scholarly journals A Generalized Method for Flat Plates Impact Detection and Location

2013 ◽  
Vol 543 ◽  
pp. 171-175
Author(s):  
Jose Andrés Somolinos ◽  
Rafael Morales ◽  
Carlos Morón ◽  
Alfonso Garcia
Keyword(s):  
Signal Processing ◽  
Flat Plate ◽  
Acoustic Signal ◽  
Experimental Results ◽  
Piezoelectric Sensors ◽  
Experimental Setup ◽  
Flat Plates ◽  
Impact Detection ◽  
Timing Difference

In the last years, many analyses from acoustic signal processing have been used for different applications. In most cases, these sensor systems are based on the determination of times of flight for signals from every transducer. This paper presents a flat plate generalization method for impact detection and location over linear links or bars-based structures. The use of three piezoelectric sensors allow to achieve the position and impact time while the use of additional sensors lets cover a larger area of detection and avoid wrong timing difference measurements. An experimental setup and some experimental results are briefly presented.

Towards the Understanding of Manifold Fluttering During Pendulous Installation: Flow Induced Rotation of Flat Plates in Uniform Flow

2010 ◽  
Author(s):  
Antonio Carlos Fernandes ◽  
Sina Mirzaei Sefat ◽  
Fabio Moreira Coelho ◽  
Mario Ribeiro
Keyword(s):  
Flat Plate ◽  
Rio De Janeiro ◽  
Center Of Pressure ◽  
Numerical Models ◽  
Free Fall ◽  
Reynolds Numbers ◽  
Uniform Flow ◽  
Experimental Results ◽  
Flat Plates ◽  
Drag And Lift

The pendulous installation method of a manifold has a first phase that can be considered as a free fall in water. Of course, this is not free due to the fluid action. The consequence is that the manifold may oscillate rotationally which characterizes a fluttering behavior. However, the manifold is a complex body with non-uniform shape, several modules, porosity etc. Hence, in order to improve the understanding of the fluttering, this work presents advances in the observation of flow induced rotation on a flat plate in uniform flow. This has been started experimentally and subsequently numerical models yielded a confirmation of quasi-steady observations. The experimental results were obtained at the Laborato´rio de Ondas e Correntes (LOC) [Laboratory of Waves and Current] in COPPE/Federal University of Rio de Janeiro. The drag and lift forces coefficients and the center of pressure have been obtained for angles of attack θ = 0°–90° and for different Reynolds numbers.

Shear-moment transfer in flat plates

1986 ◽  
Vol 13 (3) ◽  
pp. 327-334
Author(s):  
Sidney H. Simmonds ◽  
Brian W. Doblanko
Keyword(s):  
Shear Stress ◽  
Flat Plate ◽  
Key Words ◽  
Concrete Slabs ◽  
Shear Stresses ◽  
Flat Plates ◽  
Design Factor ◽  
Critical Design ◽  
Design Charts

For many concrete slabs without beams, the critical design factor is the shear stress in the vicinity of the column–slab junction. This is particularly so near edge and corner columns where the shear stresses due to the unbalanced moments may account for the major portion of these stresses. The determination of these design stresses in accordance with the provisions of Standard CAN3-A23.3-M84 is both time consuming and subject to numerical mistakes. Based on these provisions, design charts were developed, which greatly reduce the amount of calculation required and are suitable for routine use in the design of slabs. The use of the charts is illustrated by examples. Key words: design, flat plate, moment transfer, reinforced concrete, shear, slabs.

Determination of Charge Coefficient of Piezoelectric Films Using a Combined Finite Element Model and Dynamic Loading Technique

2020 ◽  
Vol 835 ◽  
pp. 229-242
Author(s):  
Oboso P. Bernard ◽  
Nagih M. Shaalan ◽  
Mohab Hossam ◽  
Mohsen A. Hassan
Keyword(s):  
Finite Element ◽  
Dynamic Loading ◽  
Material Properties ◽  
Accurate Determination ◽  
Substrate Material ◽  
Experimental Results ◽  
Piezoelectric Composite ◽  
Piezoelectric Film ◽  
Piezoelectric Charge

Accurate determination of piezoelectric properties such as piezoelectric charge coefficients (d33) is an essential step in the design process of sensors and actuators using piezoelectric effect. In this study, a cost-effective and accurate method based on dynamic loading technique was proposed to determine the piezoelectric charge coefficient d33. Finite element analysis (FEA) model was developed in order to estimate d33 and validate the obtained values with experimental results. The experiment was conducted on a piezoelectric disc with a known d33 value. The effect of measuring boundary conditions, substrate material properties and specimen geometry on measured d33 value were conducted. The experimental results reveal that the determined d33 coefficient by this technique is accurate as it falls within the manufactures tolerance specifications of PZT-5A piezoelectric film d33. Further, obtained simulation results on fibre reinforced and particle reinforced piezoelectric composite were found to be similar to those that have been obtained using more advanced techniques. FE-results showed that the measured d33 coefficients depend on measuring boundary condition, piezoelectric film thickness, and substrate material properties. This method was proved to be suitable for determination of d33 coefficient effectively for piezoelectric samples of any arbitrary geometry without compromising on the accuracy of measured d33.

