About the Effects of Residual Stress States Coming from Manufacturing Processes on the Behaviour of Riveted Joints

2008 ◽  
Vol 385-387 ◽  
pp. 25-28 ◽  
Author(s):  
Francesco Caputo ◽  
Giuseppe Lamanna ◽  
Alessandro Soprano
Keyword(s):  
Residual Stress ◽  
Failure Modes ◽  
Pressure Effects ◽  
Load Pressure ◽  
Aerospace Applications ◽  
Joint Characteristics ◽  
Riveted Joints ◽  
Stress States ◽  
The Many ◽  
Operational Behaviour

A very large number of variables affect the response of bolted or riveted joints typically used in aerospace applications: geometry of the joint, characteristics of the sheets, friction between sheets, geometry of head and kind of fastener, amplitude of clearance before assembly, mounting axial load, pressure effects after manufacture. It must be also recalled that these parameters influence the many failure modes existing for such joints, among which a relevant importance is attributed to bearing. The present paper deals with the study of the influence of assembly parameters on the joint operational behaviour and in particular with the analysis, performed through numerical simulations, of the influence of the residual stress-strain state coming from the riveting operation on the bearing resistance of an aluminium alloy joint. This work has been developed within the FP6 research project called MUSCA (Non linear static multiscale analysis of large aero-structures).

Residual Stress Engineering in Fatigue Resistant Welds

2013 ◽  
Vol 768-769 ◽  
pp. 613-619
Author(s):  
Majid Farajian ◽  
Zuheir Barsoum ◽  
Arne Kromm
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Body Of Knowledge ◽  
Fatigue Design ◽  
Welding Technology ◽  
Stress Engineering ◽  
Solid Foundation ◽  
Stress States ◽  
The Many ◽  
Quantitative Consideration

The developments in the field of residual stress determination during the last decades have contributed to a better understanding of the origins and sources of residual stresses in different engineering disciplines. The many investigations concerning the behavior of residual stresses under mechanical loading have also provided a solid foundation to clarify the important aspects of residual stresses and fatigue. The question that arises now is if this available body of knowledge is being used effectively in the field of welding technology to design and construct structures with better fatigue performances. In this paper the necessity of the development of the concept residual stress engineering for welds in which wanted residual stress states are tailored for specific cases by appropriate means will be discussed. The possibilities of the quantitative consideration of the benefits in the fatigue design codes will be presented in a practical example.

X-Ray Diffraction Measurements of Residual Stress Induced by Surface Compressing Methods

2012 ◽  
Vol 729 ◽  
pp. 199-204 ◽  
Author(s):  
Dávid Cseh ◽  
Valéria Mertinger
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Surface Region ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hardened Alloy ◽  
Compressive Stresses ◽  
Machine Parts ◽  
Stress States ◽  
Operational Behaviour

Residual stresses have a fundamental effect on the operational behaviour and lifetime of industrial products. The fatigue resistance of machine parts can be increased by introducing residual compressive stresses into the surface region. For certain machine parts especially in the vehicle industry the residual stress is strongly demanded by the quality control. For this reason, measuring the stress accurately is becoming increasingly important. The Almen test, which only gives a qualitative result, is widely used in the industry. Shot peening and rolling are methods which are suitable for creating elastic residual stresses. This paper examines the technologies used by Rába Futómű Nyrt. to increase the lifetime by means of residual stress. We performed analysis of the residual stress of samples shot peened the same way but under different heat treatment states. We compared the residual stress values of burnished and hardened shaft joints, and the residual stress states of gear made of hardened alloy, comparing the carbonized ones to ones which were shot peened under small intensity.

scholarly journals Statistical analysis of the reproducibility of residual stress measurements in cold extruded parts

2021 ◽  
Author(s):  
Fabian Jaeger ◽  
Alessandro Franceschi ◽  
Holger Hoche ◽  
Peter Groche ◽  
Matthias Oechsner
Keyword(s):  
Residual Stress ◽  
Statistical Analysis ◽  
Stress Measurement ◽  
Industrial Applications ◽  
Cold Extrusion ◽  
X Ray Diffraction ◽  
Forming Process ◽  
X Ray ◽  
Stress States ◽  
Key Aspects

AbstractCold extruded components are characterized by residual stresses, which originate from the experienced manufacturing process. For industrial applications, reproducibility and homogeneity of the final components are key aspects for an optimized quality control. Although striving to obtain identical deformation and surface conditions, fluctuation in the manufacturing parameters and contact shear conditions during the forming process may lead to variations of the spatial residual stress distribution in the final product. This could lead to a dependency of the residual stress measurement results on the relative axial and circumferential position on the sample. An attempt to examine this problem is made by the employment of design of experiments (DoE) methods. A statistical analysis of the residual stress results generated through X-Ray diffraction is performed. Additionally, the ability of cold extrusion processes to generate uniform stress states is analyzed on specimens of austenitic stainless steel 1.4404 and possible correlations with the pre-deformed condition are statistically examined. Moreover, the influence of the coating, consisting of oxalate and a MoS2 based lubricant, on the X-Ray diffraction measurements of the surface is investigated.

