Investigate of Performance of Asphalt Concrete with Gneiss

2009 ◽  
Vol 417-418 ◽  
pp. 497-500 ◽  
Author(s):  
Ling Pang ◽  
Shao Peng Wu ◽  
Jun Xie ◽  
De Ming Hu
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Processing Property ◽  
Bending Fatigue ◽  
Tensile Strength Test ◽  
Four Point Bending ◽  
Bending Fatigue Test ◽  
Indirect Tensile

The use of gneiss as aggregates might help meet the pavement constructing demands. However, the study of the pavement performances of gneiss asphalt mixture is few. In this paper, the microstructure of gneiss aggregate was studied by Scanning Electron Microscopy (SEM). And the pavement performances of gneiss asphalt mixture with different improving measure were characterized by means of Indirect Tensile Strength Test and Four-Point Bending Fatigue Test. Gneiss is flaky, surface texture rougher and imporosity characteristic in microstructure, resulting to its adhesion and processing property are poor. Experiment results indicate that the use of hydrated lime replacing limestone power partly in filler can improve pavement properties of the gneiss asphalt mixtures distinctly.

scholarly journals Performance Evaluation of Warm- and Hot-Mix Asphalt Mixtures Based on Laboratory and Accelerated Pavement Tests

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
Yongjoo Kim ◽  
Jaejun Lee ◽  
Cheolmin Baek ◽  
Sunglin Yang ◽  
Sooahn Kwon ◽  
...  
Keyword(s):  
Asphalt Mixture ◽  
Warm Mix Asphalt ◽  
Strength Test ◽  
Asphalt Mixtures ◽  
Limited Data ◽  
Tensile Strength Test ◽  
Paving Asphalt ◽  
Dynamic Modulus Test ◽  
Indirect Tensile ◽  
Lower Temperature

A number of warm-mix asphalt (WMA) technologies are used to reduce the temperature at which the asphalt mixtures are produced and compacted, apparently without compromising the performance of the pavement. The main objective of this study is to determine whether the use of an innovative wax-based LEADCAP WMA additive influences the performance of the asphalt mixture, which is produced and compacted at significantly low temperatures. The WMA pavement using LEADCAP additive (WMA-LEADCAP) along with a control HMA pavement was evaluated with respect to their performances of rutting resistance, crack resistance, and viscoelastic property based on the laboratory dynamic modulus test, indirect tensile strength test, and in-door accelerated pavement test (APT) results. With the limited data carried out, the LEADCAP additive is effective in producing and paving asphalt mixture at approximately 30°C lower temperature than a control HMA mixture, and the performances of WMA-LEADCAP pavement are comparable to a control HMA pavement.

scholarly journals Effect of Aggregate Gradation on the Stiffness of Asphalt Mixtures

2015 ◽  
Vol 16 (2) ◽  
pp. 39-49 ◽  
Author(s):  
Hasan Al-Mosawe ◽  
Nick Thom ◽  
Gordon Airey ◽  
Amjad Al-Bayati
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Volumetric Properties ◽  
Aggregate Gradation ◽  
Effect Of Particle Size ◽  
Indirect Tensile

Abstract Aggregate gradation plays an important role in the behaviour of asphalt mixtures. Packing of aggregate is a very important factor that will be affected by changing the aggregate gradation. Many researchers have investigated different ways of describing packing both theoretically and practically. Bailey ratios have recently been used to understand the volumetric properties of mixtures. In this paper, the Bailey ratios have been used, and two further ratios have also been introduced to allow the asphalt mixture gradation to be fully understood. Thirteen different aggregate gradations have been chosen within the 14 mm asphalt concrete specification to investigate the effect of particle size distribution on the stiffness of the mixture. It was found that variation in aggregate gradation has a significant effect on asphalt stiffness, even within specification limits, and a reasonable correlation between the set of ratios investigated and the Indirect Tensile Stiffness.

scholarly journals Evaluations of Nano-Sized Hydrated Lime on the Moisture Susceptibility of Hot Mix Asphalt Mixtures

