Development of a Rubber-Bonded Grinding Wheel - Studies on Aspherical Grinding -

2007 ◽  
Vol 329 ◽  
pp. 465-470 ◽  
Author(s):  
Nobuhito Yoshihara ◽  
Ji Wang Yan ◽  
Tsunemoto Kuriyagawa
Keyword(s):  
Surface Roughness ◽  
Grinding Wheel ◽  
Optical Instrument ◽  
Form Accuracy ◽  
Optical Instruments

Aspherical surfaces are an important technology in optical instruments. Until now, only improvements in form accuracy and surface roughness of aspherical surfaces have been investigated. However, when the surface roughness becomes low, the small waviness of the surface becomes marked. This small waviness is termed “Nano-topography.” Nano-topography causes grinding marks and reduces the accuracy of an optical instrument. Nano-topography is caused by the vibration of a grinding wheel during the manufacture of the surface. This paper will reveal how a rubber-bonded grinding wheel has been developed to absorb that vibration. The dressing of the grinding wheel was also investigated. As a result, it is possible to eliminate the generation of nano-topography.

Nano-Precision Synergistic Finishing Process Integrated ELID-Grinding and MRF

2009 ◽  
Vol 69-70 ◽  
pp. 49-53
Author(s):  
Shao Hui Yin ◽  
Hitoshi Ohmori ◽  
Wei Min Lin ◽  
Yoshihiro Uehara ◽  
Feng Jun Chen ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Optical Materials ◽  
High Efficiency ◽  
High Surface ◽  
Grinding Wheel ◽  
Form Accuracy ◽  
High Surface Quality ◽  
Elid Grinding ◽  
Finishing Process ◽  
Magneto Rheological

ELID (electrolytic in-process dressing) grinding was proposed by one of the authors for automatic dressing the grinding wheel while performing grinding for a long time. It offers a high effective way and has been widely used for grinding hard and brittle optical materials. However, those surfaces produced by fixed abrasive grinding are characterized by considerable sub-surface damage, micro-crack. Magneto-rheological finishing (MRF) is a novel precision finishing process for deterministic form correction and polishing of optical materials by utilizing magneto-rheological fluid. In this paper, an ultra-precision synergistic finishing process integrated MRF and ELID grinding is proposed for shorten total finishing time and improve finishing quality. A lot of nano-precision experiments have been carried out to grind and finish some optical materials such as silicon, silicon carbide, etc. ELID grinding is employed to obtain high efficiency and high surface quality, and then, MRF is employed to improve further surface roughness and form accuracy. In general, form accuracy of ~ λ/20 nm peak-to-valley (P-V) and surface roughness less than 10 Angstrom are produced in high efficiency.

Nano-Topography Distribution on Non-Axisymmetric Aspherical Ground Surface

2011 ◽  
Vol 325 ◽  
pp. 66-71 ◽  
Author(s):  
Nobuhito Yoshihara ◽  
Shin Fujimura ◽  
Naohiro Nishikawa ◽  
Masahiro Mizuno ◽  
Toshirou Iyama
Keyword(s):  
Surface Roughness ◽  
Smooth Surface ◽  
Ground Surface ◽  
Simulation Method ◽  
Grinding Wheel ◽  
Precision Grinding ◽  
Form Accuracy

Both form accuracy and smooth surface is required in precision grinding. And the form accuracy and surface roughness are improved year by year. However, the more the surface roughness becomes smoother, the more the grinding marks become remarkable. The grinding mark deteriorates the accuracy of optical parts. It is found that the vibration of grinding wheel is transcribed to the ground surface and forms the waviness named nano-topography. And the nano-topography causes grinding marks. In this study, relationship between the nano-topography on non-axisymmetric aspherical ground surface and grinding condition is analyzed theoretically to control the distribution of nano-topography. As a result, simulation method of nano-topography distribution is developed.

New Compensation Grinding of Axisymmetric Aspherical Lenses with High NA Value

2005 ◽  
Vol 291-292 ◽  
pp. 51-56
Author(s):  
Nobuhito Yoshihara ◽  
Tsunemoto Kuriyagawa
Keyword(s):  
Grinding Wheel ◽  
Grinding Process ◽  
Form Error ◽  
Cross Sectional ◽  
Form Accuracy ◽  
Optical Instruments ◽  
Grinding Method ◽  
Cross Sectional Profile ◽  
Aspherical Lenses ◽  
Sectional Profile

Aspherical parts are installed in various optical instruments. At present, a higher form accuracy is required for aspherical parts to improve the resolution of the optical instruments. To meet this demand, an arc envelope grinding method has been developed. In the arc envelope grinding process, a spherical shaped grinding wheel is used and the form error of the cross-sectional profile of the grinding wheel is transcribed to the workpiece profile. Therefore, the grinding wheel should be trued previously. However, the form error of the grinding wheel cannot be removed perfectly. To reduce the affect of the form error of the grinding wheel, compensation grinding must be carried out. In this work, the wheel path of a new compensation grinding method is proposed for a high NA value of the workpiece. Tests using the new compensation grinding method demonstrate the reduction in the form error of aspherical parts.