scholarly journals Concept for controlled adjustment of residual stress states in semi-finished products by gradation extrusion

2021 ◽  
Author(s):  
René Selbmann ◽  
Markus Baumann ◽  
Mateus Dobecki ◽  
Markus Bergmann ◽  
Verena Kräusel ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Experimental Tests ◽  
Residual Stress Distribution ◽  
Forming Process ◽  
Compressive Stresses ◽  
Energy Consuming ◽  
Stress States ◽  
Set Up ◽  
Time And Energy

AbstractThe residual stress distribution in extruded components and wires after a conventional forming process is frequently unfavourable for subsequent processes, such as bending operations. High tensile residual stresses typically occur near the surface of the wire and thus limit further processability of the material. Additional heat treatment operations or shot peening are often inserted to influence the residual stress distribution in the material after conventional manufacturing. This is time and energy consuming. The research presented in this paper contains an approach to influence the residual stress distribution by modifying the forming process for wire-like applications. The aim of this process is to lower the resulting tensile stress levels near the surface or even to generate compressive stresses. To achieve these residual compressive stresses, special forming elements are integrated in the dies. These modifications in the forming zone have a significant influence on process properties, such as degree of deformation and deformation direction, but typically have no influence on the diameter of the product geometry. In the present paper, the theoretical approach is described, as well as the model set-up, the FE-simulation and the results of the experimental tests. The characterization of the residual stress states in the specimen was carried out by X-ray diffraction using the sin2Ψ method.

Measurements of Residual Stress in the Layers of Thin Film Micro-Gas Sensors

2000 ◽  
Vol 657 ◽  
Author(s):  
Youngman Kim ◽  
Sung-Ho Choo
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Residual Stress ◽  
Gas Sensor ◽  
Gas Sensors ◽  
Micro Gas Sensor ◽  
Thin Film Layer ◽  
Film Layer ◽  
The Difference ◽  
Stress States

ABSTRACTThe mechanical properties of thin film materials are known to be different from those of bulk materials, which are generally overlooked in practice. The difference in mechanical properties can be misleading in the estimation of residual stress states in micro-gas sensors with multi-layer structures during manufacturing and in service.In this study the residual stress of each film layer in a micro-gas sensor was measured according to the five difference sets of film stacking structure used for the sensor. The Pt thin film layer was found to have the highest tensile residual stress, which may affect the reliability of the micro-gas sensor. For the Pt layer the changes in residual stress were measured as a function of processing variables and thermal cycling.

Sensitivity of Macro- and Micro-Residual Stress States of Steel Surfaces to Thermal Influences Caused by Grinding Burn and Laser Treatments

2013 ◽  
Vol 768-769 ◽  
pp. 412-419
Author(s):  
Bernd Eigenmann ◽  
Antje Zösch ◽  
Martin Seidel
Keyword(s):  
Residual Stress ◽  
Threshold Values ◽  
Materials Properties ◽  
X Ray ◽  
Grinding Burn ◽  
Laser Treatments ◽  
Annealing Effects ◽  
Calibration Samples ◽  
Steel Surfaces ◽  
Stress States

Thermal influences, introduced intentionally or unintentionally do have significant effects on surfaces of steel components. Materials properties are reduced by annealing effects or even re-hardening zones can occur. Grinding, one of the most important technological processes for preci-sion manufacturing of hardened steel components, is an important source of thermal influences to steel surfaces. In pronounced cases, these influences are referred to as grinding burn. They are known as possible reasons for gray stains as well as development of cracks and pittings on heavy-duty gears and on roller bearings. The basic effect of thermal influences on the material is a change of the macro- and micro-residual stress states. Therefore, the knowledge of these residual stress states is of fundamental importance. The paper treats the mechanisms of grinding which can lead to thermal influences. Some characteristic appearances of grinding burn are shown and characterized by X-ray macro- and micro residual stress determinations. It is shown that defined laser treatments can be used to create reproducible thermal influences similar to grinding burn. Their effects are also characterized by X-ray residual stress measurements. The sensitivities of X-ray and metallographical investigations are compared. Defined laser traces are proposed as calibration samples for magnetic and eddy current measurements which allow to determine threshold values for the actual apparatus and measuring problem.

