The Influence of Microstructure and Chemical Composition on the Strength of Cast Iron Used for Railway Vehicles

2006 ◽  
Vol 321-323 ◽  
pp. 1479-1482
Author(s):  
Young Min Lee ◽  
Yong Huh ◽  
Jae Sil Park ◽  
Chang Sung Seok
Keyword(s):  
Tensile Strength ◽  
Cast Iron ◽  
Chemical Composition ◽  
Tensile Tests ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
Brake Disk ◽  
Disk Material ◽  
The Difference ◽  
Si Content

Generally, the shape of graphite and the contents of elements strongly affect the tensile strength of cast iron. In this study, hardness tests and tensile tests for the two types of gray cast iron were carried out. The test results showed the similarity in the hardness but considerable difference in the tensile strength between two materials. Microstructure analysis and chemical analysis were conducted to determine the cause for the difference in the tensile strength between the two types of cast iron. The experimental results showed differences in the microstructure and chemical composition between the two materials. B-type brake disk material(B-type) that had higher tensile strength includes flake, vermicular and spheroidal graphite, whereas A-type brake disk material (A-type) included only flake graphite in the structure. Nodularity of graphite in the B-type was higher than that in the A-type. Also, the B-type had the higher Si content and lower Mn content. In addition, the B-type had Cu, while the A-type did not. Therefore, we concluded that the difference in the strength between the two types of cast iron was due to the difference in the shape of the graphite and the contents of Cu in the cast irons.

ISO 185/JL/350

Alloy Digest ◽  
2021 ◽  
Vol 70 (9) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Cast Iron ◽  
Gray Cast Iron ◽  
High Strength ◽  
Heat Treating ◽  
Gray Cast ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
Test Pieces

Abstract ISO 185/JL/350 is a higher-tensile-strength gray cast iron that has a pearlitic matrix, and a tensile strength of 350–450 MPa (51–65 ksi), when determined on test pieces machined from separately cast, 30 mm (1.2 in.) diameter test bars. It provides a combination of high strength while still maintaining good thermal conductivity compared with other types of cast iron. This grade approaches the maximum tensile strength attainable in gray cast iron. Applications therefore tend to be confined to those where thermal conductivity requirements in service preclude the use of one of the other higher-strength materials such as spheroidal graphite cast irons, which have inferior thermal properties. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on wear resistance as well as casting and heat treating. Filing Code: CI-85. Producer or source: International Organization for Standardization.

scholarly journals Ausferritic (bainitic) cast iron: Harmonization of international standard ISO 17804 in application to the conditions of Belarus

2021 ◽  
pp. 56-72
Author(s):  
A. I. Pokrovskii ◽  
B. B. Khina ◽  
O. A. Tolkacheva
Keyword(s):  
Tensile Strength ◽  
Cast Iron ◽  
Ductile Iron ◽  
High Strength ◽  
State Committee ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
International Standard ◽  
Industrial Enterprises ◽  
State Organizations

The experience of the Physico-technical Institute (PhTI) of the National Acdemy of Sciences of Belarus in the harmonization of international standard ISO 17804 (Founding – Ausferritic spheroidal graphite cast irons – Classification) and development of the Belorussian analogue STB ISO is described. The reasons for the choice of austempered ductile iron (ADI) as an object for standard harmonization are presented: it is the most promising cast iron in comparison with gray and classical ductile iron. The work procedure on harmonization is described: how to include the task into the State Plan on standardization, specificity of translation of the text, peculiarities of with state organizations responsible for approbation of standards such as Belorussian Institute for Standardization and Certification (BelGISS) and State Committee on Standards (Gosstandart), writing a summary of external reviews, working with critical comments from potential users. It is outlined that any foreign standard does not exists independently but is closely connected with at least 10 to 20 other standards. Thus, harmonization necessitates coordination with other standards and sometimes even with handbooks by adding annexes to the main text. The importance of a proper choice of the standard status is outlined: identical (ID) or modified (MOD). Developing an identical standard is prestigious but difficult because is requires harmonization of all the referenced standards, which is a very labor-consuming procedure. It is argued that the most suitable is ‘intermediate’ variant: adopting the authentic text of the international standard (in high-quality translation) but with annexes reflecting national specificity in this area. As a result, a harmonized standard is developed which, for the first time in Belarus, standardize the tensile strength of 800 MPa in combination with the elongation of 10 % and the tensile strength of 1400 MPa in combination with the elongation of 1 % for cast irons.The annual demand for ADI in Belarus is estimated as about 10,000 ton. It is shown that in Belarus, where about 60 industrial enterprises have a foundry and almost every engineering plant has a heat-treatment shop, austempered ductile cast (ADI), which features a high strength, can successfully compete with rolled steel in certain applications.