scholarly journals Study on the Effect of Grinding Pressure on Material Removal Behavior Performed on a Self-Designed Passive Grinding Simulator

2021 ◽  
Vol 11 (9) ◽  
pp. 4128
Author(s):  
Peng-Zhan Liu ◽  
Wen-Jun Zou ◽  
Jin Peng ◽  
Xu-Dong Song ◽  
Fu-Ren Xiao
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Service Life ◽  
Material Removal ◽  
Removal Rate ◽  
Grinding Force ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Temperature ◽  
Grinding Efficiency

Passive grinding is a new rail grinding strategy. In this work, the influence of grinding pressure on the removal behaviors of rail material in passive grinding was investigated by using a self-designed passive grinding simulator. Meanwhile, the surface morphology of the rail and grinding wheel were observed, and the grinding force and temperature were measured during the experiment. Results show that the increase of grinding pressure leads to the rise of rail removal rate, i.e., grinding efficiency, surface roughness, residual stress, grinding force and grinding temperature. Inversely, the enhancement of grinding pressure and grinding force will reduce the grinding ratio, which indicates that service life of grinding wheel decreases. The debris presents dissimilar morphology under different grinding pressure, which reflects the distinction in grinding process. Therefore, for rail passive grinding, the appropriate grinding pressure should be selected to balance the grinding quality and the use of grinding wheel.

Surface integrity of quenched steel 1045 machined by CBN grinding wheel and SiC grinding wheel

2017 ◽  
Vol 8 (2) ◽  
pp. 179-187 ◽  
Author(s):  
Kankan Ji ◽  
Xingquan Zhang ◽  
Shubao Yang ◽  
Liping Shi ◽  
Shiyi Wang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Morphology ◽  
Compressive Stress ◽  
Surface Integrity ◽  
Grinding Wheel ◽  
Micro Hardness ◽  
Content Type ◽  
Quenched Steel ◽  
Cut Depth ◽  
Cbn Grinding Wheel

Purpose The purpose of this paper is to evaluate surface integrity of quenched steel 1045 ground drily by the brazed cubic boron nitride (CBN) grinding wheel and the black SiC wheel, respectively. Surface integrity, including surface roughness, sub-surface hardness, residual stresses and surface morphology, was investigated in detail, and the surface quality of samples ground by two grinding wheels was compared. Design/methodology/approach In the present work, surface integrity of quenched steel 1045 machined by the CBN grinding wheel and the SiC wheel was investigated systematically. All the specimens were machined with a single pass in the down-cutting mode of dry condition. Surface morphology of the ground specimen was observed by using OLYMPUS BX51M optical microscopy. Surface roughness of seven points was measured by using a surface roughness tester at a cut-off length of 1.8 mm and the measurement traces were perpendicular to the grinding direction. Sub-surface micro-hardness was measured by using HVS-1000 digital micro-hardness tester after the cross-section surface was polished. The residual stress was tested by using X-350A X-ray stress analyzer. Findings When the cut depth is increased from 0.01 to 0.07 mm, the steel surface machined by the CBN wheel remains clear grinding mark, lower roughness, higher micro-hardness and higher magnitude of compressive stress and fine microstructure, while the surface machined by the SiC grinding wheel becomes worse with increasing of cut depth. The value of micro-hardness decreases, and the surface roughness increases, and the surface compressive stress turns into tensile stress. Some micro-cracks and voids occur when the sample is processed by the SiC grinding wheel with cut depth 0.07 mm. Originality/value In this paper, the specimens of quenched steel 1045 were machined by the CBN grinding wheel and the SiC wheel with various cutting depths. The processing quality resulted from the CBN grinding wheel is better than that resulted from the SiC grinding wheel.

scholarly journals Performance of Norton Quantum Grinding Wheels

2016 ◽  
Vol 686 ◽  
pp. 125-130 ◽  
Author(s):  
Miroslav Neslušan ◽  
Jitka Baďurová ◽  
Anna Mičietová ◽  
Maria Čiliková
Keyword(s):  
Surface Roughness ◽  
Ground Surface ◽  
Bearing Steel ◽  
Grinding Wheel ◽  
Grinding Wheels ◽  
Grinding Forces ◽  
Removal Rates ◽  
Surface Burn ◽  
Conventional Grinding

This paper deals with cutting ability of progressive Norton Quantum grinding wheel during grinding roll bearing steel 100Cr6 of hardness 61 HRC. Cutting ability of this wheel is compared with conventional grinding wheel and based on measurement of grinding forces as well as surface roughness. Results of experiments show that Norton Quantum grinding wheels are capable of long term grinding cycles at high removal rates without unacceptable occurrence of grinding chatter and surface burn whereas application of conventional wheel can produce excessive vibration and remarkable temper colouring of ground surface. Moreover, while Norton Quantum grinding wheel gives nearly constant grinding forces and surface roughness within ground length at higher removal rates, conventional grinding wheel (as that reported in this study) does not.