Experimental Assessment of the Dynamic Behavior of Polyolefin Thermoplastic Hot Melt Adhesive

2018 ◽  
Author(s):  
Raffaele Ciardiello ◽  
Andrea Tridello ◽  
Luca Goglio ◽  
Giovanni Belingardi
Keyword(s):  
Failure Modes ◽  
Industrial Applications ◽  
Lap Joints ◽  
Adhesive Joints ◽  
Dynamic Tests ◽  
Cohesive Failure ◽  
Static Tests ◽  
Piping Systems ◽  
The Many ◽  
Hot Melt

In the last decades, the use of adhesives has rapidly increased in many industrial fields. Adhesive joints are often preferred to traditional fasteners due to the many advantages that they offer. For instance, adhesive joints show a better stress distribution compared to the traditional fasteners and high mechanical properties under different loading conditions. Furthermore, they are usually preferred for joining components made of different materials. A wide variety of adhesives is currently available: thermoset adhesives are generally employed for structural joints but recently there has been a significant increment in the use of thermoplastic adhesives, in particular of the hot-melt adhesives (HMAs). HMAs permit to bond a large number of materials, including metal and plastics (e.g., polypropylene, PP), which can be hardly bonded with traditional adhesives. Furthermore, HMAs are characterized by a short open time and, therefore, permit for a quick and easy assembly process since they can be easily spread on the adherend surfaces by means of a hot-melt gun and they offer the opportunity of an ease disassembling process for repair and recycle. For all these reasons, HMAs are employed in many industrial applications and are currently used also for bonding polypropylene and polyolefin piping systems. In the present paper, the dynamic response of single lap joints (SLJ) obtained by bonding together with a polyolefin HMA two polypropylene substrates was experimentally assessed. Quasi-static tests and dynamic tests were carried out to investigate the strain rate effect: dynamic tests were carried out with a modified instrumented impact pendulum. Relevant changes in the joint performance have been put in evidence. Failure modes were finally analysed and compared. A change in the failure mode is experimentally found: in quasi-static tests SLJ failed due to a cohesive failure of the adhesive, whereas in dynamic tests the SLJ failed due to an interfacial failure, with a low energy absorption.

scholarly journals Hysteretic Behavior of Geopolymer Concrete with Active Confinement Subjected to Monotonic and Cyclic Axial Compression: An Experimental Study

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 3997 ◽  
Author(s):  
Huailiang Wang ◽  
Yuhui Wu ◽  
Min Wei ◽  
Lang Wang ◽  
Baoquan Cheng
Keyword(s):  
Failure Modes ◽  
Peak Stress ◽  
Hysteretic Behavior ◽  
Stress And Strain ◽  
Geopolymer Concrete ◽  
Cement Concrete ◽  
Cyclic Compression ◽  
Stress States ◽  
Loading Modes ◽  
Good Agreement

This paper investigated the performance of actively confined geopolymer concrete (GPC) through experiments. The mechanical properties of GPC under triaxial stress states were analyzed and discussed from the prospects of failure modes, axial peak stress and strain, monotonic and cyclic constitutive relationships. The experimental results demonstrated that the loading modes (monotonic loading and cyclic loading) had little effect on the failure mode and axial peak stress and strain. The improvement of the strength and ductility of GPC with the increase in confinement level was consistent with that of the conventional cement concrete while the strain enhancement of confined GPC was lower than that of confined conventional cement concrete at the same confinement level. The curves of the monotonic stress–strain and the envelop of cyclic compression were predicted through Mander’s model with good accuracy. The unloading/reloading models proposed by Lokuge were modified and the predicted cyclic hysteresis curves for actively confined GPC were in good agreement with the cyclic compression results. Findings from this study provide references for the application of geopolymer concrete.

Thermomechanical Simulation of Single Splat Solidification and Cooling in Plasma Spray Forming

2010 ◽  
Vol 102-104 ◽  
pp. 719-723
Author(s):  
Liang Rong Zhu ◽  
Hao Ping Zeng ◽  
Wen Ji Xu ◽  
Hong You Li
Keyword(s):  
Residual Stress ◽  
Plasma Spray ◽  
Steel Substrate ◽  
Element Model ◽  
Spray Forming ◽  
Plasma Spray Forming ◽  
Initial Stage ◽  
Minimum Residual ◽  
Thermomechanical Simulation ◽  
Stress States

Mechanical strength and service life of the coatings manufactured by plasma spray forming are significantly reduced by residual stresses. A 2D finite element model constructed for temperature and residual stress simulation of a single stainless steel splat solidifying and cooling on the carbon steel substrate is presented in this paper. Simulated results show that the temperature of the splat rim is higher than that of the central part during the initial stage of solidification, and the temperature difference between the two parts reverse thereafter. The minimum residual stress locates at the rim of the top surface of the splat, and the maximum residual stress, which decreases when the substrate is preheated to a higher temperature, situates at the rim of the interface. Stresses appear as tensile stresses within the splat and compressive stresses within the substrate. The research can provide quantitative understanding of the temperature and residual stress states at the splat level.

Sign in / Sign up

Export Citation Format

Share Document