free placement of purely diffuse light sources aims to generate a uniform illumination field on a work plane. A reduced scale enclosure is built to validate the method effectiveness, by comparing the experimental results to an illuminance target. An equally non-optimized light source distribution is placed on the enclosure and measurements confirm the hypothesis of distortion of the illumination field, already predicted by simulations. After the optimization of the light sources distribution, the measured illumination field becomes closer to the dimensionless unitary target, with a standard deviation of less than 0.021. This particular experiment verifies IMIbyOPTIM predictions and allows continuing the validation process of the method for a broad variety of design combinations.

Organic Light Emitting Diodes - Innovative Light Sources

2019 ◽  
pp. 101-107
Author(s):  
Sergei A. Stakharny
Keyword(s):  
Light Source ◽  
Organic Light Emitting Diodes ◽  
Organic Leds ◽  
Light Sources ◽  
High Quality ◽  
Light Emitting ◽  
Organic Light ◽  
Lighting Systems ◽  
Physical Principles ◽  
Prospects Of Application

This article is a review of the new light source – organic LEDs having prospects of application in general and special lighting systems. The article describes physical principles of operation of organic LEDs, their advantages and principal differences from conventional non-organic LEDs and other light sources. Also the article devoted to contemporary achievements and prospects of development of this field in the spheres of both general and museum lighting as well as other spheres where properties of organic LEDs as high-quality light sources may be extremely useful.

Relationship between Faithfulness and Preference of Stars in a Planetarium

2019 ◽  
Vol 2 (1) ◽  
pp. 10402-1-10402-11
Author(s):  
Midori Tanaka ◽  
Takahiko Horiuchi ◽  
Ken’ichi Otani
Keyword(s):  
Light Source ◽  
Preference Rating ◽  
Experimental Procedure ◽  
Male And Female ◽  
Astronomical Observations ◽  
Low Luminance ◽  
Projection Pattern ◽  
The Relationship ◽  
Star Field

Abstract A planetarium imitates a starry sky with physical and technical limitations using a dome, projector, and light source. It is widely used for entertainment, and astronomy and physics educations. In our previous study, we investigated the evaluation for faithful reproduction of a star field in a planetarium by performing psychometric experiments with 20 observers for plural projection patterns with different reproduction factors (color, luminance, and size of projected stars). In this study, we investigate the relationship between faithfulness and preference of a star field in a planetarium through a psychometric experiment with 47 observers. The experimental procedure followed the previous study. The rating of faithfulness improved for the projection pattern with a smaller star size. For the preference evaluation, the projection pattern with low luminance significantly lowered the preference rating. The results of the experiment indicate that the preferable star reproduction was different between male and female observers, whereas the faithful star reproduction was not significantly different in the evaluations between male and female observers. The male observers sought a faithful star reproduction as the preferred reproduction. In contrast, the female observers did not feel the faithful star reproduction preferable, and evaluated the more brilliant star reproduction as the preferred reproduction. These results were not dependent on the experience in astronomical observations.

scholarly journals Analysis on High-Power Seaport LED Luminaire with Uniform Light Distribution Based on Optimized Lens and Heatsink

2021 ◽  
Vol 11 (9) ◽  
pp. 4035
Author(s):  
Jinsheon Kim ◽  
Jeungmo Kang ◽  
Woojin Jang
Keyword(s):  
Light Source ◽  
High Power ◽  
Heat Dissipation ◽  
Light Emitting Diode ◽  
Light Distribution ◽  
Light Sources ◽  
Led Light ◽  
High Power Led ◽  
Distribution Requirement ◽  
Lighting Application

In the case of light-emitting diode (LED) seaport luminaires, they should be designed in consideration of glare, average illuminance, and overall uniformity. Although it is possible to implement light distribution through auxiliary devices such as reflectors, it means increasing the weight and size of the luminaire, which reduces the feasibility. Considering the special environment of seaport luminaires, which are installed at a height of 30 m or more, it is necessary to reduce the weight of the device, facilitate replacement, and secure a light source with a long life. In this paper, an optimized lens design was investigated to provide uniform light distribution to meet the requirement in the seaport lighting application. Four types of lens were designed and fabricated to verify the uniform light distribution requirement for the seaport lighting application. Using numerical analysis, we optimized the lens that provides the required minimum overall uniformity for the seaport lighting application. A theoretical analysis for the heatsink structure and shape were conducted to reduce the heat from the high-power LED light sources up to 250 W. As a result of these analyses on the heat dissipation characteristics of the high-power LED light source used in the LED seaport luminaire, the heatsink with hexagonal-shape fins shows the best heat dissipation effect. Finally, a prototype LED seaport luminaire with an optimized lens and heat sink was fabricated and tested in a real seaport environment. The light distribution characteristics of this prototype LED seaport luminaire were compared with a commercial high-pressure sodium luminaire and metal halide luminaire.

