Influence of Sintering Temperature on Mechanical Properties of Biologically Derived Hydroxyapatite Bodies

2006 ◽  
Vol 309-311 ◽  
pp. 45-48 ◽  
Author(s):  
Faik N. Oktar ◽  
H. Aydin ◽  
Gültekin Göller ◽  
Simeon Agathopoulos ◽  
G. Rocha ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Time Saving ◽  
Natural Sources ◽  
X Ray ◽  
Calcination Method ◽  
Scanning Electron

The properties of sintered hydroxyapatite (HA), obtained from bovine femoral shafts via calcination method, were investigated utilizing scanning electron microscopy (SEM) and X-ray diffraction analysis together with measurements of microhardness, density, and compression strength. The production of HA from natural sources is preferred due to money and time saving reasons. The results indicate the new HA materials as promissing in biomedicine, since similar mechanical behaviour was obtained with previous studies.

Sintering of Ti3SiC2 Ceramics by Hot Press from Commercial Powders

2015 ◽  
Vol 655 ◽  
pp. 68-71
Author(s):  
Yuan Yuan Zhu ◽  
Jin Jia ◽  
Ai Guo Zhou ◽  
Li Bo Wang ◽  
Qing Feng Zan
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Sintering Temperature ◽  
Hot Press ◽  
X Ray Diffraction ◽  
X Ray ◽  
Three Point Bending ◽  
Ternary Compounds ◽  
Scanning Electron

Layered ternary compounds Ti3SiC2combines attractive properties of both ceramics and metals, and has been suggested for potential engineering applications. Near-fully dense Ti3SiC2bulks were sintered from commercial Ti3SiC2powders by hot press at 1350°C-1600°C for 60-120min under Ar atmosphere in this paper. The phase compositions and morphology of the as-prepared samples were evaluated by X-Ray diffraction (XRD) and scanning electron microscopy (SEM). And the mechanical properties were measured by Three-Point bending method. It was found that the Ti3SiC2had only a little of decomposition at sintering temperature above 1350°C. And effects of sintering temperature and holding time on the morphology of the bulk Ti3SiC2are not obvious. Relative density of 98% and flexural strength of 480MPa were obtained for the Ti3SiC2samples sintered at 30MPa and 1400°C for 90min.

Improvement of Microstructure of Bovine Hydroxyapatite with Yttria

2007 ◽  
Vol 330-332 ◽  
pp. 47-50
Author(s):  
L.S. Ozyegin ◽  
S. Salman ◽  
Faik N. Oktar ◽  
Simeon Agathopoulos ◽  
Onur Meydanoglu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Bovine Bone ◽  
X Ray Diffraction ◽  
Time Saving ◽  
Natural Sources ◽  
X Ray ◽  
Study Results ◽  
Bovine Hydroxyapatite ◽  
Scanning Electron

Composites of calcinated bovine bone derived hydroxyapatite (HA) with 0.5 and 1 wt% Y2O3 were prepared by sintering. Money and time saving feature the production of HA from natural sources. In this study, results of scanning electron microscopy (SEM) and X-ray diffraction analysis aimed to interpret the results of measurements of densification, microhardness, and compression strength of the produced composites. The best mechanical properties were achieved after sintering at 1200°C for compressive strength and 1300°C for microhardness. The results are in a fair agreement with densification measurements and microstructure analysis.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

scholarly journals Structure and Morphology Properties of Nanoparticle Hematite Pigment from Lathe Waste

2021 ◽  
Vol 13 (1) ◽  
pp. 21
Author(s):  
Lilik Miftahul Khoiroh ◽  
Asmaul Dwi Ayu Sholekah ◽  
Eny Yulianti
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Diffraction Data ◽  
X Ray Diffraction ◽  
Crystallinity Degree ◽  
X Ray ◽  
Structure And Morphology ◽  
Calcination Method ◽  
Scanning Electron ◽  
Color Reader

Hematite coated PEG was synthesized by the sonication-calcination method. A variation of Na2CO3 is investigated to know the effect on structure and morphology. Characterization of samples are using X-ray fluorescence, X-ray diffraction, Scanning electron microscopy, and color reader techniques. XRF data showed that iron is the highest element in the precursor. The X-ray diffraction data confirm that Fe(OH)3, α-FeOOH, and Fe3O4 established at the sonication stage are then transformed into the α-Fe2O3 phase after calcination. The X-ray diffraction data also was found that α-Fe2O3 at 0.5 M formed with the highest crystallinity degree. The scanning electron microscopy showed that the particle's shape is spherical, bar-shaped, and aggregate. However, the distribution of particles is not uniform and still displays agglomeration. The Color reader shows the highest degree of lightness obtained is at 1 M variation.

scholarly journals Pengaruh Suhu Sintering Terhadap Sintesis Silicon Carbide (SiC) Berbahan Dasar Abu Sekam Padi dan Grafit Pensil 2B