Development of a New Plate Polishing Technique with an Instantaneous Tiny-Grinding Wheel Cluster Based on Magnetorheological Effect

2008 ◽  
Vol 53-54 ◽  
pp. 155-160 ◽  
Author(s):  
Qiu Sheng Yan ◽  
Ai Jun Tang ◽  
Jia Bin Lu ◽  
Wei Qiang Gao
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Grinding Wheel ◽  
Abrasive Particles ◽  
Magnetorheological Effect ◽  
Material Removal Model ◽  
Mr Effect ◽  
Removal Model

A new plate polishing technique with an instantaneous tiny-grinding wheel cluster based on the magnetorheological (MR) effect is presented in this paper, and some experiments were conducted to prove its effectiveness and applicability. Under certain experimental condition, the material removal rate was improved by a factor of 20.84% as compared with the conventional polishing methods with dissociative abrasive particles, while the surface roughness of the workpiece was not obviously increased. Furthermore, the composite of the MR fluid was optimized to obtain the best polishing performance. On the basis of the experimental results, the material removal model of the new plate polishing technique was presented.

Development of Electroplated CBN Wheel with Cemented Carbide Base for Precision Grinding of Compressor Cylinder Vane Slot

2007 ◽  
Vol 329 ◽  
pp. 495-500
Author(s):  
Hang Gao ◽  
W.G. Liu ◽  
Y.G. Zheng
Keyword(s):  
Surface Roughness ◽  
Ground Surface ◽  
Cemented Carbide ◽  
Grinding Wheel ◽  
Precision Grinding ◽  
Base Surface ◽  
Compressor Cylinder ◽  
Cbn Wheel ◽  
Micro Holes ◽  
Ground Surface Roughness

It is experimentally found that existing micro-holes or micro-concaves on the cemented carbide base surface of electroplated CBN wheel is one of important reasons to worsen the combining intensity of the electroplated abrasives layer with the grinding wheel base. It is well solved by sealing the holes or concaves with steam sealing method. Further more the electroplated CBN wheel with cemented carbide base for precision grinding of compressor cylinder vane slot is developed by optimizing the electroplating prescription and process. Productive grinding results show that the ground surface roughness, size precision and the wheel life have reached the advanced index of the same type of wheel imported.

scholarly journals The influence of the profile-dividing grinding strategy on the surface accuracy and roughness of a gear teeth

Mechanik ◽  
2018 ◽  
Vol 91 (8-9) ◽  
pp. 737-740 ◽  
Author(s):  
Piotr Zyzak ◽  
Paweł Kobiela ◽  
Arnold Brożek ◽  
Marek Gabryś
Keyword(s):  
Surface Roughness ◽  
Grinding Wheel ◽  
Machining Accuracy ◽  
Cylindrical Gear ◽  
Gear Teeth ◽  
Surface Accuracy ◽  
Number Of Passes

In the paper are presented investigation results of an effects of adopted strategy of profile-dividing grinding of a cylindrical gear teeth, performed on the Rapid Höfler 900 grinder, on machining accuracy and surface roughness of the teeth. The strategies have taken into considerations changes in the following parameters determining obtained results of the grinding: number of passes, number of leads, shaping method of the grinding wheel.

scholarly journals Efektifitas Pembelajaran Berbasis Inquiry Melalui Implementasi Modeling Instruction pada Materi Alat Optik

2021 ◽  
Vol 8 (4) ◽  
pp. 545
Author(s):  
Soekarman Soekarman
Keyword(s):  
Inquiry Learning ◽  
Optical Instrument ◽  
Student Responses ◽  
Student Activities ◽  
Inquiry Based Learning ◽  
Modeling Instruction ◽  
Optical Instruments ◽  
Descriptive Research ◽  
Quantitative Descriptive

This study aims to analyze inquiry-based learning through the implementation of modeling instruction on optical instrument materials. This research method used quantitative descriptive research. The subjects of this study were students of class XI IPA SMAN 2 Donggo. The collection technique includes observation, literature review, questionnaire, test and documentation. The data obtained will be analyzed descriptively quantitatively, among the research data to be analyzed are: student activities, learning outcomes, and student responses to ongoing learning. The results of this study include: 1) Student activity obtained a score of 74.58% or good category, 2) Inquiry learning with Modeling Instruction on optical instrument material can actually improve students' understanding with an N-gain score of 1.3 points or very high category. high, 3) Student responses to learning obtained a score of 84.37% or very interesting category. Based on the results of the study, it was found that through Inquiry learning with Modeling Instruction on Optical Instruments material, it can be used as an alternative to improve the quality of learning in class, especially in Physics subjects.

Sign in / Sign up

Export Citation Format

Share Document