Effect of Curing Pressure on Compression and Consolidation Behaviors of Cement Admixed Clay

2017 ◽  
Vol 744 ◽  
pp. 71-76 ◽  
Author(s):  
Anuchit Uchaipichat
Keyword(s):  
Atmospheric Pressure ◽  
Laboratory Tests ◽  
Void Ratio ◽  
Cement Content ◽  
Confining Pressure ◽  
Coefficient Of Consolidation ◽  
Cemented Soil ◽  
Preconsolidation Pressure ◽  
Recompression Index ◽  
Curing Pressure

The cemented soils are typically produced and cured under confining pressure of soil. The cemented soil properties are, however, obtained from laboratory tests on the cement admixed clay samples cured under atmospheric pressure. Thus, the parameters of cemented soil obtained from laboratory tests are not representative of the actual values in the field. In this research, a series of consolidation tests using oedometer apparatus on cement admixed clay samples with different curing pressure conditions was carried out. The samples was cured under pressure values of 0 kPa (atmospheric pressure) and 50 kPa. The test samples with values of cement content of 0, 1 and 2 percent were cured for 28 days before testing. The compression curves of cement admixed kaolin showed the elasto-plastic deformation in all cases of the tests. It was found that the range of void ratio of the samples with curing pressure of 0 kPa (atmospheric pressure) was higher than that of the samples with curing pressure of 50 kPa. With increasing curing pressure and cement content, the value of recompression index decreased while the value of compression index was approximately constant. It was also observed that the preconsolidation pressure increased with increasing cement content for both cases of curing pressure. It should be noted that the values of preconsolidation pressure increased with increasing curing pressure. Moreover, the values of coefficient of consolidation decreased with increasing effective vertical stress in all cases. It was also found that the values of coefficient of consolidation increased with increasing curing pressure and cement content.

Influence of Curing Pressure on Unconfined Compressive Strength of Cemented Clay

2018 ◽  
Vol 928 ◽  
pp. 263-268 ◽  
Author(s):  
Anuchit Uchaipichat
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Soft Clay ◽  
Peak Stress ◽  
Confining Pressure ◽  
Compression Tests ◽  
Unconfined Compression ◽  
Soil Cement ◽  
Curing Pressure

The soil-cement columns are generally installed and cured in the soft clay layers under confining pressure. The strength of the soil-cement columns may be influenced by confining pressure during curing period. In this study, the main objective was to study the influence of curing pressure on unconfined compressive strength of cemented clay. A series of unconfined compression tests was performed on a cement admixed clay sample cured under pressure values of 0 kPa (atmospheric pressure), 25kPa, 50kPa and 100 kPa using a typical unconfined compression equipment. The test samples with values of cement content of 0.5, 1.0 and 2.0 percent were cured for 28 days.The stress-strain curves obtained from all tests show a peak value of stress. The unconfined compressive strength or peak stress obviously increased with increasing cement content for all curing pressure conditions. It can be observed that the strength of samples gradually increased with curing pressure for cement content of 0.5 percent. For cement contents of 1.0 and 2.0 percent, the strengths of samples cured under pressures of 25 kPa dramatically increased from the strength of samples cured without pressure (0 kPa), however, the strengths of samples for curing pressures of 25, 50 and 100 kPa were not clearly different.

Consolidation Properties of Ho Chi Minh City Soil, Vietnam

2020 ◽  
Vol 54 (1A) ◽  
pp. 1-10
Author(s):  
Vo Nhat Luan
Keyword(s):  
Void Ratio ◽  
Soft Soil ◽  
Liquid Limit ◽  
Ho Chi Minh City ◽  
Compression Index ◽  
Underground Structures ◽  
Compression Pressure ◽  
Coefficient Of Consolidation ◽  
Two Samples ◽  
Index Changes

This paper presents the experimental results of consolidation properties of soft soil in Ho Chi Minh City of Vietnam. Forty-two samples were collected from different locations and were determined in the laboratory by Oedometer test. The results showed that the coefficient of consolidation of soft soil varies from 0.052.10-3 to 3.3.10-3cm2/s, otherwise the compression index changes from 0.156 to 1.703, soil is in a normally consolidated or over the consolidated state. These properties also change differently with depth. It also indicated that the compressive index of soft soil has a fine linear relationship with the liquid limit، water content, and void ratio. The coefficient of consolidation of soft soil decreases with the increase of compression pressure. These parameters are basic for calculating the settlement of underground structures in Ho Chi Minh City.

scholarly journals Research on Horizontal Coefficient of Consolidation of Vietnam’s Soft Soil

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Nu Nguyen Thi ◽  
Bui Truong Son ◽  
Do Minh Ngoc
Keyword(s):  
Experimental Study ◽  
Laboratory Tests ◽  
Soft Soil ◽  
Coefficient Of Consolidation ◽  
Prefabricated Vertical Drains ◽  
Vertical Drains ◽  
Constant Rate ◽  
Different Types ◽  
Cell Test ◽  
Dissipation Test

