scholarly journals Effect of Saturation and Post Processing on 3D Printed Calcium Phosphate Scaffolds

2008 ◽  
Vol 396-398 ◽  
pp. 663-666 ◽  
Author(s):  
Tamas D. Szucs ◽  
Dermot Brabazon
Keyword(s):  
Mechanical Properties ◽  
Calcium Phosphate ◽  
Sodium Phosphate ◽  
Three Dimensional ◽  
Surface Topology ◽  
Phosphate Solution ◽  
X Ray Diffraction ◽  
Three Dimensional Printing ◽  
Sodium Phosphate Solution ◽  
3D Printed

Three dimensional printing was investigated for fabricating hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) composite scaffolds using calcium phosphate based ceramics and calcium phosphate cement chemistry. Scaffolds were formed by printing an aqueous sodium phosphate solution on the powder bed consisting of a mixture of dicalcium phosphate anhydrous (DCPA) and calcium hydroxide powders. The sodium phosphate solution was functioning as a binder material and also as the initiator of the wet chemical reaction. Compressive mechanical properties of printed samples were examined as a function of saturation level that was inversely proportional to the powder to liquid ratio. To increase mechanical properties and obtain hydroxyapatite and β-TCP composites, the printed samples were sintered. The effect of sintering parameters including dwell time and sintering temperature were also examined. X-ray diffraction (XRD) was used to examine material composition at different stages of the manufacturing process and to confirm the presence of HA and β-TCP in the final stage. The effect of sintering procedure on the surface topology of the samples was examined using scanning electron microscopy (SEM).

Use of Three-dimensional Printing in the Development of Optimal Cardiac CT Scanning Protocols

2020 ◽  
Vol 16 (8) ◽  
pp. 967-977
Author(s):  
Zhonghua Sun
Keyword(s):  
Cardiovascular Disease ◽  
Cardiac Computed Tomography ◽  
Three Dimensional ◽  
Ct Scanning ◽  
Aortic Diseases ◽  
Clinical Value ◽  
Three Dimensional Printing ◽  
Doctor Patient Communication ◽  
Medical Education And Training ◽  
3D Printed

Three-dimensional (3D) printing is increasingly used in medical applications with most of the studies focusing on its applications in medical education and training, pre-surgical planning and simulation, and doctor-patient communication. An emerging area of utilising 3D printed models lies in the development of cardiac computed tomography (CT) protocols for visualisation and detection of cardiovascular disease. Specifically, 3D printed heart and cardiovascular models have shown potential value in the evaluation of coronary plaques and coronary stents, aortic diseases and detection of pulmonary embolism. This review article provides an overview of the clinical value of 3D printed models in these areas with regard to the development of optimal CT scanning protocols for both diagnostic evaluation of cardiovascular disease and reduction of radiation dose. The expected outcomes are to encourage further research towards this direction.

scholarly journals Three-dimensional printing for heart diseases: clinical application review

2021 ◽  
Author(s):  
Yanyan Ma ◽  
Peng Ding ◽  
Lanlan Li ◽  
Yang Liu ◽  
Ping Jin ◽  
...  
Keyword(s):  
3D Printing ◽  
Clinical Application ◽  
Heart Diseases ◽  
Three Dimensional ◽  
Convincing Evidence ◽  
Surgical Interventions ◽  
Three Dimensional Printing ◽  
Complex Anatomy ◽  
Precise Understanding ◽  
3D Printed

AbstractHeart diseases remain the top threat to human health, and the treatment of heart diseases changes with each passing day. Convincing evidence shows that three-dimensional (3D) printing allows for a more precise understanding of the complex anatomy associated with various heart diseases. In addition, 3D-printed models of cardiac diseases may serve as effective educational tools and for hands-on simulation of surgical interventions. We introduce examples of the clinical applications of different types of 3D printing based on specific cases and clinical application scenarios of 3D printing in treating heart diseases. We also discuss the limitations and clinically unmet needs of 3D printing in this context.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals Three-Dimensional Printing of Hydroxyapatite Composites for Biomedical Application

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 353
Author(s):  
Yanting Han ◽  
Qianqian Wei ◽  
Pengbo Chang ◽  
Kehui Hu ◽  
Oseweuba Valentine Okoro ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Biomedical Application ◽  
Three Dimensional ◽  
Antibacterial Properties ◽  
Natural Polymers ◽  
Three Dimensional Printing ◽  
3D Printed ◽  
Dental Applications ◽  
Hard Tissue Engineering