scholarly journals Load Frequency Control Using Hybrid Intelligent Optimization Technique for Multi-Source Power Systems

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1581
Author(s):  
Deepak Kumar Gupta ◽  
Amitkumar V. Jha ◽  
Bhargav Appasani ◽  
Avireni Srinivasulu ◽  
Nicu Bizon ◽  
...  
Keyword(s):  
Power Plant ◽  
Power System ◽  
Frequency Control ◽  
Optimization Technique ◽  
Load Frequency Control ◽  
Frequency Deviation ◽  
Source Power ◽  
Load Frequency ◽  
Tie Line

The automatic load frequency control for multi-area power systems has been a challenging task for power system engineers. The complexity of this task further increases with the incorporation of multiple sources of power generation. For multi-source power system, this paper presents a new heuristic-based hybrid optimization technique to achieve the objective of automatic load frequency control. In particular, the proposed optimization technique regulates the frequency deviation and the tie-line power in multi-source power system. The proposed optimization technique uses the main features of three different optimization techniques, namely, the Firefly Algorithm (FA), the Particle Swarm Optimization (PSO), and the Gravitational Search Algorithm (GSA). The proposed algorithm was used to tune the parameters of a Proportional Integral Derivative (PID) controller to achieve the automatic load frequency control of the multi-source power system. The integral time absolute error was used as the objective function. Moreover, the controller was also tuned to ensure that the tie-line power and the frequency of the multi-source power system were within the acceptable limits. A two-area power system was designed using MATLAB-Simulink tool, consisting of three types of power sources, viz., thermal power plant, hydro power plant, and gas-turbine power plant. The overall efficacy of the proposed algorithm was tested for two different case studies. In the first case study, both the areas were subjected to a load increment of 0.01 p.u. In the second case, the two areas were subjected to different load increments of 0.03 p.u and 0.02 p.u, respectively. Furthermore, the settling time and the peak overshoot were considered to measure the effect on the frequency deviation and on the tie-line response. For the first case study, the settling times for the frequency deviation in area-1, the frequency deviation in area-2, and the tie-line power flow were 8.5 s, 5.5 s, and 3.0 s, respectively. In comparison, these values were 8.7 s, 6.1 s, and 5.5 s, using PSO; 8.7 s, 7.2 s, and 6.5 s, using FA; and 9.0 s, 8.0 s, and 11.0 s using GSA. Similarly, for case study II, these values were: 5.5 s, 5.6 s, and 5.1 s, using the proposed algorithm; 6.2 s, 6.3 s, and 5.3 s, using PSO; 7.0 s, 6.5 s, and 10.0 s, using FA; and 8.5 s, 7.5 s, and 12.0 s, using GSA. Thus, the proposed algorithm performed better than the other techniques.

scholarly journals Towards the Optimum Light Source Spectrum

2010 ◽  
Vol 2010 ◽  
pp. 1-9 ◽  
Author(s):  
Andrew Chalmers ◽  
Snjezana Soltic
Keyword(s):  
Light Source ◽  
Large Scale ◽  
Source Spectrum ◽  
Light Sources ◽  
Luminous Efficacy ◽  
Light Emitting ◽  
Spectral Bands ◽  
Good Energy ◽  
Lighting Systems ◽  
Colour Rendering

This paper is concerned with designing light source spectra for optimum luminous efficacy and colour rendering. We demonstrate that it is possible to design light sources that can provide both good colour rendering and high luminous efficacy by combining the outputs of a number of narrowband spectral constituents. Also, the achievable results depend on the numbers and wavelengths of the different spectral bands utilized in the mixture. Practical realization of these concepts has been demonstrated in this pilot study which combines a number of simulations with tests using real LEDs (light emitting diodes). Such sources are capable of providing highly efficient lighting systems with good energy conservation potential. Further research is underway to investigate the practicalities of our proposals in relation to large-scale light source production.