The horizontal coefficient of consolidation is the most important parameter for designing the improvement of soil soft by prefabricated vertical drains (PVDs) combined with surcharge and vacuum preloading. This paper presents the experimental study on the horizontal coefficient of consolidation (ch) of some soft soils distributed in Vietnam. The ch value was determined by the laboratory test and CPTu dissipation test. The laboratory tests included the Rowe consolidation cell test and constant rate of strain consolidation with radial drainage test. Two types of consolidation laboratory tests were performed. The experimental results indicated that the ch value is always larger than the vertical coefficient of consolidation of soil (cv). The ratio of ch/cv depends on the consolidated pressure, type of soil, and the anisotropy of soil. The ratio of ch/cv is different in different types of soft soil in Vietnam. In the normally consolidated state, the ch/cv ratio ranges from 1.35 to 10.59. It was necessary to choose the ch value at the consolidated stress level for calculating the PVD spacing.

scholarly journals Physical and Mechanical Properties of a Bulk Lightweight Concrete with Expanded Polystyrene (EPS) Beads and Soft Marine Clay

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1662 ◽  
Author(s):  
Jianguo Wang ◽  
Bowen Hu ◽  
Jia Hwei Soon
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Cement Content ◽  
Mass Density ◽  
Physical And Mechanical Properties ◽  
Confining Pressure ◽  
Expanded Polystyrene ◽  
Triaxial Tests ◽  
Filling Material ◽  
Confining Pressures

The variation of physical and mechanical properties of the lightweight bulk filling material with cement and expanded polystyrene (EPS) beads contents under different confining pressures is important to construction and geotechnical applications. In this study, a lightweight bulk filling material was firstly fabricated with Singapore marine clay, ordinary Portland cement and EPS. Then, the influences of EPS beads content, cement content, curing time and confining pressure on the mass density, stress–strain behavior and compressive strength of this lightweight bulk filling material were investigated by unconsolidated and undrained (UU) triaxial tests. In these tests, the mass ratios of EPS beads to dry clay (E/S) were 0%, 0.5%, 1%, 2%, and 4% and the mass ratios of cement to dry clay (C/S) were 10% and 15%. Thirdly, a series of UU triaxial tests were performed at a confining pressure of 0 kPa, 50 kPa, 100 kPa, and 150 kPa after three curing days, seven curing days, and 28 curing days. The results show that the mass density of this lightweight bulk filling material was mainly controlled by the E/S ratio. Its mass density decreased by 55.6% for the C/S ratio 10% and 54.9% for the C/S ratio 15% when the E/S ratio increased from 0% to 4% after three curing days. Shear failure more easily occurred in the specimens with higher cement content and lower confining pressure. The relationships between compressive strength and mass density or failure strain could be quantified by the power function. Increasing cement content and reducing EPS beads content will increase mass density and compressive strength of this lightweight bulk filling material. The compressive strength with curing time can be expressed by a logarithmic function with fitting correlation coefficient ranging from 0.83 to 0.97 for five confining pressures. These empirical formulae will be useful for the estimation of physical and mechanical properties of lightweight concretes in engineering application.

scholarly journals Experimental Investigation on Small-Strain Stiffness of Marine Silty Sand

2020 ◽  
Vol 8 (5) ◽  
pp. 360 ◽  
Author(s):  
Qi Wu ◽  
Qingrui Lu ◽  
Qizhou Guo ◽  
Kai Zhao ◽  
Pen Chen ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Void Ratio ◽  
Reduction Rate ◽  
Confining Pressure ◽  
Small Strain ◽  
Silty Sand ◽  
Bender Element ◽  
Small Strain Stiffness ◽  
Alternative State ◽  
State Index

The significance of small-strain stiffness (Gmax) of saturated composite soils are still of great concern in practice, due to the complex influence of fines on soil fabric. This paper presents an experimental investigation conducted through comprehensive bender element tests on Gmax of marine silty sand. Special attention is paid to the influence of initial effective confining pressure ( σ c 0 ′ ), global void ratio (e) and fines content (FC) on Gmax of a marine silty sand. The results indicate that under otherwise similar conditions, Gmax decreases with decreasing e or FC, but decreases with increasing FC. In addition, the reduction rate of Gmax with e increasing is not sensitive to σ c 0 ′ , but obviously sensitive to changes in FC. The equivalent skeleton void ratio (e*) is introduced as an alternative state index for silty sand with various FC, based on the concept of binary packing material. Remarkably, the Hardin model is modified with the new state index e*, allowing unified characterization of Gmax values for silty sand with various FC, e, and σ c 0 ′ . Independent test data for different silty sand published in the literature calibrate the applicability of this proposed model.