Hydroxyapatite (HA) and HA-based nanocomposites have been recognized as ideal biomaterials in hard tissue engineering because of their compositional similarity to bioapatite. However, the traditional HA-based nanocomposites fabrication techniques still limit the utilization of HA in bone, cartilage, dental, applications, and other fields. In recent years, three-dimensional (3D) printing has been shown to provide a fast, precise, controllable, and scalable fabrication approach for the synthesis of HA-based scaffolds. This review therefore explores available 3D printing technologies for the preparation of porous HA-based nanocomposites. In the present review, different 3D printed HA-based scaffolds composited with natural polymers and/or synthetic polymers are discussed. Furthermore, the desired properties of HA-based composites via 3D printing such as porosity, mechanical properties, biodegradability, and antibacterial properties are extensively explored. Lastly, the applications and the next generation of HA-based nanocomposites for tissue engineering are discussed.

scholarly journals Influence of the Infill Geometry of 3D-Printed Tablets on Drug Dissolution

2021 ◽  
Vol 5 (1) ◽  
pp. 15
Author(s):  
Nuno Venâncio ◽  
Gabriela G. Pereira ◽  
João F. Pinto ◽  
Ana I. Fernandes
Keyword(s):  
Three Dimensional ◽  
Drug Dissolution ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Preliminary Results ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Printing ◽  
Hot Melt ◽  
Patient Centric

Patient-centric therapy is especially important in pediatrics and may be attained by three-dimensional printing. Filaments containing 30% w/w of theophylline were produced by hot-melt extrusion and printed using fused deposition modelling to produce tablets. Here, preliminary results evaluating the effect of infill geometry (cross, star, grid) on drug content and release are reported.

Synthesis of Alpha-Tricalcium Phosphate by Wet Reaction and Evaluation of Mechanical Properties

2012 ◽  
Vol 727-728 ◽  
pp. 1164-1169 ◽  
Author(s):  
Mônica Beatriz Thürmer ◽  
Rafaela Silveira Vieira ◽  
Juliana Machado Fernandes ◽  
Wilbur Trajano Guerin Coelho ◽  
Luis Alberto Santos
Keyword(s):  
Mechanical Properties ◽  
Calcium Phosphate ◽  
Tricalcium Phosphate ◽  
Calcium Nitrate ◽  
Chemical Precipitation ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcium Phosphate Cements

Calcium phosphate cements have bioactivity and osteoconductivity and can be molded and replace portions of bone tissue. The aim of this work was to study the obtainment of α-tricalcium phosphate, the main phase of calcium phosphate cement, by wet reaction from calcium nitrate and phosphoric acid. There are no reports about α-tricalcium phosphate obtained by this method. Two routes of chemical precipitation were evaluated and the use of two calcinations temperatures to obtain the phase of cement. The influence of calcination temperature on the mechanical properties of cement was evaluated. Cement samples were characterized by particle size analysis, X-ray diffraction, mechanical strength and scanning electron microscopy. The results demonstrate the strong influence of synthesis route on the crystalline phases of cement and the influence of concentration of reactants on the product of the reaction, as well as, on the mechanical properties of cement.

Additive manufactured multi-material structure with directional specific mechanical properties based upon classical lamination theory

2018 ◽  
Vol 24 (7) ◽  
pp. 1212-1220 ◽  
Author(s):  
Sugavaneswaran M. ◽  
Arumaikkannu G.
Keyword(s):  
Mechanical Properties ◽  
Three Dimensional ◽  
Additive Manufacture ◽  
Material Structure ◽  
Loading Conditions ◽  
Content Type ◽  
Three Dimensional Printing ◽  
Classical Lamination Theory ◽  
Innovative Methodology ◽  
Lamination Theory

Purpose This paper aims to additive manufacture (AM) the multi-material (MM) structure with directional-specific mechanical properties based on the classical lamination theory of composite materials. Design/methodology/approach The polyjet three-dimensional printing (3DP) process is used to fabricate the MM structure with directional-specific mechanical properties. MMs within a layer are positioned and oriented based on the classical lamination theory to achieve directional-specific properties. Mechanical behavior of the AM structure was examined under various loading conditions to justify the directional-specific properties. Findings With MM processing capabilities of the polyjet 3DP machine, AM MM structures with directional-specific mechanical properties were fabricated. From experimentation, it was observed that the AM MM structure with a quasi-isotropic laminate has superior tensile and flexural strength, and the AM MM structure with an angle ply laminate has superior shear strength. Various mechanical properties determined through testing will be useful for the selection of an appropriate layup arrangement within a structure for appropriate loading conditions. Originality/value This study presents the innovative methodology for the fabrication of AM MM structures with tailor-made mechanical properties. The developed methodology paves way for using the polyjet 3DP MM structure for applications such as the complaint mechanism, snap fits and thin features, which require directional-specific properties.

Sign in / Sign up

Export Citation Format

Share Document