2012 ◽  
Vol 174-177 ◽  
pp. 82-90 ◽  
Author(s):  
Ju Nan Shen ◽  
Zhao Xing Xie ◽  
Fei Peng Xiao ◽  
Wen Zhong Fan
Keyword(s):  
Tensile Strength ◽  
Experimental Design ◽  
Hot Mix Asphalt ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Moisture Resistance ◽  
Strength Ratio ◽  
Moisture Susceptibility ◽  
Indirect Tensile

The objective of this study was to evaluate the effect of nano-sized hydrated lime on the moisture susceptibility of the hot mix asphalt (HMA) mixtures in terms of three methodologies to introduce into the mixtures. The experimental design for this study included the utilizations of one binder source (PG 64-22), three aggregate sources and three different methods introducing the lime. A total of 12 types of HMA mixtures and 72 specimens were fabricated and tested in this study. The performed properties include indirect tensile strength (ITS), tensile strength ratio (TSR), flow, and toughness. The results indicated that the nano-sized lime exhibits better moisture resistance. Introducing process of the nano-sized lime will produce difference in moisture susceptibility.

scholarly journals Laboratory Evaluation of the Use of Florida Washed Shell in Open-Graded Asphalt Mixtures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7060
Author(s):  
Mohammad Alharthai ◽  
Qing Lu ◽  
Ahmed Elnihum ◽  
Asad Elmagarhe
Keyword(s):  
Tensile Strength ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Laboratory Evaluation ◽  
Void Content ◽  
Coarse Aggregates ◽  
Significant Difference ◽  
Indirect Tensile ◽  
Marshall Stability

This study investigates the substitution of conventional aggregate with a Florida washed shell in open-graded asphalt mixtures and evaluates the optimal substitution percentage in aggregate gradations of various nominal maximum aggregate sizes (NMASs) (i.e., 4.75, 9.5, and 12.5 mm). Laboratory experiments were performed on open-graded asphalt mixture specimens with the coarse aggregate of sizes between 2.36 and 12.5 mm being replaced by the Florida washed shell at various percentages (0, 15, 30, 45, and 100%). Specimen properties relevant to the performance of open-graded asphalt mixtures in the field were tested, evaluated, and compared. Specifically, a Marshall stability test, Cantabro test, indirect tensile strength test, air void content test, and permeability test were conducted to evaluate the strength, resistance to raveling, cracking resistance, void content, and permeability of open-graded asphalt mixtures. The results show that there is no significant difference in the Marshall stability and indirect tensile strength when the coarse aggregates are replaced with Florida washed shell. This study also found that the optimum percentages of Florida washed shell in open-graded asphalt mixture were 15, 30, and 45% for 12.5, 9.5, and 4.75 mm NMAS gradations, respectively.

scholarly journals Study on Fatigue Test and Life Prediction of Polyurethane Cement Composite (PUC) under High or Low Temperature Conditions

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Hongshuai Gao ◽  
Quansheng Sun
Keyword(s):  
Fatigue Life ◽  
Fatigue Test ◽  
Asphalt Mixture ◽  
Cement Composite ◽  
Control Mode ◽  
Fatigue Properties ◽  
Coupling Condition ◽  
Bending Fatigue ◽  
Bending Fatigue Test ◽  
Steel Deck

There are many diseases in the deck pavement of long-span steel bridges under the action of vehicles, rainwater, and freezing. It is necessary to study a new type of pavement material with high waterproof property, light weight, and high bonding performance for steel deck pavement. Polyurethane cement composite (PUC) can be used for steel deck pavement. In order to find out the temperature effect on fatigue properties of PUC, the four-point bending fatigue test was carried out at different temperatures. In this paper, the optimum mix ratio of PUC was selected by compressive and flexural tests, and then the bending fatigue test was conducted under strain control mode. Under temperature and external force coupling condition, a method for predicting fatigue life of PUC is proposed by the combination of theoretical deduction and experimental research. The results show that the proposed formula can effectively describe the fatigue life and fatigue limit of PUC. Finally, compared with three different asphalt mixtures for steel deck pavement, it is found that the fatigue performance of polyurethane cement is better than that of asphalt mixture.

scholarly journals Determination of Construction Parameters of Porous Ultra-Thin Overlays Based on Laboratory Compaction Studies