ISO 185/JL/300

Alloy Digest ◽  
2021 ◽  
Vol 70 (6) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Cast Iron ◽  
Gray Cast Iron ◽  
High Strength ◽  
Heat Treating ◽  
Gray Cast ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
Test Pieces

Abstract ISO 185/JL/300 is a higher-tensile-strength gray cast iron that has a pearlitic matrix; it has a tensile strength of 300–400 MPa (44–58 ksi), when determined on test pieces machined from separately cast, 30 mm (1.2 in.) diameter test bars. It provides high strength while still maintaining good thermal conductivity compared with other types of cast iron. This grade approaches the maximum tensile strength attainable in gray cast iron. Applications therefore tend to be confined to those where thermal conductivity requirements in service preclude the use of one of the other higher-strength materials such as spheroidal graphite cast irons, which have inferior thermal properties. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on casting and heat treating. Filing Code: CI-82. Producer or source: International Organization for Standardization.

MEEHANITE GB300

Alloy Digest ◽  
2020 ◽  
Vol 69 (11) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Gray Cast Iron ◽  
High Strength ◽  
Heat Treating ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
Test Pieces ◽  
Temperature Performance

Abstract Meehanite GB300 is a pearlitic gray cast iron that has a minimum tensile strength of 300 MPa (44 ksi), when determined on test pieces machined from separately cast, 30 mm (1.2 in.) diameter test bars. This grade exhibits high strength while still maintaining good thermal conductivity and good machinability. It is generally used for applications where the thermal conductivity requirements preclude the use of other higher-strength materials, such as spheroidal graphite cast irons, which have inferior thermal properties. This datasheet provides information on physical properties, hardness, tensile properties, and compressive strength as well as fatigue. It also includes information on low and high temperature performance as well as heat treating, machining, and joining. Filing Code: CI-75. Producer or source: Meehanite Metal Corporation.

scholarly journals Solidification Pattern of Si-Alloyed, Inoculated Ductile Cast Irons, Evaluated by Thermal Analysis

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 846
Author(s):  
Iuliana Stan ◽  
Denisa Anca ◽  
Stelian Stan ◽  
Iulian Riposan
Keyword(s):  
Cast Iron ◽  
Eutectic Reaction ◽  
Influencing Factor ◽  
Cooling Curve ◽  
Major Influence ◽  
Cast Irons ◽  
Minor Elements ◽  
Si Content ◽  
Si Effect ◽  
Positive Effect

The solidification cooling curve itself as well as its first derivative, and related temperatures, reported to the calculated equilibrium temperatures in stable and metastable solidification systems, are used to predict the solidification characteristics of the cast iron. Silicon, as the most representative cast iron element, and inoculation, as graphitizing metallurgical treatment, have a major influence on the transition from the liquid to the solid state. Six experimental programs are performed, with Si content typically for non-alloyed (<3.0% Si), low (3.0–3.5% Si) and medium alloyed (4.5–5.5% Si) ductile cast irons, as Si-content increasing, and inoculation simultaneous effects. Silicon is an important influencing factor, but the base and minor elements also affect the equilibrium eutectic temperatures, much more in the Fe-C-Si-Xi stable system (15–20 °C) than in the metastable system (5–10 °C), comparing with their calculation based only on a Si effect (Fe-C-Si system). The highest positive effect of inoculation is visible in non-Si alloyed cast irons (2.5% Si): 9–15 °C for the eutectic reaction and 3 to 4 times increased at the end of solidification (37–47 °C). Increased Si content decreases inoculation power to 7–9 °C for low alloying grade (up to 3.5% Si), with the lowest contribution at more than 4.5% Si (0.3–2.0 °C). 2.5–3.5% Si ductile cast irons are more sensitive to high solidification undercooling, especially at the end of solidification (but with a higher efficiency of inoculation), compared to 4.5–5.5% Si ductile cast irons, at a lower undercooling level, and at lower inoculation contribution, as well.

Semisolid Forging of Cast Iron Using Rapid Resistance Heating

2007 ◽  
Vol 561-565 ◽  
pp. 925-928 ◽  
Author(s):  
Seijiro Maki ◽  
Kazuhito Suzuki ◽  
Kenichiro Mori
Keyword(s):  
Cast Iron ◽  
Control Function ◽  
Electric Energy ◽  
Spheroidal Graphite ◽  
Pig Iron ◽  
Resistance Heating ◽  
Cast Irons ◽  
Ac Power ◽  
Spheroidal Graphite Cast Iron ◽  
Graphite Cast Iron

Feasibility of semisolid forging of cast iron using rapid resistance heating was experimentally investigated. Gray pig iron FC250 and spheroidal graphite cast iron FCD600, whose carbon equivalents are both 4.3% in mass, were used for the experiments. Since these cast irons have a narrow semisolid temperature range, an AC power supply with an input electric energy control function was used. In this study, the resistance heating characteristics of the cast irons were firstly examined, and then their semisolid forging experiments were conducted. In the forging experiments, the conditions of the forgings such as microstructures and hardness properties were examined, and the feasibility of the semisolid forging of cast iron using resistance heating was discussed. As a result, it was found that the method presented here is highly feasible.

