Investigations on Degradable and Figuline Calcium Alkaline Phosphate Cements with Multimodal Particle Size Distribution

2011 ◽  
Vol 493-494 ◽  
pp. 355-360
Author(s):  
F. Dombrowski ◽  
R. Hoffmann ◽  
Ute Ploska ◽  
Heidi Marx ◽  
Georg Berger
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Setting Time ◽  
Volume Ratio ◽  
Particle Sizes ◽  
Powder Mixtures ◽  
Setting Reaction ◽  
Tap Density

The paper presented here deals with rheological and hardening properties during the setting reaction, and density and compressive strength after the final setting of a figuline composite consisting of Ca2KNa(PO4)2and 2wt% medium gel strength gelatin. Compared to the composite with monomodal particle size distribution (d50=7.18µm; span=3.9) and its properties during and after setting reaction, the goal of this work is to increase the resulting product compressive strength by mixing different particle sizes in order to obtain bi- and trimodal distributions. For the bimodal powder mixtures the ratio in diameter (dcourse/dsmall) was chosen with 7/1 and volume ratio dcourse/dsmallwas 70/30%. For the trimodal powder mixtures the ratio in diameter (dcourse/dmedium/dsmall) was chosen with 70/7/1 and volume ratio dcourse/dmedium/dsmallwas set to 44/28/28%.After establishing an adequate crushing and sieving process the tap density and powder density of each fraction was determined. Subsequently, the different particle sizes were mixed and the densities and the Hausner ratio were determined again. The mixtures show an increase in both densities especially the tap density increased significantly. Rheological investigations show that the graphs of storage and loss moduli of the multimodal powder mixtures respectively are similar. The characteristic setting times show a slight decrease compared with the monomodal composite but not significantly different data. When comparing the resulting compressive strength of cylindrical samples, which were stored direct after reaching the initial setting time under physiological conditions, the studies illustrated in all cases for the multimodal mixtures a significant increase in compressive strength and a higher density.

scholarly journals Influence of Particle Size Distribution of High Calcium Fly Ash on HVFA Mortar Properties

2018 ◽  
Vol 20 (2) ◽  
pp. 51
Author(s):  
Antoni . ◽  
Hendra Surya Wibawa ◽  
Djwantoro Hardjito
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Fly Ash ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Setting Time ◽  
High Volume ◽  
High Volume Fly Ash ◽  
High Calcium ◽  
High Calcium Fly Ash

This study evaluates the effect of particle size distribution (PSD) of high calcium fly ash on high volume fly ash (HVFA) mortar characteristics. Four PSD variations of high calcium fly ash used were: unclassified fly ash and fly ash passing sieve No. 200, No. 325 and No. 400, respectively. The fly ash replacement ratio of the cementitious material ranged between 50-70%. The results show that with smaller fly ash particles size and higher levels of fly ash replacement, the workability of the mixture was increased with longer setting time. There was an increase in mortar compressive strength with finer fly ash particle size, compared to those with unclassified ones, with the highest strength was found at those with fly ash passing mesh No. 325. The increase was found due to better compactability of the mixture. Higher fly ash replacement reduced the mortar’s compressive strength, however, the rate was reduced when finer fly ash particles was used.

scholarly journals Grinding Kinetics of Slag and Effect of Final Particle Size on the Compressive Strength of Alkali Activated Materials

Minerals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 714 ◽  
Author(s):  
Evangelos Petrakis ◽  
Vasiliki Karmali ◽  
Georgios Bartzas ◽  
Konstantinos Komnitsas
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Ageing Time ◽  
Reduction Rate ◽  
Curing Temperature ◽  
Alkali Activation ◽  
Final Particle ◽  
Alkali Activated

This study aims to model grinding of a Polish ferronickel slag and evaluate the particle size distributions (PSDs) of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e., temperature, curing, and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin–Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multifractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

scholarly journals Phase evolution, characterisation, and performance of cement prepared in an oxy-fuel atmosphere

2016 ◽  
Vol 192 ◽  
pp. 113-124 ◽  
Author(s):  
Liya Zheng ◽  
Thomas P. Hills ◽  
Paul Fennell
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Carbon Capture ◽  
Raw Materials ◽  
Carbon Capture And Storage ◽  
Phase Evolution ◽  
Chemical Compositions ◽  
Phase And Elemental Compositions

Cement manufacture is one of the major contributors (7–10%) to global anthropogenic CO2 emissions. Carbon capture and storage (CCS) has been identified as a vital technology for decarbonising the sector. Oxy-fuel combustion, involving burning fuel in a mixture of recycled CO2 and pure O2 instead of air, makes CO2 capture much easier. Since it combines a theoretically lower energy penalty with an increase in production, it is attractive as a CCS technology in cement plants. However, it is necessary to demonstrate that changes in the clinkering atmosphere do not reduce the quality of the clinker produced. Clinkers were successfully produced in an oxy-fuel atmosphere using only pure oxides as raw materials as well as a mixture of oxides and clay. Then, CEM I cements were prepared by the addition of 5 wt% gypsum to the clinkers. Quantitative XRD and XRF were used to obtain the phase and elemental compositions of the clinkers. The particle size distribution and compressive strength of the cements at 3, 7, 14, and 28 days' ages were tested, and the effect of the particle size distribution on the compressive strength was investigated. Additionally, the compressive strength of the cements produced in oxy-fuel atmospheres was compared with those of the cement produced in air and commercially available CEMEX CEM I. The results show that good-quality cement can be successfully produced in an oxy-fuel atmosphere and it has similar phase and chemical compositions to CEM I. Additionally, it has a comparable compressive strength to the cement produced in air and to commercially available CEMEX CEM I.