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4496
Author(s):  
Jiahao Tian ◽  
Sang Luo ◽  
Ziming Liu ◽  
Xu Yang ◽  
Qing Lu
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Combination Method ◽  
Compaction Temperature ◽  
Pavement Maintenance ◽  
Energy Equivalence ◽  
New Type ◽  
Better Than

To address the severe distresses of asphalt pavement, a new type of pavement maintenance treatment, porous ultra-thin overlay (PUTO) with small particle size was proposed. The PUTO has a thickness of 1.5–2.5 cm and a large void ratio of 18–25%. As a newly asphalt mixture, the structure characteristics differ from poor traditional pavement. Therefore, it is necessary to investigate the fabrication schemes in laboratory and on-site, respectively. In this study, the optimal fabrication schemes, including compaction temperature and number of blows of PUTO were determined based on Cantabro test and volumetric parameters. Then, the corresponding relationship between laboratory and on-site compaction work was then established based on the energy equivalent principle. On this basis, the numbers of on-site rolling passes and the combination method were calculated. The results show that increased compaction temperature and number of blows reduce the height and enhance the compaction of the Marshall sample. With the same temperature and number of blows, the raveling resistance of coarse gradation, Pavement Asphalt Concrete-1 (PAC-1) is better than that of fine gradation, Pavement Asphalt Concrete-2 (PAC-2), and the increased asphalt viscosity significantly improves the raveling resistance of the asphalt mixture. To ensure the scattering resistance and volumetric characteristic, the initial compaction temperature of the PAC-1 and PAC-2 should not be lower than 150 °C and 165 °C, respectively. Then, the laboratory compaction work and on-site compaction work were calculated and converted based on the principle of energy equivalence. Consequently, the on-site compaction combination of rolling machines for four asphalt mixtures was determined. According to the volumetric parameters, the paving test section proved that the construction temperature and the on-site rolling combination determined by laboratory tests are reasonable, and ultra-thin overlay has good structural stability, drainage, and skid resistance.

scholarly journals Effect of Hydrated Lime on Indirect Tensile Stiffness Modulus of Asphalt Concrete Produced in Half-Warm Mix Technology

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4731
Author(s):  
Mateusz M. Iwański
Keyword(s):  
Asphalt Concrete ◽  
Permanent Deformation ◽  
Active Agent ◽  
Hydrated Lime ◽  
Partial Replacement ◽  
Stiffness Modulus ◽  
Limestone Filler ◽  
Tensile Stiffness ◽  
Lime Content ◽  
Indirect Tensile

Half-warm mix asphalt (HWMA) mixtures can be produced at temperatures ranging from 100 °C to 130 °C, depending on the production methods used. The lowest mixing temperature can be achieved by using water-foamed bitumen. The mixture should be characterized by a long service life, defined by the resistance to permanent deformation and high stiffness modulus at temperatures above zero. It is therefore important to ensure the adequately high quality of the bitumen binder. Bitumen 50/70 was provided with appropriate quality foaming characteristics (expansion ratio, ER, half-life, t1/2) by adding a surface-active agent (SAA) at 0.6 wt % before foaming. Then asphalt concrete (AC) 8 S was designed and produced with the recommended water-foamed binder. Hydrated lime, an additive substantially affecting asphalt concrete mechanical parameters, was used at 0, 15, 30, and 45 wt % as a partial replacement for the limestone filler. The influence of the amount of hydrated lime on the content of voids, indirect tensile stiffness modulus at −10 °C, 0 °C, +10 °C, +20 °C, and +30 °C, and the resistance to permanent deformation was investigated. Statistical analysis of the test results showed the quantity of 30% to be the optimum hydrated lime content. The AC 8 S resistance to permanent deformation was determined at the optimum hydrated lime content. The comprehensive evaluation revealed a synergistic effect between bitumen 50/70, modified before foaming with 0.6 wt % SAA and 30 wt % hydrated lime as the limestone filler replacement, and the half warm mixture AC 8 S, in terms of the standard requirements and durability of the HWMA concrete in pavement applications.

Sign in / Sign up

Export Citation Format

Share Document