Influence of Ca-Ba and Sr Base Inoculants on Metallurgical and Mechanical Properties of Grey and Ductile Cast Irons

2018 ◽  
Author(s):  
Dhruv Patel ◽  
Devendra Parmar ◽  
Siddharthsinh Jadeja
Keyword(s):  
Mechanical Properties ◽  
Cast Iron ◽  
Uniform Distribution ◽  
Ductile Cast Iron ◽  
Grain Structure ◽  
Spheroidal Graphite ◽  
Primary Carbide ◽  
Cast Irons ◽  
Melt Temperature ◽  
Nodular Graphite

Microstructural adaptation of cast iron alloys by inoculation is a well-known practice to swell their mechanical properties. In foundries, several inoculants have been used to refine grain structure, and to obtain uniform distribution of graphite flakes. Inoculation is one of the most critical steps in cast iron production. The effectiveness of inoculants depends on melt temperature, method of addition, type of inoculants, and holding time. In this paper, the effect of Ca-based, Ba-based, Ca-Ba based and Sr-based inoculants on microstructure and tensile properties of grey cast iron IS-210 and spheroidal graphite iron IS-1862 is reported. Results showed both Ca and Ba based inoculants were effective in obtaining uniform distribution of flaky and nodular graphite in IS-210, and IS-1862 cast irons, respectively. But in a case of Sr-based inoculant were highly effective for increase the nodularity of SG cast iron as well as succeed supreme yield strength for both grey and ductile cast iron. The amounts of ferrite in the as-cast matrix are excess with controlled granulometry for elimination of primary carbide in Sr-based inoculant.

Effects of Nickel substitution by Manganese in Austenitic S.G. Cast Iron for Low-Temperature Uses

1984 ◽  
Vol 34 ◽  
Author(s):  
P. Poyet ◽  
P. Couchinave ◽  
P. I. Dancoisne
Keyword(s):  
Cast Iron ◽  
Low Temperature ◽  
Tensile Properties ◽  
Room Temperature ◽  
Manganese Content ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
Cast Material ◽  
Mechanical Tensile ◽  
High Level

ABSTRACTFor an economical purpose, an austenitic spheroidal graphite cast iron grade, containinq nickel-manganese, has been developed to replace Ni-Resist cast iron, type D2M, for cryogenic applications.Several tests were carried out to produce semi-industrial. heats of 200 kg so as to cast samples with a thickness ranging between 25 and 75 mm, and a variable nickel and manganese content. The resulting grades were compared each other and with Ni-Resist cast irons, before and after heat treatment, for their metallographic structure, their hardness, their mechanical tensile properties at room temperature and their impact values at temperatures down to - 150° C.The results show that it is possible to produce cast iron grades with 7 to 10 % manganese and 9 to 11 % nickel contents, featuring, at quenched state, better mechanical tensile properties at room temperature than Ni- Resist D2M with a 22–25 % Ni content, for roughly equivalent impact values at low temperatures. For as-cast material, the properties obtained vary with material thickness, and ductility is steeply decreasing for thicknesses under 30 mm.Weldability of Ni/Mn cast iron can be compared to Ni-Resist D2M weldability; machinability however seems more difficult, especially when boring quenched material.Generally speaking, the overall properties of these new grades and their lower cost-price if compared to Ni-Resist cast iron, should lead to promising outlets for low temperature uses and/or applications requiring high-level mechanical properties.

The Relationship between Tensile Strength and Microstructure in Flake Graphite Cast Iron

1984 ◽  
Vol 34 ◽  
Author(s):  
R. N. Castillo ◽  
T. J. Baker
Keyword(s):  
Fracture Toughness ◽  
Tensile Strength ◽  
Cast Iron ◽  
Cell Size ◽  
Eutectic Cell ◽  
Flake Graphite ◽  
Cast Irons ◽  
Graphite Cast Iron ◽  
Flake Graphite Cast Iron ◽  
The Relationship

ABSTRACTThe effects of composition and process variables on the tensile strength of flake graphite cast iron are well established. However, when compared with most metallic materials, there is little quantitative understanding of the way in which the microstructure controls the mechanical properties. In this paper a fracture mechanics approach is used to develop a mechanistic interpretation of the relationship between the microstructure and tensile strength. Flake graphite cast irons have been studied in which matrix microstructures of pearlite, ferrite and tempered martensite have been developed by heat treatment. For a given eutectic cell size, a linear relationship exists between the tensile strength and the fracture toughness KIC, for all of the matrix structures studied. The tensile strength is interpreted as a brittle fracture stress which is determined by the fracture toughness of the iron and an inherent defect size which is defined by the eutectic cell size.

Sign in / Sign up

Export Citation Format

Share Document