Ultra-Durable Concretes: Structure at the Micro- and Nanoscale

MRS Bulletin ◽  
2004 ◽  
Vol 29 (5) ◽  
pp. 324-327 ◽  
Author(s):  
Christian P. Vernet
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Fiber Reinforced ◽  
Remarkable Improvement ◽  
Load Carrying ◽  
Wide Particle Size Distribution

AbstractUltrahigh-performance concretes (UHPCs) are obtained by optimizing several technologies: minimizing the amount of water added, using superplasticizers and a wide particle size distribution, and packing the particles to improve fluidity with minimized water additions and to optimize load-carrying capacity. Fibers can be incorporated to increase ductility, leading to ultrahigh-performance fiber-reinforced concretes (UHPFRCs). Such enhanced concretes can approach the compressive strength of steel, with a remarkable improvement in durability. UHPCs offer new solutions for innovative construction, especially in aggressive environments.

scholarly journals MINERAL ABUNDANCE AND PARTICLE SIZE DISTRIBUTION DERIVED FROM IN-SITU SPECTRA MEASUREMENTS OF YUTU ROVER OF CHANG’E-3

2017 ◽  
Vol XLII-3/W1 ◽  
pp. 85-89
Author(s):  
H. Lin ◽  
X. Zhang ◽  
Y. Yang ◽  
X. Wu ◽  
D. Guo
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Landing Site ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Particle Sizes ◽  
The Mean ◽  
The Difference ◽  
Yutu Rover

From geologic perspective, understanding the types, abundance, and size distributions of minerals allows us to address what geologic processes have been active on the lunar and planetary surface. The imaging spectrometer which was carried by the Yutu Rover of Chinese Chang’E-3 mission collected the reflectance at four different sites at the height of ~ 1 m, providing a new insight to understand the lunar surface. The mineral composition and Particle Size Distribution (PSD) of these four sites were derived in this study using a Radiative Transfer Model (RTM) and Sparse Unmixing (SU) algorithm. The endmembers used were clinopyroxene, orthopyroxene, olivine, plagioclase and agglutinate collected from the lunar sample spectral dataset in RELAB. The results show that the agglutinate, clinopyroxene and olivine are the dominant minerals around the landing site. In location Node E, the abundance of agglutinate can reach up to 70 %, and the abundances of clinopyroxene and olivine are around 10 %. The mean particle sizes and the deviations of these endmembers were retrieved. PSDs of all these endmembers are close to normal distribution, and differences exist in the mean particle sizes, indicating the difference of space weathering rate of these endmembers.

scholarly journals Particle size distribution of sawdust and wood shavings mixtures

2010 ◽  
Vol 56 (No. 4) ◽  
pp. 154-158 ◽  
Author(s):  
T. Vítěz ◽  
P. Trávníček
Keyword(s):  
Experimental Data ◽  
Particle Size ◽  
Distribution Function ◽  
Network Analysis ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Mass Fraction ◽  
Particle Sizes ◽  
Wood Shavings ◽  
Number Of Particles

Particle size distribution of the sample of waste sawdust and wood shavings mixtures were made with two commonly used methods of mathematical models by Rosin-Rammler (RR model) and by Gates-Gaudin-Schuhmann (GGS model).On the basis of network analysis distribution function F (d) (mass fraction) and density function f (d) (number of particles captured between two screens) were obtained. Experimental data were evaluated using the RR model and GGS model, both models were compared. Better results were achieved with GGS model, which leads to a more accurate separation of the different particle sizes in order to obtain a better industrial profit of the material.

Hierarchical Li-rich oxide microspheres assembled from {010} exposed primary grains for high-rate lithium-ion batteries

2020 ◽  
Vol 44 (20) ◽  
pp. 8486-8493 ◽  
Author(s):  
Zhongyue Zi ◽  
Yantao Zhang ◽  
Yangqian Meng ◽  
Ge Gao ◽  
Peiyu Hou
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Lithium Ion Batteries ◽  
Size Distribution ◽  
Lithium Ion ◽  
High Rate ◽  
Tap Density ◽  
Wide Particle Size Distribution

The wide particle size distribution of LLO microspheres assembled from {010} exposed primary grains is proposed to improve their Li+ kinetics and tap-density.

Sign in / Sign up

Export Citation Format

Share Document