scholarly journals A parametric prediction of the Young’s modulus of polymers enhanced with ΜWCNTs

2018 ◽  
Vol 233 ◽  
pp. 00025
Author(s):  
P.V. Polydoropoulou ◽  
K.I. Tserpes ◽  
Sp.G. Pantelakis ◽  
Ch.V. Katsiropoulos
Keyword(s):  
Young’S Modulus ◽  
Elastic Properties ◽  
Young's Modulus ◽  
Experimental Results ◽  
Scale Model ◽  
Fe Model ◽  
Multi Scale ◽  
Unit Cells ◽  
Random Dispersion

In this work a multi-scale model simulating the effect of the dispersion, the waviness as well as the agglomerations of MWCNTs on the Young’s modulus of a polymer enhanced with 0.4% MWCNTs (v/v) has been developed. Representative Unit Cells (RUCs) have been employed for the determination of the homogenized elastic properties of the MWCNT/polymer. The elastic properties computed by the RUCs were assigned to the Finite Element (FE) model of a tension specimen which was used to predict the Young’s modulus of the enhanced material. Furthermore, a comparison with experimental results obtained by tensile testing according to ASTM 638 has been made. The results show a remarkable decrease of the Young’s modulus for the polymer enhanced with aligned MWCNTs due to the increase of the CNT agglomerations. On the other hand, slight differences on the Young’s modulus have been observed for the material enhanced with randomly-oriented MWCNTs by the increase of the MWCNTs agglomerations, which might be attributed to the low concentration of the MWCNTs into the polymer. Moreover, the increase of the MWCNTs waviness led to a significant decrease of the Young’s modulus of the polymer enhanced with aligned MWCNTs. The experimental results in terms of the Young’s modulus are predicted well by assuming a random dispersion of MWCNTs into the polymer.

scholarly journals Application of UAV in Search and Rescue Actions in Underground Mine—A Specific Sound Detection in Noisy Acoustic Signal

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3725
Author(s):  
Paweł Zimroz ◽  
Paweł Trybała ◽  
Adam Wróblewski ◽  
Mateusz Góralczyk ◽  
Jarosław Szrek ◽  
...  
Keyword(s):  
Signal Processing ◽  
Acoustic Signal ◽  
Processing Technique ◽  
Underground Mine ◽  
Search And Rescue ◽  
Reference Spectrum ◽  
Signal Processing Technique ◽  
Time Frequency ◽  
Communication Device ◽  
Frequency Representation

The possibility of the application of an unmanned aerial vehicle (UAV) in search and rescue activities in a deep underground mine has been investigated. In the presented case study, a UAV is searching for a lost or injured human who is able to call for help but is not able to move or use any communication device. A UAV capturing acoustic data while flying through underground corridors is used. The acoustic signal is very noisy since during the flight the UAV contributes high-energetic emission. The main goal of the paper is to present an automatic signal processing procedure for detection of a specific sound (supposed to contain voice activity) in presence of heavy, time-varying noise from UAV. The proposed acoustic signal processing technique is based on time-frequency representation and Euclidean distance measurement between reference spectrum (UAV noise only) and captured data. As both the UAV and “injured” person were equipped with synchronized microphones during the experiment, validation has been performed. Two experiments carried out in lab conditions, as well as one in an underground mine, provided very satisfactory results.

A Technique for the Laboratory Determination of Recirculation in Single Needle Dialysis

1993 ◽  
Vol 16 (2) ◽  
pp. 63-70 ◽  
Author(s):  
N.A. Hoenich ◽  
P.T. Smirthwaite ◽  
C. Woffindin ◽  
P. Lancaster ◽  
T.H. Frost ◽  
...  
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Experimental Results ◽  
New Technique ◽  
Treatment Efficiency ◽  
Single Lumen ◽  
Theoretical Predictions ◽  
Lumen Catheter ◽  
A New Technique

Recirculation is an important factor in single needle dialysis and, if high, can compromise treatment efficiency. To provide information regarding recirculation characteristics of access devices used in single needle dialysis, we have developed a new technique to characterise recirculation and have used this to measure the recirculation of a Terumo 15G fistula needle and a VasCath SC2300 single lumen catheter. The experimentally obtained results agreed well with those established clinically (8.5 ± 2.4% and 18.4 ± 3.4%). The experimental results have also demonstrated a dependence on access type, pump speeds and fistula flow rate. A comparison of experimental data with theoretical predictions showed that the latter exceeded those measured with the largest contribution being due to the experimental fistula.

Sign in / Sign up

Export Citation Format

Share Document