Study on the Compressibility of the Silt in Hangzhou, China

2013 ◽  
Vol 419 ◽  
pp. 853-857
Author(s):  
Zhen Ying Zhang ◽  
Da Zhi Wu ◽  
Cha Wang
Keyword(s):  
Laboratory Tests ◽  
Void Ratio ◽  
Soil Mechanics ◽  
Soil Samples ◽  
Compression Index ◽  
Uniformity Coefficient ◽  
Initial Void Ratio ◽  
Natural Density ◽  
Engineering Parameters ◽  
The Relationship

To investigate the compressibility of the silt, three soil samples are collected from Xiasha zone, Hangzhou, Zhejiang Province, China. The geotechnical engineering parameters of the silt soil are measured in the soil mechanics laboratory. Tests results show that the uniformity coefficient of the silt is 13.6, the natural density is 1.96t/m3, the moisture content is 17.0%, the plasticity index is 9.4, the compression coefficient varies from 0.06 to 0.40MPa-1, and the compression index varies from 0.015 to 0.108. Finally, the properties of the compression are studied, and find that the compressibility of the silt soil is very large, and the relationship between the initial void ratio and the logarithm pressure is linear.

Prediction of the Preconsolidation Pressure and Recompression Index of Soils

1985 ◽  
Vol 8 (4) ◽  
pp. 199 ◽  
Author(s):  
VP Drnevich ◽  
TS Nagaraj ◽  
BR Srinivasa Murthy
Keyword(s):  
Preconsolidation Pressure ◽  
Recompression Index

Experimental Study on Shear Strength Considering Initial Void Ratio and Plasticity Index

2013 ◽  
Vol 405-408 ◽  
pp. 63-67
Author(s):  
Xing Chen Wang ◽  
Ri Qing Xu ◽  
Jian Feng Zhu
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Deviatoric Stress ◽  
Plasticity Index ◽  
Test Results ◽  
Compression Tests ◽  
Functional Relationships ◽  
Initial Void Ratio

A series of drained triaxial compression tests under different conditions were performed to quantitatively study the influence of the initial void ratio and plasticity index on the shear strength of remolded saturated clays. The test results show that both the peak stress friction angle and peak deviatoric stress decrease with increasing initial void ratio and plasticity index of the soil under the same confining pressure; whereas, they increase with increasing confining pressure of the soil under the same initial void ratio and plasticity index. A new synthesized physical parameter λ, which simultaneously represent both the type and the condition of remolded saturated clays, is defined based on the test results in this work. The functional relationships among the parameters φd and peak deviatoric stress in Mohr-Coulomb equation and the parameter λ are established to develop a modified Mohr-Coulomb equation by considering physical properties of soil. In this equation, only two input parameters, i.e., λ and the confine pressure, are needed to predict the shear strength of the soil. In order to check the accuracy of the proposed equation, laboratory tests were conducted to evaluate against the predicted results. The results show that the peak shear strength of remolded saturated clays can be well described by the proposed equation. Key words: shear strength; Mohr-Coulomb equation; remolded saturated clays; initial void ratio; plasticity index.

Characterization of a cemented sand with the pulse-velocity method

2006 ◽  
Vol 43 (3) ◽  
pp. 294-309 ◽  
Author(s):  
Zahid Khan ◽  
Anwar Majid ◽  
Giovanni Cascante ◽  
D Jean Hutchinson ◽  
Parsa Pezeshkpour
Keyword(s):  
Compressive Strength ◽  
Water Content ◽  
Wave Velocity ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Cement Content ◽  
Pulse Velocity ◽  
Initial Water Content ◽  
Strain Property ◽  
Cemented Sand

The effect of variation in cement content, initial water content, void ratio, and curing time on wave velocity (low-strain property) and unconfined compressive strength (large-strain property) of a cemented sand is examined in this paper. The measured pulse velocity is compared with predictions made using empirical and analytical models, which are mostly based on the published results of resonant column tests. All specimens are made by mixing silica sand and gypsum cement (2.5–20% by weight) and tested under atmospheric pressure. The wave velocity reaches a maximum at optimum water content, and it is mostly affected by the number of cemented contacts; whereas compressive strength is governed not only by the number of contacts but also by the strength of contacts. Experimental relationships are developed for wave velocity and unconfined compressive strength as functions of cement content and void ratio. Available empirical models underpredict the wave velocity (60% on average), likely because of the effect of microfractures induced by confinement during the testing. Wave velocity is found to be a good indicator of cement content and unconfined compressive strength for the conditions of this study.Key words: wave velocity, low-strain stiffness, cemented sands, elastic moduli, unconfined compressive strength.

Sign in / Sign up

Export Citation Format

Share Document