Hybrid-Light-Source Stereolithography for Fabricating Macro-Objects With Micro-Textures

2021 ◽  
Author(s):  
Wenxuan Jia ◽  
Yuen-Shan Leung ◽  
Huachao Mao ◽  
Han Xu ◽  
Chi Zhou ◽  
...  
Keyword(s):  
Light Source ◽  
Dimensional Accuracy ◽  
Beam Width ◽  
Surface Structures ◽  
Light Sources ◽  
Scanning Method ◽  
Hardware System ◽  
Building Area ◽  
Micro Features ◽  
Display Resolution

Abstract Microscale surface structures are commonly found on macroscale bodies of natural creatures for their unique functions. However, it is difficult to fabricate such multi-scale geometry with conventional stereolithography processes that rely on either laser or digital micromirror device (DMD). More specifically, the DMD-based mask projection method displays the image of a cross-section of the part on the resin to fabricate the entire layer efficiently; however, its display resolution is limited by the building area. In comparison, the laser-based vector scanning method builds smooth features using a focused laser beam with desired beam-width resolution; however, it has less throughput for its sequential nature. In this paper, we studied the hybrid-light-source stereolithography process that integrates both optical light sources to facilitate the fabrication of macro-objects with microscale surface structures (called micro-textures in the paper). The hardware system uses a novel calibration approach that ensures pixel-level dimensional accuracy across the two light sources. The software system enables designing the distribution and density of specific microscale textures on a macro-object by generating projection images and laser toolpaths for the two integrated light sources. Several test cases were fabricated to demonstrate the capability of the developed process. A large fabrication area (76.8 mm × 80.0 mm) with 50 μm micro-features can be achieved with a high throughput.

scholarly journals Photobiocatalytic alcohol oxidation using LED light sources

2017 ◽  
Vol 19 (2) ◽  
pp. 376-379 ◽  
Author(s):  
M. Rauch ◽  
S. Schmidt ◽  
I. W. C. E. Arends ◽  
K. Oppelt ◽  
S. Kara ◽  
...  
Keyword(s):  
Light Source ◽  
Photocatalytic Oxidation ◽  
Alcohol Oxidation ◽  
Light Sources ◽  
Blue Led ◽  
Led Light

The photocatalytic oxidation of NADH using a flavin photocatalyst and a simple blue LED light source is reported.

scholarly journals Effect of Supplementary Light Source on Quality of Grafted Tomato Seedlings and Expression of Two Photosynthetic Genes

Agronomy ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 207 ◽  
Author(s):  
Hao Wei ◽  
Jiangtao Hu ◽  
Chen Liu ◽  
Mengzhao Wang ◽  
Jin Zhao ◽  
...  
Keyword(s):  
Light Source ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light Sources ◽  
Seedling Production ◽  
White Leds ◽  
Tomato Seedlings ◽  
Photosynthetic Genes ◽  
Supplementary Lighting

Supplementary lighting is commonly used in high-quality seedling production. In this study, grafted tomato seedlings were grown for 10 days in a glasshouse with 16-h daily supplementary lighting at 100 μmol·m−2·s−1 PPFD (Photosynthetic photon flux density) from either high-pressure sodium (HPS), metal halide (MH), far-red (FR), white LEDs (Light emitting diodes) (W), or mixed LEDs (W1R2B1, where the subscript numbers indicate the ratio of the LED chips) to determine which light sources improve the seedling quality. The control seedlings did not receive any supplementary light. Physiological parameters and the expression of genes related to photosynthesis were analyzed. The results showed that root length, biomass, number of leaves, chlorophyll (SPAD), scion dry weight to height ratio (WHR), and specific leaf weight (SLW) were the greatest for grafted seedlings grown in W1R2B1. The level of root ball formation was the greatest for seedlings grown in W1R2B1, followed by those grown in W, HPS, and MH. Seedlings grown in FR did not fare well, as they were very thin and weak. Moreover, the expression of two photosynthetic genes (PsaA and PsbA) was significantly increased by W1R2B1 and W, which suggests that the plastid or nuclear genes might be regulated. The overall results suggest that W1R2B1 was the most suitable light source to enhance the quality of grafted tomato seedlings. The results of this study could be used as a reference for seedling production in glasshouses, and may provide new insights in the research on lights affecting the development of plants.

scholarly journals Elimination of the blinding effect in landscape luminaires

2018 ◽  
Vol 7 (2.13) ◽  
pp. 252
Author(s):  
Albert Ashryatov ◽  
Dinara Churakova
Keyword(s):  
Light Curve ◽  
Light Source ◽  
Light Flux ◽  
Light Distribution ◽  
Light Sources ◽  
Mirror Surface ◽  
Light Emitting ◽  
Lighting Technology ◽  
Initial Task ◽  
Flat Beam

The article presents one of the possible options for implementing the lighting technology "Flat beam" for landscape lighting purposes. One of the possible ways to control the light distribution of a number of light sources based on LEDs with different radiation patterns is considered. As a secondary optics, it is proposed to use a mirror surface that redistributes the light flux of an LED light source. It is indicated that, depending on the initial type of the light-emitting diodes light curve and the features of mounting the mirror surface, the resulting light distribution can vary widely, depending on the initial task that the designer sets for himself.  

Sign in / Sign up

Export Citation Format

Share Document