2015 ◽  
Vol 5 (01) ◽  
pp. 31
Author(s):  
Resky Irfanita ◽  
Asnaeni Ansar ◽  
Ayu Hardianti Pratiwi ◽  
Jasruddin J ◽  
Subaer S
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Rice Husk Ash ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Scanning Electron

The objective of this study is to investigate the effect of sintering temperature on the synthesis of SiC produced from rice husk ash (RHA) and 2B graphite pencils. The SiC was synthesized by using solid state reaction method sintered at temperatures of 750°C, 1000°C and 1200°C for 26 hours, 11.5 hours and 11.5 hours, respectively. The quantity and crystallinity level of SiC phase were measured by means of Rigaku MiniFlexII X-Ray Diffraction (XRD). The microstructure of SiC was examined by using Tescan Vega3SB Scanning Electron Microscopy (SEM). The XRD results showed that the concentration (wt%) of SiC phase increases with the increasing of sintering temperature. SEM results showed that the crystallinity level of SiC crystal is improving as the sintering temperature increases

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

2017 ◽  
Vol 12 (1) ◽  
pp. 63-77 ◽  
Author(s):  
Siriporn Sirikingkaew ◽  
Nuta Supakata
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Phase Composition ◽  
Fly Ash ◽  
Industrial Waste ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

This study presents the development of geopolymer bricks synthetized from industrial waste, including fly ash mixed with concrete residue containing aluminosilicate compound. The above two ingredients are mixed according to five ratios: 100:0, 95:5, 90:10, 85:15, and 80:20. The mixture's physico-mechanical properties, in terms of water absorption and the compressive strength of the geopolymer bricks, are investigated according to the TIS 168-2546 standard. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens. The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production, as required by the TIS 168–2546 standard.

scholarly journals Amazonian Metakaolin Reactivity for Geopolymer Synthesis

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Ruy A. Sá Ribeiro ◽  
Marilene G. Sá Ribeiro ◽  
Gregory P. Kutyla ◽  
Waltraud M. Kriven
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
Local Resource ◽  
X Ray ◽  
Potassium Sodium ◽  
Mixing Intensity ◽  
Amazonian Region ◽  
Scanning Electron

To determine the viability of using a local resource for geopolymer synthesis, geopolymers were synthesized using metakaolin made from clay mined in the Amazonian region of Brazil. Samples were made with mixed potassium-sodium and pure sodium metakaolin-based geopolymer. Samples were also made using commercial metakaolin (CMK) from BASF, Inc. as a comparison to the Amazonian metakaolin (AMK). Scanning electron microscopy was used to investigate the microstructure of the materials. X-ray diffraction was able to confirm the formation of geopolymer. The mechanical properties of AMK material were nearly equivalent to those based on CMK. Neither CMK nor AMK reacted completely, although samples made with CMK showed less unreacted material. By increasing the mixing intensity and duration, the amount of residual unreacted material was substantially reduced, and mechanical properties were improved.

Preparation and Properties of CaF2 Nano-Powder

2016 ◽  
Vol 680 ◽  
pp. 257-260
Author(s):  
Meng Yun Dong ◽  
Cheng Zhang ◽  
Jin Feng Xia ◽  
Hong Qiang Nian ◽  
Dan Yu Jiang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Particle Size ◽  
Sintering Temperature ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Powder ◽  
Direct Precipitation ◽  
Scanning Electron

CaF2 nano-power was prepared by direct precipitation methods with Ca(NO3)2 and KF as raw materials. The influences of presintering temperature and sintering temperature on the particle size and distribution of CaF2 nano-power were studied by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM). This study provided an experimental method for preparation of CaF2 nano-power. The results show that the best presintering temperature of CaF2 nano-power is 500°C and the best sintering temperature of CaF2 ceramic is 900°C.

Preparation of Construction Bricks from Iron Ore Tailings

2012 ◽  
Vol 557-559 ◽  
pp. 839-844 ◽  
Author(s):  
Gao Xiang Du ◽  
Ran Fang Zuo ◽  
Wei Juan Guo ◽  
Jing Hui Liao
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Bulk Density ◽  
Iron Ore ◽  
Sintering Temperature ◽  
Loss On Ignition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Iron Ore Tailings ◽  
Scanning Electron

Based on the background that large amount of iron ore tailings are stockpiled in China, the utilization of iron ore tailings to prepare sintering brick was studied. The main objective of this paper was to investigate the influence of sintering temperature on sintering bricks from iron ore tailings, in the presence of clay, coal refuses and bentonite. Sintering bricks were prepared at different temperature with 40 wt% iron ore tailings. Drying was investigated as well as the loss on ignition, bulk density and compressive strength of the specimens. Their mechanical and microstructure properties were also investigated by radioactivity, scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that compressive strengths of the specimens produced were higher than that required by the standards MU20 of GB5101-2003, up to 128.0Mpa at 1100°C corresponding to its higher bulk density completely.

Sign in / Sign up

Export Citation Format

Share Document